-
Elinchrom BX100 - page 1
English Multivoltage 90/260V elinca sa switzerland www .elinchr om.com Operating Manual Elinca S.A Style BX 01.09.2008 ENG (73286) Printed in S wi tzerland Style BX 100/400 ...
-
Elinchrom BX100 - page 2
1 P .S: T echnical data subject to change. The listed values ar e guide values which may vary due to tolerances in components used. Introduction 2 Declaration of conformit y , disposal and recycling, CE marking 3 Safety notice and precaution 4 Operating instructions 5 Control P anel 6 Switch and Fuse 7 Modelling Light 8 Digital power display , Phot ...
-
Elinchrom BX100 - page 3
2 The quality of light and ex ceptional performance is the result of long research, application of demanding principles, the long experience of ELINCHROM in lighting products for the studio and the utilization of the latest technology in this area. T otally integrated to the r ange of the ELINCHROM ashes, the Style 100BX - 400BX units maintain t ...
-
Elinchrom BX100 - page 4
3 CE marking The shipped version of this device complies with the requirements of ECC dir ectives 89/336/ECC «Electromagnetic compatibility» and 73/23/ECC «Low voltage dir ective». Notational Conventions The meaning of the symbols and fonts used in this manual are as f ollows: Pa y particular attention to text marked with this symbol. F ailure ...
-
Elinchrom BX100 - page 5
4 • T ransport the ash unit with care and only in its original packaging or another corresponding packaging t to protect it against knocks and jolts. • T ransport only in complete discharged conditions. W ait a minimum 30 minutes after removing from mains supply befor e packaging and transportation. • Never drop the ash unit (danger ...
-
Elinchrom BX100 - page 6
5 3 1 6 11 12 The units Style BX (Multivoltage) are adapted f or operation on 90 - 260V/50 - 60Hz. Before connecting for the rst time, check to mak e sure that your Modelling lamp coincides with the voltage line. They must always be connected to an earthed ( gr ounded) mains supply . All Style BX units have a ba yonet mount and locking ring re? ...
-
Elinchrom BX100 - page 7
6 Overview of controls 1. Mains inlet socket 2. Mains fuse (slow blow) 3. Mains light up on/off switch 4. Modelling fuse (f ast blow) 5. Open-ash 6. Synchro-sock ets + jack 3.5 mm 7 . Digital power display and char ge/discharge indicator 8. Acoustic recharging signal (Beep) 9. Slave cell switch on/off 10. Photocell receptor 11. Power adjustment ...
-
Elinchrom BX100 - page 8
7 2 3 1 Mains fuse Modelling fuse Mains switch (Only tempered) Mains socket 4 Mains Supply With the MAINS SWITCH (3) switched off ("O" position), rmly push in the plug of the original ELINCHROM mains cord into the mains socket (1). Mains Switch The switch should light up when the compact is switched on ("I" position). (Switch ...
-
Elinchrom BX100 - page 9
8 Modelling lamps and fuse for 90/140V Unit Modelling lamp Code Socket Fuse Code Style 100BX 150W Halostar 23019 E27 4AF 19035 Style 400BX 150W Halostar 23019 E27 4AF 19035 Option: 150W Halogen 23031 GX 6,35 4AF 19035 Option: 200W Halogen 23033 GX 6,35 4AF 19035 The touch pad (14) controls the modelling lamp on/off and the proportional light. Selec ...
-
Elinchrom BX100 - page 10
9 10 Photocell receptor 5 T est and ready 9 Cell Modellling light controls Power displa y The actual ash power is displayed in a f -stop compatible format. The power range is 5 f -stops. The digital display , provides continuous power indication of the ash and modelling lamp. The controls cov er a continuous output range from full power 1/1 t ...
-
Elinchrom BX100 - page 11
10 EL -Skyport triggers ashes without sync cords over a distance of approximately 100 m. Further detailed information please nd under : www .elinchrom.com / Products / RX Multi Remote Open ash "test" Having pressed the touch pad to release a ash, the green «READ Y» light will appear again once the unit is recharged. If the g ...
-
Elinchrom BX100 - page 12
11 If the unit does not ash but the ON/OFF switch indicates that there is power , it could be that the ash tube needs replacing. Note:Flash tubes (Swiss quality) have a long life with average use, but multiashing in long sequences can cause overheating of the electrodes leading to pr ematur e ageing, or perhaps the astube is br oken or ...
-
Elinchrom BX100 - page 13
12 Flash power J(Ws) 100 400 Power supply V 90/260 90/260 F-stop, 1m, 100 ISO , with reector 48° 32,5 64,5 Control range J(Ws) 5-100 25-400 Recycling time (230 V) s 0,2-0,5 0,3-1,1 Flash duration (t 0,5) 1/1 s 1/1700 1/850 (t 0,5) 1/16 s 1/1150 1/450 Modelling output W 150 150 V oltage across sync cable V 5 5 Connected load A/V A (W) 8/2080 8/2 ...
-
Elinchrom BX100 - page 14
13 Single units do not include Reflectors - Product range and specifications subject to change. No guarantee for misprints. EL-Skyport RX Trigger Set 19362 Digital RX 2400 230V: 10258 110V: 10257 Digital RX 1200 230 V: 10256 110 V: 10255 EL-Skyport RX Trigger Set 19362 Digital 1500 AS 230 V 10248 110 V 10247 Digital 3000 AS 230 V 10254 110 V 10253 ...
-
Elinchrom BX100 - page 15
14 This ELINCHROM product will be repaired free of char ge by the vending agent if during a period of 24 months from date of purchase its working order is impaired thr ough a manufacturing or material defect. The fault y product should be immediately sent to the authorized dealer or ELINCA agent. This guarantee is not v alid for equipment which has ...
-
Elinchrom BX100 - page 16
www.elinchrom.com ...
¿Tienes una pregunta acerca de Elinchrom BX100?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Elinchrom BX100, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Elinchrom BX100 probablemente compartirá una forma de solucionarlo.