-
Sears 200.71234 - page 1
Sears, Roebuck and Co., Hoffman Est ates, IL 60179 U.S.A. B A TTER Y CHARGER 60/20/2 Amp Fully A utomatic 275/125 AMP ENGINE ST AR TER With Batter y T ester and GFCI Outlets Model No. 200.71234 O WNER’S MANU AL 00-99-000539/0206 CA UTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product. ® ...
-
Sears 200.71234 - page 2
1 W arranty .................................................................... 1 Important Safety Instructions ................................. 2 P arts .......................................................................... 3 Wiring Diagram ........................................................ 3 Before Using Y our Batter y Charger ....... ...
-
Sears 200.71234 - page 3
2 Help us help you Remember: • Place charger as far away from battery being charged as the charger cables will permit. • Do not expose charger to rain or snow. • Never charge a frozen battery. If battery fluid (electrolyte) becomes frozen, bring battery into a warm area to thaw before you begin charging. • Never allow battery acid to drip o ...
-
Sears 200.71234 - page 4
3 Pa r t s This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Wiring Diagram Replacement Parts List DieHard 71234 ITEM DESCRIPTION PART NUMBER 1 Plastic Top 3799004100 2 Rocker Switch SPST 0499000050 3 Rocker Switch DPDT 0499000053 4 Control Board Asse ...
-
Sears 200.71234 - page 5
4 Attach Foot: Remove charger from packing materials and place charger on its side. Attach mounting foot and secure with the two, 1/4-20 thread cutting screws provided. continued on next page Before Using Y our Battery Charger It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect ...
-
Sears 200.71234 - page 6
5 Axle Assembly (continued): Place the charger on its side. Place one end of each bracket into slot, then place the axle assembly under each bracket. Fasten the other side of each bracket using the two, 10-32 thread cutting screws provided. Handle: Turn the charger right side up onto its foot and wheels. Remove the two top screws from each side of ...
-
Sears 200.71234 - page 7
6 MINIMUM RECOMMENDED EXTENSION CORD Length of Cord, in Feet 25 50 100 150 AWG* Size of Cord 14 12 10 8 *AWG=American Wire Gauge P reparing your battery to be charged It is important that you read and follow these guide- lines while you are preparing to charge your battery. • Make sure that you have a 12 volt or 6 volt lead-acid battery. Set the ...
-
Sears 200.71234 - page 8
7 For best results from your battery charger, learn to use it properly. This section tells how to set the controls, charge a battery in or out of the vehicle, use the ENGINE START feature and test the battery. Using Y our Battery Charger All the controls for your charger are located on the front. Follow these instructions to obtain the accurate cha ...
-
Sears 200.71234 - page 9
8 • TIME: To select a charging time, you must be in the MANUAL mode and have selected a charge rate. Touch the TIME pad until the desired time shows on the meter. The following chart shows the amount of time available for each charge rate and the amount of time, in hours, added for each touch of the TIME pad. RATE 2 Amps 20 Amps 60 Amps Maximum 1 ...
-
Sears 200.71234 - page 10
9 Charging Y our Battery NO TE: A marine (boat) boat batter y must be remov ed and charged on shore. T o charge it on board requires equipment specially designed for marine use. Charging your battery in the vehicle: 1. Arrange the power cord and charging leads carefully in order to avoid damage that could be caused by the hood, door, or moving engi ...
-
Sears 200.71234 - page 11
10 8. For automatic charging, touch AUTO then a charge-rate pad 2, 20, or 60 Amps. The charging will stop when the battery is fully charged. 9. For manual charging, touch a charge rate pad then select a charge time up to 18 hours. If more than 18 hours of charging time is needed, reset the time when the original time runs out. Refer to the Time Cha ...
-
Sears 200.71234 - page 12
11 Calculating charge times • Marine, or deep-cycle batteries are usually rated in Reserve Capacity (RC) . • NR means that the charger setting is NOT RECOM- MENDED . Find your battery’s rating on the chart below and note the charge time given for each charger setting. The times given are for batteries with a 50-percent charge prior to recharg ...
-
Sears 200.71234 - page 13
12 A minimal amount of care can keep your battery charger working properly for years. 1. Clean the clamps each time you are finished charging. Wipe off any battery fluid that may have come in contact with the clamps to prevent corrosion. 2. Coil the input and output cords neatly when storing the charger. The cords can be wrapped around the handle o ...
-
Sears 200.71234 - page 14
13 T roubleshooting Performance problems often result from little things that you can fix yourself. Please read through this table for a possible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No reading on the Clamps are not making a Check f or poor connections at batter y and frame. Make Displa y . good connection. sure con ...
-
Sears 200.71234 - page 15
14 For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm Central Time Monday through Friday. 1-800-SEARS-64 (1-800-732-7764). ...
¿Tienes una pregunta acerca de Sears 200.71234?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sears 200.71234, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sears 200.71234 probablemente compartirá una forma de solucionarlo.