Windsor E50の取扱説明書

26ページ 0.66 mb
ダウンロード

ページに移動 of 26

Summary
  • Windsor E50 - page 1

    Read these instructions bef ore operating the machine MOD EL: E50 98635 01/09/07 U CARPET EXTRACTOR Operating Instru ctions (ENG ) ...

  • Windsor E50 - page 2

    MACHINE DATA LOG/OVERVIEW ENSIGN 98635 04/04/03 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: __________________________________________________________________________________________________ Address: _______________________________________________________________________________________________ Phone Numb ...

  • Windsor E50 - page 3

    TABLE OF CONTENTS ENSIGN 98635 03/26/04 3 Machine Data Log/Overview. ......................... 1 Table of Contents ........................................... 2 HOW TO USE THIS MANUAL How to use this Manual. ................................ 1-1 SAFETY Important Safety Instructions ........................ 2-1 Hazard Intensity Level. ............... ...

  • Windsor E50 - page 4

    HOW TO USE THIS MANUAL ENSIGN 98635 04/04/03 1-1 This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized Windsor dealers. When placi ...

  • Windsor E50 - page 5

    SAFETY INSTRUCTIONS ENSIGN 98635 04/04/03 2 -1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded ...

  • Windsor E50 - page 6

    HAZARD INTENSITY LEVEL ENSIGN 98635 04/04/03 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING ...

  • Windsor E50 - page 7

    SAFETY LABEL LOCATION ENSIGN 98635 04/04/03 2-3 NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. LABEL WARNING 500009 ...

  • Windsor E50 - page 8

    GROUNDING INSTRUCTIONS ENSIGN 98635 04/04/03 2-4 THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a standard 15 amp 115V, 60 hz, A.C. power circuit . The amp , hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause seri ...

  • Windsor E50 - page 9

    TECHNICAL SPECIFICATIONS ENSIGN 98635 04/04/03 3-1 ITEM MEASURE Electrical 115 Volt, 60hz Vacuum Motor Single 3 stage Solution Pump 50 psi Solution Capacity 7 gal (26 L) Recovery Capacity 6 gal (22 L) Weight - Empty 50 lbs (110 kg) Weight –Full Solution 105 lbs (230 kg) Height 35 inches (88.90 cm) Height – (Handle Folded Down) 28.5 inches (72.3 ...

  • Windsor E50 - page 10

    CONTROLS ENSIGN 98635 04/04/03 3-2 1. Vacuum Switch 2. Pump Switch ON OFF OFF ON VAC PUMP 1 2 ...

  • Windsor E50 - page 11

    MACHINE OPERATION ENSIGN 98635 04/04/03 3-3 GENERAL INFORMATION As the carpet is being cleaned, check to see if there is foam building up in the recovery bucket. Add a little defoaming compound to the recovery tank but never to the solution tank. For infrequent use or long periods of storage , flush the system with a neutralizing solution of 1 quar ...

  • Windsor E50 - page 12

    MAINTENANCE ENSIGN 98635 04/04/03 4-1 Unplug power cord(s) before servicing or making any repairs . DAILY MAINTENANCE 1. Flush the entire system, including floor tool, hand tool, etc., with 1 to 3 gallons of clean, hot water. 2. Vacuum out the solution tank. 3. Rinse tank with fresh water. Periodically inspect the recovery tank and decontaminate if ...

  • Windsor E50 - page 13

    MAINTENANCE ENSIGN 98635 03/26/04 4-2 Only qualified maintenance personnel are to perform the following repairs . VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Locate the vacuum motor wires and disconnect at the connector. 4. Remove the vacuum motor. 5. Reverse process to install vacuum motor. Vac ...

  • Windsor E50 - page 14

    MAINTENANCE ENSIGN 98635 03/26/04 4-3 Only qualified maintenance personnel are to perform the following repairs . SOLUTION PUMP REPLACEMENT 1. Turn off all switches and unplug the machine. 2. Remove recovery tank. 3. Remove solution hoses from fittings in pump. 4. Remove the screws that fasten the pump to the frame. 5. Reverse process to install pu ...

  • Windsor E50 - page 15

    TROUBLESHOOTING ENSIGN 98635 03/26/04 4-4 PROBLEM CAUSE SOLUTION Dead electrical circuit Check building circuit breaker or fuse box. Loss of Power Faulty power cord Replace Equipment not grounding Follow grounding instructions exactly Receptacle not grounded Contact an electrician to check building’s wiring Electrical shock Internal wiring proble ...

  • Windsor E50 - page 16

    PUMP GROUP ENSIGN 98635 04/04/03 5-1 1 2 3 5 6 7 8 2 3 4 ...

  • Windsor E50 - page 17

    PUMP GROUP ENSIGN 98635 01/09/07 5-2 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 39049 1 HOSE, 3/8” RUBBER X 11’ 2 20042 2 CLAMP, 3/8 HOSE (D-SLOT) 3 40043 2 HOSEBARB, 3/8 MPT X 3/8 90 ° 4 65216 1 PUMP ASM, 115V 3ST SENSEI 5 110-22 4 GROMMET 6 GAL. PORT 6 87013 2 WASHER, 1/4 ID X 5/8 OD SS 7 70020 2 SCR, 1/4-20 X 1/2 HHCS SS NP 8 393 ...

  • Windsor E50 - page 18

    RECOVERY TANK GROUP ENSIGN 98635 03/18/05 5 - 3 3 4 5 6 9 10 11 12 14 16 17 18 20 21 22 23 24 13 15 26 15 1 27 7 8 19 2 32 25 28 29 30 31 ...

  • Windsor E50 - page 19

    RECOVERY TANK GROUP ENSIGN 98635 03/18/05 5 - 4 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 04094 1 ADPTR, 1.5FS X 1.5FS PVC “U” 2 34408 1 FLOAT SHUT - OFF TUBE W/ADPTR 3 260 - 64A 1 ACCESS COVER CLEAR 6” W/ RIM 4 70546 6 SCR, 8 X 3/4 PFHT/S BLK ZINC 5 38299 1 HANDLE, DK GRY 6 110 - 14B 2 CAP PLUG 5/8” 7 57106 3 NUT, 8 - 32 W/STAR ...

  • Windsor E50 - page 20

    SOLUTION TANK GROUP ENSIGN 98635 01/09/07 5-5 * * PARTS INSIDE TANK CONNECT TO PUMP ASM 4 5 7 8 6 6 1 2 9 10 41 6 11 12 6 14 13 15 18 19 22 20 21 17 16 23 24 28 29 30 18 31 32 33 34 35 38 37 39 39 40 36 3 26 27 25 23 42 43 ...

  • Windsor E50 - page 21

    SOLUTION TANK GROUP ENSIGN 98635 01/09/07 5-6 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 56012 1 NIPPLE, 1/4FPT QD 2 87015 1 WASHER, 9/16 ID X 1.06 OD SS 3 86014060 1 TANK, SOLUTION SENSEI BLK 4 030-16 1 ELBOW, 1/4 NPT STREET LONG 90D 5 40014 1 HOSEBARB, 1/4MPT X 3/8 BRASS DL 6 20042 4 CLAMP, 3/8 HOSE (D-SLOT) 7 39311 1 HOSE, 3/8 RUBBER ...

  • Windsor E50 - page 22

    VACUUM MOTOR GROUP ENSIGN 98635 04/04/03 5-7 3 1 2 4 5 ...

  • Windsor E50 - page 23

    VACUUM MOTOR GROUP ENSIGN 98635 03/26/04 5-8 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 065-24E 3 VAC SPACER 3 1/8 2 87013 3 WASHER, 1/4 ID X 5/8 OD SS 3 70062 3 SCR, 1/4-20 X 4 HHCS GR5 PLTD 4 53130 1 VAC MOTOR, 120V 5.7 3ST W/O TB * - 140687 - BRUSH SET,120V VAC WINDSOR * SERVICE ONLY - 140676 - BRUSH SET, 120V 3ST VAC AMETEK SERVICE O ...

  • Windsor E50 - page 24

    WIRING DIAGRAM ENSIGN 98635 04/04/03 5-9 ...

  • Windsor E50 - page 25

    SUGGESTED SPARE PARTS ENSIGN 98635 03/26/04 5-10 PART NO. DESCRIPTION SERIAL NO. FROM NOTES: 34380 FLOAT SHUT OFF 260-64A ACCESS COVER CLEAR 6” W/RIM 11-800444 ELBOW, 1.5 FS X FS 45D PVC 72142 SWITCH SPST 15A EURO ROCKER 320-05 VELCRO STRAPS 35011 GASKET, 3/8T 5.7 VAC FAN SEAL 140-12 KNOB 1/4-20 X 3/4 S/S CUPPOINT 140687 BRUSH SET, 120V VAC WINDS ...

  • Windsor E50 - page 26

    NOTES ENSIGN 98635 04/04/03 5-11 ...

メーカー Windsor カテゴリー Automobile Accessories

Windsor E50のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- E50の取扱説明書
- Windsorの製品カード
- パンフレット
- またはWindsor E50の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Windsor E50の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Windsor E50の取り付け説明書、サービスマニュアル、簡易説明書、またはWindsor E50のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Windsor E50の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Windsor E50デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWindsor E50を使用するのを助ける技術的文書のことです。説明書は通常、全てのWindsor E50ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Windsorの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Windsor E50の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWindsor E50の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Windsor E50に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Windsor E50デバイスの基本機能を使うにあたってのヒント。 Windsor E50のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Windsor E50に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWindsor E50のメーカー/サービスへの連絡先に関する情報。

Windsor E50についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWindsor E50の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWindsor E50で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (1)

Юрий

Здравствуйте! Молу ли я получить мануал на русском языке для Studiologic VMK-188 Plus? Меня интересует раздел клавиатуры на зоны. Спасибо заранее.