-
Cadillac 2000 - page 1
2000 Cadillac D e Ville Outer Wheelhouse Sectioning 1-12 Inner Front Pillar Sectioning 1-9 Inner Center Pillar Sectioning 1-10 Outer Front Pillar Sectioning 1-2 Outer Center Pillar Sectioning 1-4 Rear Rail Sectioning 1-13 Quarter P anel Sectioning 1-6 Body Dimensions 1-17/18 ...
-
Cadillac 2000 - page 2
2000 cadillac deville 1-1 Outer Front Pillar , Center Pillar and Quarter Panel Sectioning CAUTION: When performing service on or near the Supplemental Inflatable Restraint (SIR) components or the SIR wiring, the SIR system must be disabled. Failure to follow the correct procedure could cause air bag deployment, personal injury or unnecessary SIR sy ...
-
Cadillac 2000 - page 3
Outer Front Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Visually inspect and restore as much of the damage as possible to factory specifications. 2. Remove the following: • Fender • Windshield • Door • ...
-
Cadillac 2000 - page 4
Installation Procedure IMPORTANT: Remove all foam prior to welding this section of the service panel. 1. Prepare mating surfaces. 2. Apply weld-through primer to mating surfaces prior to assembly. 3. Weld backing plates to vehicle at rocker. IMPORTANT: Replace hinge pillar blocks prior to welding outer panel. 4. Apply windshield bonding adhesive to ...
-
Cadillac 2000 - page 5
Outer Center Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Locate an approved sectioning area in the center pillar (Fig.␣ 1-5). 2. Mark and scribe a line. This is the cut location. 3. Cut Center Pillar at cut ...
-
Cadillac 2000 - page 6
Installation Procedure 1. Install sleeves on vehicle at rocker and center pillar areas using plug welds. 2. Replace hinge blocks and bolts. 3. Prepare mating surfaces. IMPORTANT: Prior to refinishing, refer to the publication GM4901M-D-2000 “GM Approved Refinish Materials” for recommended products. Do not combine paint systems. Refer to paint m ...
-
Cadillac 2000 - page 7
1-6 2000 cadillac deville Quarter Panel Sectioning Removal Procedure The service part comes with lower quarter panel extension and taillamp pocket attached. These parts can be left on the vehicle if not damaged. Drill out factory welds on the car and service part and use the outer panel only. IMPORTANT: When replacing panels that involve servicing ...
-
Cadillac 2000 - page 8
2000 cadillac deville 1-7 Preparation Of Service Part 1. Cut service part in corresponding locations to fit original cut lines. Leave a gap of one-and- one-half times the metal thickness of sectioning joint (Fig. 1-9). 2. Create 100␣ mm (4␣ in) backing plate on rocker panel from unused portion of service part. 3. Create a 50␣ mm (2␣ in) bac ...
-
Cadillac 2000 - page 9
1-8 2000 cadillac deville Inner Front Pillar , Center Pillar and Rear Wheelhouse Sectioning Fig.␣ 1-11 — 2000 DeVille Inner Frame Sectioning Locations CAUTION: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Failure to follow the correct procedure could cause air bag deployment, personal ...
-
Cadillac 2000 - page 10
2000 cadillac deville 1-9 Inner Front Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Visually inspect and restore as much of the damage as possible to factory specifications. 2. Remove outer panel according to sp ...
-
Cadillac 2000 - page 11
1-10 2000 cadillac deville Installation Procedure 1. Prepare mating surfaces. IMPORTANT: Prior to refinishing, refer to the publication GM4901M-D-2000 “GM Approved Refinish Materials” for recommended products. Do not combine paint systems. Refer to paint manufacturer’s recommendations. 2. Prime with two-part catalyzed primer. 3. Position part ...
-
Cadillac 2000 - page 12
2000 cadillac deville 1-11 Preparation of Service Part 1. Cut center pillar at laser weld location. This will allow a 25␣ mm (1␣ in) overlap to the vehicle for welding (Fig. 1-16). 2. Notch the weather strip flange to prevent excessive metal thickness in these areas. 3. In front and rear door rocker areas of service part, scribe vertical cut li ...
-
Cadillac 2000 - page 13
1-12 2000 cadillac deville Outer Wheelhouse Sectioning Removal Procedure 1. Locate horizontal laser-weld line in upper quarter area (Fig. 1-18). 2. Measure down 25␣ mm (1␣ in) and scribe a cut line. 3. On the vehicle rocker area, locate and scribe a vertical cut line in the recommended section area. 4. Cut panel at scribed locations. 5. Drill o ...
-
Cadillac 2000 - page 14
2000 cadillac deville 1-13 Rear Rail Sectioning The rear rail is available as a complete assembly. It consists of an outer panel, two inner reinforcements, a rail extension, and all necessary component mounting brackets (Fig. 1-20). The outer panel and rear mounting brackets are also available separately to facilitate sectioning. Additionally, ther ...
-
Cadillac 2000 - page 15
1-14 2000 cadillac deville Removal Procedure 1. Visually inspect and restore as much of the damage as possible to factory specifications. 2. Remove all related panels and components. 3. Cut the rear rail along the rearward flange of the crossbar (Fig. 1-21). Continue this cut around the rear rail. 4. Drill out the factory welds on the end of the re ...
-
Cadillac 2000 - page 16
2000 cadillac deville 1-15 Installation Procedure 1. Using the original part as a guide, mark a line on the service rail 35␣ mm (1-5/16␣ in) forward of the cut made to the original part; this should be approximately 535␣ mm (21␣ in) without the extension attached to the rail. This will provide an overlap for welding the service section (see ...
-
Cadillac 2000 - page 17
1-16 2000 cadillac deville ZERO LINE A B C D E F ALL LENGTHS MEASURED FROM Ø LINE AT TOP HINGE 19 MM HOLE ALL MEASUREMENTS HOLE CENTER TO CENTER 19 MM GAGE HOLE Ø Engine Compartment Dimensions – 2000 Cadillac DeV ille Description Location Length Width Height Strut mount hole A 367 565 1014 Strut mount hole B 509 575 1029 Strut mount hole C 437 ...
-
Cadillac 2000 - page 18
2000 cadillac deville 1-17 Ø C A B D E F G 540 469 552 526 925 888 1752 2537 3191 1092 348 358 537 496 504 427 430 496 553 577 D A TUM LINE WIDTH HEIGHT LENGTH Underbody Dimensions – 2000 Cadillac DeV ille Description Location Length Width Height 28 mm mounting nut A 1092 540 469 19 mm x 25 mm gage slot B 925 504 552 16 mm gage hole C 0 427 526 ...
-
Cadillac 2000 - page 19
1-18 2000 cadillac deville ø A B C D E F D A TUM LINE 829 840 827 836 0 0 1140 1140 2183 849 591 930 964 665 1004 WIDTH HEIGHT LENGTH Body Side Dimensions – 2000 Cadillac DeV ille Description Location Length Width Height 19 mm gage hole A 0 — — 19 mm gage hole B 0 836 591 19 mm gage hole C 0 829 930 19 mm gage hole D 1140 840 964 Lower hinge ...
¿Tienes una pregunta acerca de Cadillac 2000?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cadillac 2000, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cadillac 2000 probablemente compartirá una forma de solucionarlo.