Cadillac 2000の取扱説明書

19ページ 0.35 mb
ダウンロード

ページに移動 of 19

Summary
  • Cadillac 2000 - page 1

    2000 Cadillac D e Ville Outer Wheelhouse Sectioning 1-12 Inner Front Pillar Sectioning 1-9 Inner Center Pillar Sectioning 1-10 Outer Front Pillar Sectioning 1-2 Outer Center Pillar Sectioning 1-4 Rear Rail Sectioning 1-13 Quarter P anel Sectioning 1-6 Body Dimensions 1-17/18 ...

  • Cadillac 2000 - page 2

    2000 cadillac deville 1-1 Outer Front Pillar , Center Pillar and Quarter Panel Sectioning CAUTION: When performing service on or near the Supplemental Inflatable Restraint (SIR) components or the SIR wiring, the SIR system must be disabled. Failure to follow the correct procedure could cause air bag deployment, personal injury or unnecessary SIR sy ...

  • Cadillac 2000 - page 3

    Outer Front Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Visually inspect and restore as much of the damage as possible to factory specifications. 2. Remove the following: • Fender • Windshield • Door • ...

  • Cadillac 2000 - page 4

    Installation Procedure IMPORTANT: Remove all foam prior to welding this section of the service panel. 1. Prepare mating surfaces. 2. Apply weld-through primer to mating surfaces prior to assembly. 3. Weld backing plates to vehicle at rocker. IMPORTANT: Replace hinge pillar blocks prior to welding outer panel. 4. Apply windshield bonding adhesive to ...

  • Cadillac 2000 - page 5

    Outer Center Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Locate an approved sectioning area in the center pillar (Fig.␣ 1-5). 2. Mark and scribe a line. This is the cut location. 3. Cut Center Pillar at cut ...

  • Cadillac 2000 - page 6

    Installation Procedure 1. Install sleeves on vehicle at rocker and center pillar areas using plug welds. 2. Replace hinge blocks and bolts. 3. Prepare mating surfaces. IMPORTANT: Prior to refinishing, refer to the publication GM4901M-D-2000 “GM Approved Refinish Materials” for recommended products. Do not combine paint systems. Refer to paint m ...

  • Cadillac 2000 - page 7

    1-6 2000 cadillac deville Quarter Panel Sectioning Removal Procedure The service part comes with lower quarter panel extension and taillamp pocket attached. These parts can be left on the vehicle if not damaged. Drill out factory welds on the car and service part and use the outer panel only. IMPORTANT: When replacing panels that involve servicing ...

  • Cadillac 2000 - page 8

    2000 cadillac deville 1-7 Preparation Of Service Part 1. Cut service part in corresponding locations to fit original cut lines. Leave a gap of one-and- one-half times the metal thickness of sectioning joint (Fig. 1-9). 2. Create 100␣ mm (4␣ in) backing plate on rocker panel from unused portion of service part. 3. Create a 50␣ mm (2␣ in) bac ...

  • Cadillac 2000 - page 9

    1-8 2000 cadillac deville Inner Front Pillar , Center Pillar and Rear Wheelhouse Sectioning Fig.␣ 1-11 — 2000 DeVille Inner Frame Sectioning Locations CAUTION: When performing service on or near the SIR components or the SIR wiring, the SIR system must be disabled. Failure to follow the correct procedure could cause air bag deployment, personal ...

  • Cadillac 2000 - page 10

    2000 cadillac deville 1-9 Inner Front Pillar Sectioning Removal Procedure IMPORTANT: Sectioning should be performed only in the recommended areas. Failure to do so may compromise the structural integrity of the vehicle. 1. Visually inspect and restore as much of the damage as possible to factory specifications. 2. Remove outer panel according to sp ...

  • Cadillac 2000 - page 11

    1-10 2000 cadillac deville Installation Procedure 1. Prepare mating surfaces. IMPORTANT: Prior to refinishing, refer to the publication GM4901M-D-2000 “GM Approved Refinish Materials” for recommended products. Do not combine paint systems. Refer to paint manufacturer’s recommendations. 2. Prime with two-part catalyzed primer. 3. Position part ...

  • Cadillac 2000 - page 12

    2000 cadillac deville 1-11 Preparation of Service Part 1. Cut center pillar at laser weld location. This will allow a 25␣ mm (1␣ in) overlap to the vehicle for welding (Fig. 1-16). 2. Notch the weather strip flange to prevent excessive metal thickness in these areas. 3. In front and rear door rocker areas of service part, scribe vertical cut li ...

  • Cadillac 2000 - page 13

    1-12 2000 cadillac deville Outer Wheelhouse Sectioning Removal Procedure 1. Locate horizontal laser-weld line in upper quarter area (Fig. 1-18). 2. Measure down 25␣ mm (1␣ in) and scribe a cut line. 3. On the vehicle rocker area, locate and scribe a vertical cut line in the recommended section area. 4. Cut panel at scribed locations. 5. Drill o ...

  • Cadillac 2000 - page 14

    2000 cadillac deville 1-13 Rear Rail Sectioning The rear rail is available as a complete assembly. It consists of an outer panel, two inner reinforcements, a rail extension, and all necessary component mounting brackets (Fig. 1-20). The outer panel and rear mounting brackets are also available separately to facilitate sectioning. Additionally, ther ...

  • Cadillac 2000 - page 15

    1-14 2000 cadillac deville Removal Procedure 1. Visually inspect and restore as much of the damage as possible to factory specifications. 2. Remove all related panels and components. 3. Cut the rear rail along the rearward flange of the crossbar (Fig. 1-21). Continue this cut around the rear rail. 4. Drill out the factory welds on the end of the re ...

  • Cadillac 2000 - page 16

    2000 cadillac deville 1-15 Installation Procedure 1. Using the original part as a guide, mark a line on the service rail 35␣ mm (1-5/16␣ in) forward of the cut made to the original part; this should be approximately 535␣ mm (21␣ in) without the extension attached to the rail. This will provide an overlap for welding the service section (see ...

  • Cadillac 2000 - page 17

    1-16 2000 cadillac deville ZERO LINE A B C D E F ALL LENGTHS MEASURED FROM Ø LINE AT TOP HINGE 19 MM HOLE ALL MEASUREMENTS HOLE CENTER TO CENTER 19 MM GAGE HOLE Ø Engine Compartment Dimensions – 2000 Cadillac DeV ille Description Location Length Width Height Strut mount hole A 367 565 1014 Strut mount hole B 509 575 1029 Strut mount hole C 437 ...

  • Cadillac 2000 - page 18

    2000 cadillac deville 1-17 Ø C A B D E F G 540 469 552 526 925 888 1752 2537 3191 1092 348 358 537 496 504 427 430 496 553 577 D A TUM LINE WIDTH HEIGHT LENGTH Underbody Dimensions – 2000 Cadillac DeV ille Description Location Length Width Height 28 mm mounting nut A 1092 540 469 19 mm x 25 mm gage slot B 925 504 552 16 mm gage hole C 0 427 526 ...

  • Cadillac 2000 - page 19

    1-18 2000 cadillac deville ø A B C D E F D A TUM LINE 829 840 827 836 0 0 1140 1140 2183 849 591 930 964 665 1004 WIDTH HEIGHT LENGTH Body Side Dimensions – 2000 Cadillac DeV ille Description Location Length Width Height 19 mm gage hole A 0 — — 19 mm gage hole B 0 836 591 19 mm gage hole C 0 829 930 19 mm gage hole D 1140 840 964 Lower hinge ...

メーカー Cadillac カテゴリー Automobile

Cadillac 2000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2000の取扱説明書
- Cadillacの製品カード
- パンフレット
- またはCadillac 2000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cadillac 2000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cadillac 2000の取り付け説明書、サービスマニュアル、簡易説明書、またはCadillac 2000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cadillac 2000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cadillac 2000デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCadillac 2000を使用するのを助ける技術的文書のことです。説明書は通常、全てのCadillac 2000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cadillacの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cadillac 2000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCadillac 2000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cadillac 2000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cadillac 2000デバイスの基本機能を使うにあたってのヒント。 Cadillac 2000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cadillac 2000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCadillac 2000のメーカー/サービスへの連絡先に関する情報。

Cadillac 2000についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCadillac 2000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCadillac 2000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (1)

Heidi

I am looking at purchasing the audio line AB 871 answering machine and just wanted to know how it works, can it work being attached to a hands free device, do you first plug it into the telephone line and then attach receiver to it?