-
IDEAL INDUSTRIES 61-320 - page 1
IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-320 MODEL: 61-322 MODEL: 61-324 The Service Information provid es the following in formation: • Precautions and safety information • Specificatio ns • Performance test procedure • Calibration and cali bration adjustm ent procedure • Basic maintenance (cleaning, replacing the battery and fu ...
-
IDEAL INDUSTRIES 61-320 - page 2
TABLE OF CONTENTS Page # Introduction 1 Precautions an d Safety Inf ormation 1 Symbols 1 Safety 2 Specifications 3 General Specification 3 Voltage Specifications 4 Current Specifications 5 Resistance, Diode, Continuity Specifications 5 Capacitance , Frequency S pecifications 6 Physical and environm ent characteristics 7 Certification and compliance ...
-
IDEAL INDUSTRIES 61-320 - page 3
Page 1 Introduction Warning To avoid shoc k or injury , do not per form the verification tests or cal ibration pr ocedures described in this manual unless you are qualified to do so. The information provided in th is document is for the use of qualified personnel only. Caution The 61-320, 61-322, and 61-3 24 contain part s that can be damaged by st ...
-
IDEAL INDUSTRIES 61-320 - page 4
Page 2 SAFETY Review the fol lowing safety preca utions to avoid inj ury and pre vent dam age to this product or any product s connected to it. To avoid potential h azards, use the product only as specified. CAUTION. These statements iden tify conditions or practices that could result in d amage to the e quipm ent or other pr operty. WARNING. These ...
-
IDEAL INDUSTRIES 61-320 - page 5
Page 3 SPECIFICATIONS All specificatio ns are warrante d unless n oted typi cal and appl y to the 61-32 0, 61-322 an d 61-324. Stated accuracies are at 23 ºC ± 5 ºC at less than 80% relative humidity and without the ba ttery indicator di splayed. General specifications Characteristic s Description Display c ount 6,000 Numeric updat e rate 1.5 ti ...
-
IDEAL INDUSTRIES 61-320 - page 6
Page 4 Measurement Characteristics Accuracy is ± (% reading + number of digits) at 23 ° C ± 5 ° C , less than 80% R.H. DC Volts Range Resolution Accuracy Over voltage protection 600.0m V 100µV 6.000V 1mV 60.00V 10mV 600.0V 100mV 1000V 1V ±(0.5% + 2dgt) 1000V rms AC Volts Range Resolution Accuracy Over voltage protection 600.0m V 100µV Unspec ...
-
IDEAL INDUSTRIES 61-320 - page 7
Page 5 DC Current Range Resolution Accuracy Over voltage protection 600.0µA 1m V 6000µA 1mV 60.00m A 10mV 600.0m A 100mV ±(1.0%+2 dgt ) 600V rms1A (600) Fast blow fuse AC Current Range Resolution Accuracy Over voltage protection 600.0µA 1m V 6000µA 1mV 60.00m A 10mV 600.0m A 100mV ±(1.5%+2 dgt ) 50Hz ~ 50 0Hz * 600V rms 1A (600) Fa st blow fu ...
-
IDEAL INDUSTRIES 61-320 - page 8
Page 6 Frequency Range Sensitivity Accuracy Overload protection 6000Hz 60.00KHz 600.0KHz 100mV rm s * 6.000MHz 25 0mV rms 60.00MHz 1V rms Frequency : 0.01%±1di git 600V rms * Less t han 20Hz, the sensitivity is 1.5V rms. Capacitance Range Accura cy Overload protection 6.000nF 60.00nF 600.0nF 6.000µF 60.00µF 600.0µF 6.000m F * ±(1.9% + 8 dgt) 6 ...
-
IDEAL INDUSTRIES 61-320 - page 9
Page 7 Physical and E nvironmental C haracteristi cs Characteristic s Description Dime nsions (H x W x D) 158mm x 76m m x 38mm 164mm x 82mm x 44mm (with holst er) Weight (with battery) 0.3Kg With holster 0.5Kg Environmental Characteristics Descripti on Temperature operating 0 to + 5 0ºC Non-Operating -20 to + 60 º C Humidity (operating) < 80% ...
-
IDEAL INDUSTRIES 61-320 - page 10
Page 8 Required Equipment Required equipment is listed in Table B. I f the recom mended m odels are not avail able, equi pment wi th equivale nt specifications may be used. Repai rs or ser vicing sh ould be performed o nly by q ualified per sonnel. Table B. Required Equipment Equipment Required Characteristics Recommended Model Calibrator AC Voltag ...
-
IDEAL INDUSTRIES 61-320 - page 11
Page 9 Basic Maintenance Warning To avoid shoc k, rem ove the test leads and an y input signals before opening the case or re placing the battery or fuses. Opening the Meter Case Caution To avoid unintentional short circ uit, always place the uncovered m eter assembly on a protective surface . When the case of the m eter is open, circuit connection ...
-
IDEAL INDUSTRIES 61-320 - page 12
Page 10 Testing Fuses To test the internal fuses of the meter: 1. Turn the rotary selector switch to the Ω positio n. 2. To test FS1, plug a test lead into V Ω Hz input terminal and touch the probe to th e mA input terminal. The display sh ould indicate bet ween 0.0 to 0.2 Ω . FS1 (1 A 600V - Bussmann BBS-1 recomm ended). If display reads hig ...
-
IDEAL INDUSTRIES 61-320 - page 13
Page 11 Performance Tests The following performance tests ve rify the complete ope ra bility of the meter and c heck the accuracy of each meter function against the meter’s specifications. Accuracy specifications are valid for a period of one y ear after calibration, when measured at an operating temp er atu r e of 1 8ºC to 28ºC and at a maximu ...
-
IDEAL INDUSTRIES 61-320 - page 14
Page 12 Table 1 AC Voltage Test: Step Input Frequency Reading 1 5.800V 50Hz 5.743 to 5.857 2 5.800V 500Hz 5.743 to 5.857 3 58.00V 50Hz 57.43 to 58.57 4 58.00V 500Hz 57.43 to 58.57 5 580.0V 50Hz 574.3 to 585.7 6 580.0V 500Hz 574.3 to 585.7 7 750V 50Hz 738 to 762 8 750V 500Hz 738 to 762 6. Turn the rotary switch to “V ” position. 7. Set the calib ...
-
IDEAL INDUSTRIES 61-320 - page 15
Page 13 Testing the Capacitance Function The meter measures capacitance by c h arging the capac itor with a known direct current, measuring the resultant voltage, and calcu lating the capacitance. If the same capacitan ce is m easured on an impedance bridge, a different rea ding may result. This variance is likely to be greater at higher frequencie ...
-
IDEAL INDUSTRIES 61-320 - page 16
Page 14 Table 5 AC mA Test: Step Source Frequency Reading 1 58.00mA 50Hz 56.93 to 59.07 2 58.00mA 500Hz 56.93 to 59.07 3 580.0m A 50Hz 569.3 to 590.7 4 580.0m A 500Hz 569.3 to 590. 7 6. Turn the rotary switch to mA . 7. Apply the inputs for steps 1-2 in Table 6. 8. For each input, compare the reading on the meter display to the read ing in Table 6. ...
-
IDEAL INDUSTRIES 61-320 - page 17
Page 15 Table 8 Frequency Test: Step Source Level Reading 1 5.600KHz 100m V rms 5.598 to 5.602 2 56.00KHz 100m V rms 55.98 to 56 .02 3 560.0KHz 100m V rms 559.8 to 56.02 4 5.600M Hz 250mV rm s 5.598 to 5.602 5 56.00M Hz 1V rms 55.98 to 56.02 Calibration Calibrate the meter once a year to ensure that it performs according to specifications. Per for ...
-
IDEAL INDUSTRIES 61-320 - page 18
Page 16 Figure 3 - Calibrati on Adjustment Point s Form number TM61320-2-4 Rev 2 September 2002 ...
-
IDEAL INDUSTRIES 61-320 - page 19
Form number TM61320-2-4 Rev 2 September 2002 Page 17 ...
¿Tienes una pregunta acerca de IDEAL INDUSTRIES 61-320?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con IDEAL INDUSTRIES 61-320, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con IDEAL INDUSTRIES 61-320 probablemente compartirá una forma de solucionarlo.