-
Husqvarna DM 340 - page 1
G G G G B B B B E E E E S S S S P P P P T T T T G G G G R R R R DM 340 GB ES PT GR Oper ator’ s manual Please read the operator’ s manual car efully and make sure y ou understand the instructions before using the machine. Manual de instrucciones Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar ...
-
Husqvarna DM 340 - page 2
2 – English KEY T O SYMBOLS Symbols on the machine: W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or fatal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Approv ...
-
Husqvarna DM 340 - page 3
English – 3 CONTENTS Contents KEY T O SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’ s manual: ............................... 2 CONTENTS Contents ...................................................................... 3 PRESENT A TION DM 340 .............................................. ...
-
Husqvarna DM 340 - page 4
4 – English PRESENT A TION DM 340 It is our wish that you will be satisfied with y our product and that it will be your companion f or a long time. Think of this operator ′ s manual as a v aluable document. By follo wing its ′ content (using, ser vice, maintenance etc) the lif e span and the second-hand value of the machine can be e xtended. ...
-
Husqvarna DM 340 - page 5
English – 5 WHA T IS WHA T? What is what on the drilling machine? 1 Drill spindle 2 Gearbo x and motor module 3 Carr ying handle 4 Gear knob 5 Quick mount, f or Husqvarna stand 6 W ater connector 7 LEDs f or indicating power output 8 Switch 9 Smar tstar t TM 10 Inspection cov er 11 Leakage hole 12 Inspection hatch 13 Junction coupling (accessory) ...
-
Husqvarna DM 340 - page 6
6 – English SAFETY INSTR UCTIONS Steps before using a ne w drilling machine • Do not use the drilling machine without first reading and understanding the contents of this Operator’ s Manual. • DM 340 is an electric stand dr ill, intended f or drilling holes in concrete, bricks and v ar ious stone materials. • The machine is intended f or ...
-
Husqvarna DM 340 - page 7
English – 7 SAFETY INSTR UCTIONS General safety precautions W ork area safety • K eep wor k area clean and well lit. Cluttered or dark areas invite accidents . • Do not operate pow er tools in explosiv e atmospheres, such as in the presence of flammable liquids , gases or dust. P ower tools create sparks which may ignite the dust or fumes. ? ...
-
Husqvarna DM 340 - page 8
8 – English SAFETY INSTR UCTIONS Use and care • Ne ver use a machine that is f aulty . Carr y out the checks, maintenance and ser vice instructions descr ibed in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists . See instructions under the heading Maintenance. • Inspection and/or mai ...
-
Husqvarna DM 340 - page 9
English – 9 SAFETY INSTR UCTIONS Machine ′′ ′ ′ s saf ety equipment This section describes the machine ′ s safety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine . Switch ...
-
Husqvarna DM 340 - page 10
10 – English ST ARTING AND ST OPPING Bef ore star ting Make sure that: • P ower s witch, cord and electrical outlet are intact. If not, they m ust be replaced by an authorised repair man. • Cooling air vents are not b locked. • The machine and its equipment are correctly installed. • The stand is properly fixed and that the drill is prop ...
-
Husqvarna DM 340 - page 11
English – 11 MAINTENANCE General The lif etime of your machine can be e xtended considerably if it is used, cared f or and maintained in the proper manner . Changing the drill bit 1 Pull out the plug. 2 Get: - The new drill bit. - Open-ended spanners, siz e 24 mm and 32 mm. - Water-resistant grease . 3 Remov e the old dr ill bit using the open-en ...
-
Husqvarna DM 340 - page 12
12 – English MAINTENANCE 6 If necessar y contact your dealer to clean the gearbo x. 7 P our the new oil into the gearbo x, about 0.5 litres. 8 Check that the sealing lip on the r adial seal is intact. 9 Reassemble the machine and scre w in the four screws . Be careful when assembling so as not to damage the radial seal. Replacing the carbon brush ...
-
Husqvarna DM 340 - page 13
English – 13 TECHNICAL D A T A DM 340 Electric motor Single-phase Rated voltage , V 230 Rated output, W 3600 Rated current, A 16 W eight, kg 14 Max. diameter drill bit, mm/inch 400/16 W ater cooling Spindle thread G 1 1/4” W ater connector G 1/4” W ater pressure - max, bar 8 Noise emissions Sound power le vel, measured, EN 12348:2000, dB(A) 9 ...
-
Husqvarna DM 340 - page 14
14 – English TECHNICAL D A T A EC-declaration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna DM 340 , from 2009´s serial numbers and onwards (the y ear is clearly stated in plain text on the rating plate with subsequent serial number), ...
-
Husqvarna DM 340 - page 15
English – 15 WIRING DIA GRAM ...
-
Husqvarna DM 340 - page 16
´®z+TIi¶0G¨ 2009-04-15 ´®z+TIi¶0G¨ 1152417-30 ...
¿Tienes una pregunta acerca de Husqvarna DM 340?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Husqvarna DM 340, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Husqvarna DM 340 probablemente compartirá una forma de solucionarlo.