Makita 9040Lの取扱説明書

15ページ 0.7 mb
ダウンロード

ページに移動 of 15

Summary
  • Makita 9040L - page 1

    A A AA Overall length No load speed (RPMl B Net weight Spindle thread MODEL 9040L INSTRUCTION MANUAL DOUBLE INSULATION 6,000 I 470 mm (18-1/2") I 4.8 kg (10.6 Ibsl I 5/8"-11 UNC * Manufacturer reserves the right to change specifications without notice. * Note: Specifications may differ from country to country. WARNING: For your personal s ...

  • Makita 9040L - page 2

    GENERAL SAFETY RULES (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not ...

  • Makita 9040L - page 3

    11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. ...

  • Makita 9040L - page 4

    Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rated for at last the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3. Hold tool by insulated gripping surfaces when ...

  • Makita 9040L - page 5

    SYMBOLS The followings show the symbols used for tool. ................................. volts ................................. herts ............................ ................ ......... kilograms ............................. ............................. ..................... seconds ................................. alternating current ... . ...

  • Makita 9040L - page 6

    Installing side grip (auxiliary handle) Always install the side grip on the tool securely before operation. The side grip can be installed in any of three positions on the sides of the tool, whichever is convenient and keeps the guard properly positioned. Always hold the tool’s switch handle and the side grip firmly with both hands during operati ...

  • Makita 9040L - page 7

    To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. 1 r Lock nut wrench Shaft lock 3- I To remove the disc, follow the installation procedure in reverse. IF USED AS A GRINDER NOTE: Use grinder accessories specified in this manual. These must be purchas ...

  • Makita 9040L - page 8

    Installing or removing depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the spindle. To tighten the lock nut, press the shaft lock firmly so that the spindle c ...

  • Makita 9040L - page 9

    Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15O to the workpiece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel ha ...

  • Makita 9040L - page 10

    MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should be replace ...

  • Makita 9040L - page 11

    ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. @Wheel guard @Depressed center wheel (1 Per pk ...

  • Makita 9040L - page 12

    @Rubber pad Part No. 743012 Part No. 742067-A-5 742069-A-5 7 Grit Diameter Imm) 16 24 @Abrasive disc (5 per pkg) 741415-A @Sanding lock nut 48 (For abrasive disc) Part No. 224517-1 A24R 9" x 114" x 518" @Wire cup brush Part No. I Diameter (mm) .-I 743206-A 150 16") 743206-8 @Urethane washer 14 Part No. 261039-0 When using wire b ...

  • Makita 9040L - page 13

    May-13--'98 EN ANGLE SANDER Model 9040L Note: The switch, noise suppressor and other part configurations may differ from country to country. 13 ...

  • Makita 9040L - page 14

    MODEL 9040L %M AtD DESCRIPTION 0ct.-08-'96 US 'LtM GFD DESCRIPTION MACHINE ~ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 - 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 - FIELD ASSEMBLY Baffle Plate Ball Bearing 6200DDW lnsdation Washer ARMATURE ASSEMBLY (With item 3. 4 & 61 Fan 80 Bearing Retainer 60 Ball Bearing 630 ...

  • Makita 9040L - page 15

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh ...

メーカー Makita カテゴリー Sander

Makita 9040Lのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 9040Lの取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita 9040Lの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita 9040Lの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita 9040Lの取り付け説明書、サービスマニュアル、簡易説明書、またはMakita 9040Lのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita 9040Lの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita 9040Lデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita 9040Lを使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita 9040Lユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita 9040Lの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita 9040Lの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita 9040Lに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita 9040Lデバイスの基本機能を使うにあたってのヒント。 Makita 9040Lのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita 9040Lに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita 9040Lのメーカー/サービスへの連絡先に関する情報。

Makita 9040Lについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita 9040Lの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita 9040Lで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)