-
Husqvarna 1152417-30 - page 1
G G G G B B B B E E E E S S S S P P P P T T T T G G G G R R R R DM 340 GB ES PT GR Oper ator’ s manual Please read the operator’ s manual car efully and make sure y ou understand the instructions before using the machine. Manual de instrucciones Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar ...
-
Husqvarna 1152417-30 - page 2
2 – English KEY T O SYMBOLS Symbols on the machine: W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or fatal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Approv ...
-
Husqvarna 1152417-30 - page 3
English – 3 CONTENTS Contents KEY T O SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’ s manual: ............................... 2 CONTENTS Contents ...................................................................... 3 PRESENT A TION DM 340 .............................................. ...
-
Husqvarna 1152417-30 - page 4
4 – English PRESENT A TION DM 340 It is our wish that you will be satisfied with y our product and that it will be your companion f or a long time. Think of this operator ′ s manual as a v aluable document. By follo wing its ′ content (using, ser vice, maintenance etc) the lif e span and the second-hand value of the machine can be e xtended. ...
-
Husqvarna 1152417-30 - page 5
English – 5 WHA T IS WHA T? What is what on the drilling machine? 1 Drill spindle 2 Gearbo x and motor module 3 Carr ying handle 4 Gear knob 5 Quick mount, f or Husqvarna stand 6 W ater connector 7 LEDs f or indicating power output 8 Switch 9 Smar tstar t TM 10 Inspection cov er 11 Leakage hole 12 Inspection hatch 13 Junction coupling (accessory) ...
-
Husqvarna 1152417-30 - page 6
6 – English SAFETY INSTR UCTIONS Steps before using a ne w drilling machine • Do not use the drilling machine without first reading and understanding the contents of this Operator’ s Manual. • DM 340 is an electric stand dr ill, intended f or drilling holes in concrete, bricks and v ar ious stone materials. • The machine is intended f or ...
-
Husqvarna 1152417-30 - page 7
English – 7 SAFETY INSTR UCTIONS General safety precautions W ork area safety • K eep wor k area clean and well lit. Cluttered or dark areas invite accidents . • Do not operate pow er tools in explosiv e atmospheres, such as in the presence of flammable liquids , gases or dust. P ower tools create sparks which may ignite the dust or fumes. ? ...
-
Husqvarna 1152417-30 - page 8
8 – English SAFETY INSTR UCTIONS Use and care • Ne ver use a machine that is f aulty . Carr y out the checks, maintenance and ser vice instructions descr ibed in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists . See instructions under the heading Maintenance. • Inspection and/or mai ...
-
Husqvarna 1152417-30 - page 9
English – 9 SAFETY INSTR UCTIONS Machine ′′ ′ ′ s saf ety equipment This section describes the machine ′ s safety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine . Switch ...
-
Husqvarna 1152417-30 - page 10
10 – English ST ARTING AND ST OPPING Bef ore star ting Make sure that: • P ower s witch, cord and electrical outlet are intact. If not, they m ust be replaced by an authorised repair man. • Cooling air vents are not b locked. • The machine and its equipment are correctly installed. • The stand is properly fixed and that the drill is prop ...
-
Husqvarna 1152417-30 - page 11
English – 11 MAINTENANCE General The lif etime of your machine can be e xtended considerably if it is used, cared f or and maintained in the proper manner . Changing the drill bit 1 Pull out the plug. 2 Get: - The new drill bit. - Open-ended spanners, siz e 24 mm and 32 mm. - Water-resistant grease . 3 Remov e the old dr ill bit using the open-en ...
-
Husqvarna 1152417-30 - page 12
12 – English MAINTENANCE 6 If necessar y contact your dealer to clean the gearbo x. 7 P our the new oil into the gearbo x, about 0.5 litres. 8 Check that the sealing lip on the r adial seal is intact. 9 Reassemble the machine and scre w in the four screws . Be careful when assembling so as not to damage the radial seal. Replacing the carbon brush ...
-
Husqvarna 1152417-30 - page 13
English – 13 TECHNICAL D A T A DM 340 Electric motor Single-phase Rated voltage , V 230 Rated output, W 3600 Rated current, A 16 W eight, kg 14 Max. diameter drill bit, mm/inch 400/16 W ater cooling Spindle thread G 1 1/4” W ater connector G 1/4” W ater pressure - max, bar 8 Noise emissions Sound power le vel, measured, EN 12348:2000, dB(A) 9 ...
-
Husqvarna 1152417-30 - page 14
14 – English TECHNICAL D A T A EC-declaration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna DM 340 , from 2009´s serial numbers and onwards (the y ear is clearly stated in plain text on the rating plate with subsequent serial number), ...
-
Husqvarna 1152417-30 - page 15
English – 15 WIRING DIA GRAM ...
-
Husqvarna 1152417-30 - page 16
´®z+TIi¶0G¨ 2009-04-15 ´®z+TIi¶0G¨ 1152417-30 ...
¿Tienes una pregunta acerca de Husqvarna 1152417-30?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Husqvarna 1152417-30, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Husqvarna 1152417-30 probablemente compartirá una forma de solucionarlo.