-
IDEAL INDUSTRIES Digital Multimeter - page 1
IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-310 This Service Manual provides the following information: ● Precautions and safety information ● Specifications ● Basic maintenance (cleaning, replacing the battery and fuses) ● Performance test procedures ● Calibration and calibration adjustment procedures Form Number: TM61310 Revision: ...
-
IDEAL INDUSTRIES Digital Multimeter - page 2
Form Number TM61310 Rev 2 Aug 2007 T ABLE OF CONTENTS Page Introduction 1 Precautions and Safety Information 1 Symbols 1 Safety 2 S pecifications 3 General S pecifications 3 Measurement Characteristics 4 V olt age S pecifications 4 Current S pecifications 4 Resistance S pecifications 5 Diode Check, Continuity , T emperature S pecifications 5 Auto P ...
-
IDEAL INDUSTRIES Digital Multimeter - page 3
Form Number TM61310 Rev 2 Aug 2007 Page 1 Introduction W arning T o av ures Th y . oid shock or injury , do not perform the verification test s or calibration proced described in the manual unless you are qualified to do so. e information provided in this document is for the use of qualified personnel onl Caution The 61-310 series cont ain part s t ...
-
IDEAL INDUSTRIES Digital Multimeter - page 4
Form Number TM61310 Rev 2 Aug 2007 Page 2 SAFETY Re uct or any For operating instructions, see the 61-310 Di git al Multimeter Instruction Manual. view the following safety precautions to av oid injury and prevent damage to this prod products connected to it. T o avoid potentia l hazards, use the produc t only as specified. CAUTION: These statement ...
-
IDEAL INDUSTRIES Digital Multimeter - page 5
Form Number TM61310 Rev 2 Aug 2007 All S ta ry ind Ge Page 3 SPECIFICA TIONS specifications are warranted unle ss noted typical and apply to the 61-310. ted accuracies are at 23°C±5°C at less than 70% relative humidity and without the batte icator displayed. neral specifications Characteristics Description Display count 3 ½ digit liquid crystal ...
-
IDEAL INDUSTRIES Digital Multimeter - page 6
Form Number TM61310 Rev 2 Aug 2007 Page 4 Me Ac (1) asurement Characteristics curacy is ±(% reading + number of digi ts) at 23°C ± 5°C, less than 80% R.H. DC V olts Range Resolution Accuracy Over v oltage protection 200.0mV 100 μ V 2.000V 1mV 20.00V 10mV 200.0V 100mV 0.5% + 2 600V 1V 0.8% + 2 600V rms Inp (2) ut Impedance: 10M Ω AC V olts Ra ...
-
IDEAL INDUSTRIES Digital Multimeter - page 7
Form Number TM61310 Rev 2 Aug 2007 Page 5 (4) Resist ance Range Resolution Accuracy Over v oltage protection 200.0 Ω * 1 0.1 Ω 0.8% + 4 2.000K Ω 1 Ω 20.00K Ω 10 Ω 200.0K Ω 100 Ω 2.000M Ω 1K Ω 0.8% + 2 20.00M Ω * 2 10K Ω 3.0% + 3 250V rms Op * 1 < (5) en circuit V oltage: -1.5V approx. 5 digit of reading rolling. * 2 ± 2% ...
-
IDEAL INDUSTRIES Digital Multimeter - page 8
Form Number TM61310 Rev 2 Aug 2007 Page 6 Physical and Env ironmental Characteristics Characteristics Description Dimensions (H×W×D) 150mm(H) ×76mm (W) ×38mm(D) (with holster) 5.9” (H) x 3.0”(W) x1.5”(D) Weight (with battery& holster) 0.219Kg (7.1 oz.) Environment al characteristics Description T emperature operating range 0 to +40°C ...
-
IDEAL INDUSTRIES Digital Multimeter - page 9
Form Number TM61310 Rev 2 Aug 2007 Page 7 Re Required equipm le B. If the recommended models are not available, equipment with equivalent specifications may be used. Repa performed only b T able E Characteristics ended Model quired Equipment ent is listed in T ab irs or servicing should be y qualified personnel. B. Required Equipment quipment Requi ...
-
IDEAL INDUSTRIES Digital Multimeter - page 10
Form Number TM61310 Rev 2 Aug 2007 Page 8 Basic Maintenance W arning avoid shock, remove the test leads and any input signals T o before opening the case or rep Op lacing the battery or fuses. ening the Meter Case Caution ircuit, alwa ys place the unco T o avoi onal short c vered met protec . Whe uit connect 1. Disconnect test lead ary switc d remo ...
-
IDEAL INDUSTRIES Digital Multimeter - page 11
Form Number TM61310 Rev 2 Aug 2007 Page 9 Replacing Fuses W arning To avoid electrical shock, remove the test leads and any input signals before replacing battery or fuses. the amage or injury, INSTALL ONLY quick a cting fuses with the following Amp/Volt F-310 Fuse: 250mA 250V FAST BLOW Fu 3. Remove the two screws under the battery cover . case unt ...
-
IDEAL INDUSTRIES Digital Multimeter - page 12
Form Number TM61310 Rev 2 Aug 2007 Page 10 Perf The following performance test acc Acc an operating temperature of 18°C to 28°C and a maximum of 80% relative humidity . T o perform the following tests, it is not necessary to open the case, no adjustments are nec the required connecti ons, apply the designated inputs, determine if the reading on t ...
-
IDEAL INDUSTRIES Digital Multimeter - page 13
Form Number TM61310 Rev 2 Aug 2007 Page 11 e Test: Table 2: AC Voltag Step Range Input Frequency Reading 1 200V 2.0V 60Hz 1.0 to 3.0 2 200V 2.0V 400Hz 1.0 to 3.0 3 200V 190.0V 60Hz 186.7 to 193.3 4 200V 190.0V 400Hz 186.7 to 193.3 5 600V 600V 60Hz 583.0 to 617.0 6 600V 600V 400Hz 583.0 to 617.0 T esting the DC milliamp 1 s 1-3 in T able 3. meter r ...
-
IDEAL INDUSTRIES Digital Multimeter - page 14
Form Number TM61310 Rev 2 Aug 2007 Page 12 T able 4: Resistance T est: Step Range Source Reading 1 *200 OHM 2.0 Ω 1.6 to 2.4 2 *200 OHM 190.0 Ω 188.3 to 191.7 3 2K OHM 1.900K 883 to 1 Ω 1. .917 4 20K OHM 19.00K 18.83 to 19.17 Ω 5 200K OHM 190.0K 188.3 to 191.7 Ω 7 20M OHM 19.00M 18.40 to 19.60 Ω *Lead resistance on the 200 ohm range ...
-
IDEAL INDUSTRIES Digital Multimeter - page 15
Form Number TM61310 Rev 2 Aug 2007 Page 13 Cali T o Recalibrate your meter: It is recommended that the Multimeter be ca ch year . 1. Perform calibration at an a rature of 23°C±2°C a nd a relative humidity of <70% Dis nect the te s and turn th ff. Rem s from the front terminals. 2. Position the meter face down. Remove the battery cover screws ...
¿Tienes una pregunta acerca de IDEAL INDUSTRIES Digital Multimeter?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con IDEAL INDUSTRIES Digital Multimeter, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con IDEAL INDUSTRIES Digital Multimeter probablemente compartirá una forma de solucionarlo.