-
Pelco C2410M-1 - page 1
INST ALLA TION 150 Series Camclosure ® Integrated Camera System C2410M-I (1/06) ...
-
Pelco C2410M-1 - page 2
...
-
Pelco C2410M-1 - page 3
C2410M-I (1/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other ...
-
Pelco C2410M-1 - page 4
4 C2410M-I (1/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC, Class A (black-white, EIA and CC ...
-
Pelco C2410M-1 - page 5
C2410M-I (1/06) 5 Description The 150 Series Camclosure ® integrated camera system is an in-ceiling dome incorporating a camera and lens package into a small, discreet, high-security enclosure designed for areas subject to heavy vandalism. The system is perfect for a variety of indoor and outdoor applications and its versatile design allows for mu ...
-
Pelco C2410M-1 - page 6
6 C2410M-I (1/06) Installation INSTALL BACK BOX MOUNTING DIRECTLY TO A WALL OR CEILING 1. Cut a hole 3.5 inches (9 cm) in diameter in the ceiling or wall using the adapter plate as a template. 2. Connect the video cable. 3. Connect the power wires. • For 12 VDC, connect the 24 V AC/12 VDC (red) and GND (black) wires to input power . The blue wire ...
-
Pelco C2410M-1 - page 7
C2410M-I (1/06) 7 MOUNTING TO CEILING T ILE 1. Remove the ceiling tile. 2. Using the adapter plate as a template, cut a hole 3.5 inches (9 cm) in diameter in the ceiling tile for the back box. Punch four screw holes in the ceiling tile. 3. Attach the back box to the ceiling tile and adapter plate with the four 8-32 x 1.25-inch screws (see diagram). ...
-
Pelco C2410M-1 - page 8
8 C2410M-I (1/06) 3. If the heater is installed, plug the heater connector from the camera into the mating connector inside the base. Plug the video connector from the camera into the mating connector inside the base. T urn on power to the camera and monitor . 4. If you have a varifocal lens, hold the assembly in your hand and point the lens toward ...
-
Pelco C2410M-1 - page 9
C2410M-I (1/06) 9 INSTALL DOME AND T RIM RING Place the trim ring and dome over the back box. If the dome has a liner , position the viewing window over the lens of the camera. Tighten the tamper-resistant screws with the supplied 1/8-inch hollow screwdriver bit. Note that the screws are installed at an angle. Adjustments (Color Camera Only) If you ...
-
Pelco C2410M-1 - page 10
10 C2410M-I (1/06) AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fi xed focal length lens with an auto iris, you can adjust the level setting to increase or decrease brightness. FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS . T o adjust the focus, it may be necessary to remove the heater board in order to loosen the lock ...
-
Pelco C2410M-1 - page 11
C2410M-I (1/06) 11 SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there are no bright spots that darken other picture de ...
-
Pelco C2410M-1 - page 12
12 C2410M-I (1/06) SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. For manually setting and locking the white balance, place a white background in front of camera and turn off switch 1. For gamma correction, switch to accurately reproduce scene b ...
-
Pelco C2410M-1 - page 13
C2410M-I (1/06) 13 Specifications GENERAL Operating T emperature -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Pan/T ilt Adjustment Manual; 360° pan; 180° tilt Construction Aluminum with steel camera mounting bracket and poly carbonate dome Finish White polyester powder coat trim ring with charcoal gray back box Dimensions Refer to d ...
-
Pelco C2410M-1 - page 14
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series p ...
-
Pelco C2410M-1 - page 15
REVISION HISTORY Manual # Date Comments C2410M 11/99 Original version. C2410M 1/00 Revised installation instructions. Added FCC notices. C2410M-A 1/00 Added varifocal lens. Changed format. C2410M-B 7/00 Added information on dome liner. C2410M-C 1/01 Added heater element caution. C2410M-D 7/01 Camera module redesigned, reference ECO 1-7054/7055/7056 ...
-
Pelco C2410M-1 - page 16
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...
¿Tienes una pregunta acerca de Pelco C2410M-1?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pelco C2410M-1, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pelco C2410M-1 probablemente compartirá una forma de solucionarlo.