-
Makita 9040L - page 1
A A AA Overall length No load speed (RPMl B Net weight Spindle thread MODEL 9040L INSTRUCTION MANUAL DOUBLE INSULATION 6,000 I 470 mm (18-1/2") I 4.8 kg (10.6 Ibsl I 5/8"-11 UNC * Manufacturer reserves the right to change specifications without notice. * Note: Specifications may differ from country to country. WARNING: For your personal s ...
-
Makita 9040L - page 2
GENERAL SAFETY RULES (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not ...
-
Makita 9040L - page 3
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. ...
-
Makita 9040L - page 4
Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rated for at last the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3. Hold tool by insulated gripping surfaces when ...
-
Makita 9040L - page 5
SYMBOLS The followings show the symbols used for tool. ................................. volts ................................. herts ............................ ................ ......... kilograms ............................. ............................. ..................... seconds ................................. alternating current ... . ...
-
Makita 9040L - page 6
Installing side grip (auxiliary handle) Always install the side grip on the tool securely before operation. The side grip can be installed in any of three positions on the sides of the tool, whichever is convenient and keeps the guard properly positioned. Always hold the tool’s switch handle and the side grip firmly with both hands during operati ...
-
Makita 9040L - page 7
To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. 1 r Lock nut wrench Shaft lock 3- I To remove the disc, follow the installation procedure in reverse. IF USED AS A GRINDER NOTE: Use grinder accessories specified in this manual. These must be purchas ...
-
Makita 9040L - page 8
Installing or removing depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the spindle. To tighten the lock nut, press the shaft lock firmly so that the spindle c ...
-
Makita 9040L - page 9
Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15O to the workpiece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel ha ...
-
Makita 9040L - page 10
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should be replace ...
-
Makita 9040L - page 11
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. @Wheel guard @Depressed center wheel (1 Per pk ...
-
Makita 9040L - page 12
@Rubber pad Part No. 743012 Part No. 742067-A-5 742069-A-5 7 Grit Diameter Imm) 16 24 @Abrasive disc (5 per pkg) 741415-A @Sanding lock nut 48 (For abrasive disc) Part No. 224517-1 A24R 9" x 114" x 518" @Wire cup brush Part No. I Diameter (mm) .-I 743206-A 150 16") 743206-8 @Urethane washer 14 Part No. 261039-0 When using wire b ...
-
Makita 9040L - page 13
May-13--'98 EN ANGLE SANDER Model 9040L Note: The switch, noise suppressor and other part configurations may differ from country to country. 13 ...
-
Makita 9040L - page 14
MODEL 9040L %M AtD DESCRIPTION 0ct.-08-'96 US 'LtM GFD DESCRIPTION MACHINE ~ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 - 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 - FIELD ASSEMBLY Baffle Plate Ball Bearing 6200DDW lnsdation Washer ARMATURE ASSEMBLY (With item 3. 4 & 61 Fan 80 Bearing Retainer 60 Ball Bearing 630 ...
-
Makita 9040L - page 15
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh ...
¿Tienes una pregunta acerca de Makita 9040L?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 9040L, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 9040L probablemente compartirá una forma de solucionarlo.