-
Pelco DX9200HDDI - page 1
DX9200HDDI Series IDE V ideo Storage Unit C637M-B (10/03) ® INST ALLA TION/OPERA TION ...
-
Pelco DX9200HDDI - page 2
CONTENTS Section Page REGULA TOR Y NOTICES ............................................................................................................. ......................................................................................... 3 RADIO AND TELEVISION INTERFERENCE ....................................................................... ...
-
Pelco DX9200HDDI - page 3
C637M-B (10/03) 3 REGULA TORY NOTICES This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE Th ...
-
Pelco DX9200HDDI - page 4
4 C637M-B (10/03) IMPORT ANT SAFEGUARDS AND W ARNINGS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not ins ...
-
Pelco DX9200HDDI - page 5
C637M-B (10/03) 5 DESCRIPTION The DX9200HDDI video storage unit is one of the components of the DX9000 system. The storage unit contains up to 14 IDE hard disk drives for storing video information from the DX9000 recorder . Up to four IDE storage units can be connected to a recorder . The storage unit uses redundant arrays of independent disks (RAI ...
-
Pelco DX9200HDDI - page 6
6 C637M-B (10/03) FRONT VIEW Figure 1 shows the features on the front of the IDE storage unit. Figure 1. Front View 1. Panel: Use the features of this panel to view the configuration of the RAID or to enter the environment menu. Y ou must lower this panel to remove or add hard drives. 2. Hard drive trays: There are 14 hot-swappable hard drive trays ...
-
Pelco DX9200HDDI - page 7
C637M-B (10/03) 7 11. Up arrow/Quit button: Used in conjunction with the Controller and ENC buttons. Press to scroll through the information on the LCD display , to move through each menu, or to go back to the previous menu. 12. Down arrow/Info button: Used in conjunction with the Controller and ENC buttons. Press to scroll through the information ...
-
Pelco DX9200HDDI - page 8
8 C637M-B (10/03) INST ALLA TION Make sure the following parts are supplied with the storage unit. 1V ideo Storage Unit with IDE hard drives 2 Power cords (1 USA standard and 1 European standard) 2 External SCSI cables 2 Active terminators (for connecting to SCSI channels) 2 Brackets 6 Screws, M4 x .250-inch, pan head 4 Adjustable support rails 6 S ...
-
Pelco DX9200HDDI - page 9
C637M-B (10/03) 9 MOUNTING The storage unit can be placed on a flat surface, such as a shelf, or it can be installed in a 19-inch (48.26 cm) wide equipment rack. NOTE: Allow one rack unit (1.75 inches or 4.5 cm) of space above the storage unit for air circulation. To install the storage unit in an equipment rack: 1. Attach the two brackets to each ...
-
Pelco DX9200HDDI - page 10
10 C637M-B (10/03) STORAGE RECORDER A HOST B HOST A CHANNEL A SCSI CABLE STORAGE RECORDER A RECORDER B HOST B HOST A CHANNEL A CHANNEL A SCSI CABLE SCSI CABLE Figure 5. One Storage Unit/Two Recorder Configuration HARDWARE CONNECTIONS There are five hardware configurations. Y ou can connect one storage unit to one recorder , one storage unit to two ...
-
Pelco DX9200HDDI - page 11
C637M-B (10/03) 11 CHANNEL A CHANNEL B STORAGE B STORAGE A RECORDER HOST A HOST A SCSI CABLE SCSI CABLE CONNECTING TWO STORAGE UNITS TO ONE RECORDER 1. Connect a SCSI cable from Host A on Storage A to Channel A on the recorder . 2. Connect a SCSI cable from Host A on Storage B to Channel B on the recorder . 3. Plug the power cords into the units an ...
-
Pelco DX9200HDDI - page 12
12 C637M-B (10/03) Figure 7. Three Storage Unit/One Recorder Configuration CONNECTING THREE STORAGE UNITS TO ONE RECORDER 1. Connect a SCSI cable from Host A on Storage A to Channel A on the recorder . 2. Connect a SCSI cable from Host A on Storage B to Channel B on the recorder . 3. Connect a SCSI cable (DX9200HDDI-LCBL) from the Host A Out port o ...
-
Pelco DX9200HDDI - page 13
C637M-B (10/03) 13 CONNECTING FOUR STORAGE UNITS TO ONE RECORDER 1. Connect a SCSI cable from Host A on Storage A to Channel A on the recorder . 2. Connect a SCSI cable from Host A on Storage B to Channel B on the recorder . 3. Connect a SCSI cable (DX9200HDDI-LCBL) from the Host A Out port on Storage A to the Host A In port on Storage C. 4. Connec ...
-
Pelco DX9200HDDI - page 14
14 C637M-B (10/03) OPERA TION The storage unit has been preconfigured to operate using RAID Level 5 or RAID Level 5+1 technology . Pelco recommends RAID Level 5+1. In Level 5+1, a hot spare drive is included. If a hard drive is removed or fails, the redundant data, on the remaining drives, relocates automatically to the hot spare and begins the rec ...
-
Pelco DX9200HDDI - page 15
C637M-B (10/03) 15 TROUBLESHOOTING What do I do when the voltage warning LED illuminates red and an alarm sounds? This happens when the output DC voltage is under 4.5V or over 5.5V , and under 10.2V or over 13.8V . The ENC global fault LED also illuminates. Press the Exit/Alarm reset button to stop the alarm. A low beep continues to sound. There ma ...
-
Pelco DX9200HDDI - page 16
16 C637M-B (10/03) SERVICE HOW TO REPLACE A F AN The fans are hot-swappable. The spare part number for the fan is DX9200HDDI-F AN. THUMBSCREW HANDLE THUMBSCRE W HANDLE Figure 9. Replacing a Fan Figure 10. Replacing a Power Supply 1. Loosen the thumbscrew . 2. Pull the screw to lift the handle. 3. Pull out the defective fan. 4. Slide the new fan int ...
-
Pelco DX9200HDDI - page 17
C637M-B (10/03) 17 HOW TO CHANGE FROM RAID 5 TO RAID 5+1 To change a RAID 5 configuration to a RAID 5+1 configuration, you must add a hot spar e hard drive. A hot spare hard drive becomes the replacement hard drive when a hard drive fails in the RAID 5+1 configuration. Make sure you have the appropri- ate spare drive from Pelco: DX9000DRV-I120 or D ...
-
Pelco DX9200HDDI - page 18
POWER CONNECTOR 40-PIN ATA CABLE CONNECTOR LEVER RELEASE LEVER ATA CABLE CONNECTOR PORT JUMPER POWER PORT PHILLIPS SCREWS TRAY WITH HARD DRIVE Figure 11. Adding a Hard Drive ...
-
Pelco DX9200HDDI - page 19
W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/ MC3600 Series); two ...
-
Pelco DX9200HDDI - page 20
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada Singapore ® ...
¿Tienes una pregunta acerca de Pelco DX9200HDDI?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pelco DX9200HDDI, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pelco DX9200HDDI probablemente compartirá una forma de solucionarlo.