-
Windsor E50 - page 1
Read these instructions bef ore operating the machine MOD EL: E50 98635 01/09/07 U CARPET EXTRACTOR Operating Instru ctions (ENG ) ...
-
Windsor E50 - page 2
MACHINE DATA LOG/OVERVIEW ENSIGN 98635 04/04/03 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: __________________________________________________________________________________________________ Address: _______________________________________________________________________________________________ Phone Numb ...
-
Windsor E50 - page 3
TABLE OF CONTENTS ENSIGN 98635 03/26/04 3 Machine Data Log/Overview. ......................... 1 Table of Contents ........................................... 2 HOW TO USE THIS MANUAL How to use this Manual. ................................ 1-1 SAFETY Important Safety Instructions ........................ 2-1 Hazard Intensity Level. ............... ...
-
Windsor E50 - page 4
HOW TO USE THIS MANUAL ENSIGN 98635 04/04/03 1-1 This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized Windsor dealers. When placi ...
-
Windsor E50 - page 5
SAFETY INSTRUCTIONS ENSIGN 98635 04/04/03 2 -1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded ...
-
Windsor E50 - page 6
HAZARD INTENSITY LEVEL ENSIGN 98635 04/04/03 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING ...
-
Windsor E50 - page 7
SAFETY LABEL LOCATION ENSIGN 98635 04/04/03 2-3 NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. LABEL WARNING 500009 ...
-
Windsor E50 - page 8
GROUNDING INSTRUCTIONS ENSIGN 98635 04/04/03 2-4 THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a standard 15 amp 115V, 60 hz, A.C. power circuit . The amp , hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause seri ...
-
Windsor E50 - page 9
TECHNICAL SPECIFICATIONS ENSIGN 98635 04/04/03 3-1 ITEM MEASURE Electrical 115 Volt, 60hz Vacuum Motor Single 3 stage Solution Pump 50 psi Solution Capacity 7 gal (26 L) Recovery Capacity 6 gal (22 L) Weight - Empty 50 lbs (110 kg) Weight –Full Solution 105 lbs (230 kg) Height 35 inches (88.90 cm) Height – (Handle Folded Down) 28.5 inches (72.3 ...
-
Windsor E50 - page 10
CONTROLS ENSIGN 98635 04/04/03 3-2 1. Vacuum Switch 2. Pump Switch ON OFF OFF ON VAC PUMP 1 2 ...
-
Windsor E50 - page 11
MACHINE OPERATION ENSIGN 98635 04/04/03 3-3 GENERAL INFORMATION As the carpet is being cleaned, check to see if there is foam building up in the recovery bucket. Add a little defoaming compound to the recovery tank but never to the solution tank. For infrequent use or long periods of storage , flush the system with a neutralizing solution of 1 quar ...
-
Windsor E50 - page 12
MAINTENANCE ENSIGN 98635 04/04/03 4-1 Unplug power cord(s) before servicing or making any repairs . DAILY MAINTENANCE 1. Flush the entire system, including floor tool, hand tool, etc., with 1 to 3 gallons of clean, hot water. 2. Vacuum out the solution tank. 3. Rinse tank with fresh water. Periodically inspect the recovery tank and decontaminate if ...
-
Windsor E50 - page 13
MAINTENANCE ENSIGN 98635 03/26/04 4-2 Only qualified maintenance personnel are to perform the following repairs . VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Locate the vacuum motor wires and disconnect at the connector. 4. Remove the vacuum motor. 5. Reverse process to install vacuum motor. Vac ...
-
Windsor E50 - page 14
MAINTENANCE ENSIGN 98635 03/26/04 4-3 Only qualified maintenance personnel are to perform the following repairs . SOLUTION PUMP REPLACEMENT 1. Turn off all switches and unplug the machine. 2. Remove recovery tank. 3. Remove solution hoses from fittings in pump. 4. Remove the screws that fasten the pump to the frame. 5. Reverse process to install pu ...
-
Windsor E50 - page 15
TROUBLESHOOTING ENSIGN 98635 03/26/04 4-4 PROBLEM CAUSE SOLUTION Dead electrical circuit Check building circuit breaker or fuse box. Loss of Power Faulty power cord Replace Equipment not grounding Follow grounding instructions exactly Receptacle not grounded Contact an electrician to check building’s wiring Electrical shock Internal wiring proble ...
-
Windsor E50 - page 16
PUMP GROUP ENSIGN 98635 04/04/03 5-1 1 2 3 5 6 7 8 2 3 4 ...
-
Windsor E50 - page 17
PUMP GROUP ENSIGN 98635 01/09/07 5-2 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 39049 1 HOSE, 3/8” RUBBER X 11’ 2 20042 2 CLAMP, 3/8 HOSE (D-SLOT) 3 40043 2 HOSEBARB, 3/8 MPT X 3/8 90 ° 4 65216 1 PUMP ASM, 115V 3ST SENSEI 5 110-22 4 GROMMET 6 GAL. PORT 6 87013 2 WASHER, 1/4 ID X 5/8 OD SS 7 70020 2 SCR, 1/4-20 X 1/2 HHCS SS NP 8 393 ...
-
Windsor E50 - page 18
RECOVERY TANK GROUP ENSIGN 98635 03/18/05 5 - 3 3 4 5 6 9 10 11 12 14 16 17 18 20 21 22 23 24 13 15 26 15 1 27 7 8 19 2 32 25 28 29 30 31 ...
-
Windsor E50 - page 19
RECOVERY TANK GROUP ENSIGN 98635 03/18/05 5 - 4 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 04094 1 ADPTR, 1.5FS X 1.5FS PVC “U” 2 34408 1 FLOAT SHUT - OFF TUBE W/ADPTR 3 260 - 64A 1 ACCESS COVER CLEAR 6” W/ RIM 4 70546 6 SCR, 8 X 3/4 PFHT/S BLK ZINC 5 38299 1 HANDLE, DK GRY 6 110 - 14B 2 CAP PLUG 5/8” 7 57106 3 NUT, 8 - 32 W/STAR ...
-
Windsor E50 - page 20
SOLUTION TANK GROUP ENSIGN 98635 01/09/07 5-5 * * PARTS INSIDE TANK CONNECT TO PUMP ASM 4 5 7 8 6 6 1 2 9 10 41 6 11 12 6 14 13 15 18 19 22 20 21 17 16 23 24 28 29 30 18 31 32 33 34 35 38 37 39 39 40 36 3 26 27 25 23 42 43 ...
-
Windsor E50 - page 21
SOLUTION TANK GROUP ENSIGN 98635 01/09/07 5-6 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 56012 1 NIPPLE, 1/4FPT QD 2 87015 1 WASHER, 9/16 ID X 1.06 OD SS 3 86014060 1 TANK, SOLUTION SENSEI BLK 4 030-16 1 ELBOW, 1/4 NPT STREET LONG 90D 5 40014 1 HOSEBARB, 1/4MPT X 3/8 BRASS DL 6 20042 4 CLAMP, 3/8 HOSE (D-SLOT) 7 39311 1 HOSE, 3/8 RUBBER ...
-
Windsor E50 - page 22
VACUUM MOTOR GROUP ENSIGN 98635 04/04/03 5-7 3 1 2 4 5 ...
-
Windsor E50 - page 23
VACUUM MOTOR GROUP ENSIGN 98635 03/26/04 5-8 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 065-24E 3 VAC SPACER 3 1/8 2 87013 3 WASHER, 1/4 ID X 5/8 OD SS 3 70062 3 SCR, 1/4-20 X 4 HHCS GR5 PLTD 4 53130 1 VAC MOTOR, 120V 5.7 3ST W/O TB * - 140687 - BRUSH SET,120V VAC WINDSOR * SERVICE ONLY - 140676 - BRUSH SET, 120V 3ST VAC AMETEK SERVICE O ...
-
Windsor E50 - page 24
WIRING DIAGRAM ENSIGN 98635 04/04/03 5-9 ...
-
Windsor E50 - page 25
SUGGESTED SPARE PARTS ENSIGN 98635 03/26/04 5-10 PART NO. DESCRIPTION SERIAL NO. FROM NOTES: 34380 FLOAT SHUT OFF 260-64A ACCESS COVER CLEAR 6” W/RIM 11-800444 ELBOW, 1.5 FS X FS 45D PVC 72142 SWITCH SPST 15A EURO ROCKER 320-05 VELCRO STRAPS 35011 GASKET, 3/8T 5.7 VAC FAN SEAL 140-12 KNOB 1/4-20 X 3/4 S/S CUPPOINT 140687 BRUSH SET, 120V VAC WINDS ...
-
Windsor E50 - page 26
NOTES ENSIGN 98635 04/04/03 5-11 ...
¿Tienes una pregunta acerca de Windsor E50?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Windsor E50, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Windsor E50 probablemente compartirá una forma de solucionarlo.