Español dropdown-ico

Manual de instrucciones Lincoln Electric IM573

32 de páginas 1.51 mb
Descargar

Pasar a la página of 32

Summary
  • Lincoln Electric IM573 - page 1

    CALIBRA TION PROCEDURES IM573 September , 2002 PO WER W A VE PC BOARD REPLA CEMENT CALIBRA TION PROCEDURES Safety Depends on Y ou Lincoln arc welding and cutting equipment is designed and built with safety in mind. However , your overall safety can be increased by pr oper installation . . . and thoughtful operation on your part. DO NOT INST ALL, OP ...

  • Lincoln Electric IM573 - page 2

    2 2 POWER W A VE CALIBRA TION INDEX OF PROCEDURES Capacitor discharge procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Setup after Display Board replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Display sensor calibration . . . . . . . . . ...

  • Lincoln Electric IM573 - page 3

    If the sensor calibration is not done, the display board may have some problems sensing the correct overlay on power up. The display is shipped with the water cooler disabled. If an internal water cooler is being used with the Power W ave, you must use the Setup Overlay L9660 to enable the water cooler before using the system. --------------------- ...

  • Lincoln Electric IM573 - page 4

    CAP ACITOR DISCHARGE PROCEDURE Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may r esult in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid elec- trical shock, please observe all safety ...

  • Lincoln Electric IM573 - page 5

    POWER W A VE CALIBRA TION 5 5 CAP ACITOR DISCHARGE PROCEDURE (continued) CALIBRA TION TEST PROCEDURE 1. Remove main input supply power to the machine. 2. With the 3/8" nut driver , remove the scr ews that hold the handle to the machine. 3. Remove the rubber gasket (cover seal) from the lift bail. 4. With the 5/16" nut driver , remove the ...

  • Lincoln Electric IM573 - page 6

    POWER W A VE CALIBRA TION 6 6 CAP ACITOR DISCHARGE PROCEDURE (continued) FIGURE 2 – DISCHARGE LABEL D I S C H A R G E D I S C H A R G E D I S C H A R G E D I S C H A R G E D I S C H A R G E CALIBRA TION 9. Using the insulated, needle nose type jumper leads and insulated gloves, con- nect one jumper lead to one end of the resistor obtained in step ...

  • Lincoln Electric IM573 - page 7

    7 7 CAP ACITOR DISCHARGE PROCEDURE (continued) FIGURE 3 - RESISTOR WITH LEADS CONNECTED. CALIBRA TION 11. Check the voltage acr oss terminals #9 and #12 with the DC voltmeter . T erminal #9 has positive polarity and terminal #12 has negative polarity . V oltage should be zero. If any voltage remains, r epeat this capaci- tor dischar ge procedure. 1 ...

  • Lincoln Electric IM573 - page 8

    Setting up the SemiAutomatic Power W ave 450 after Display Board replacement After a Display board is installed, all users should veri- fy the polarity , sense lead and water cooler conditions. Proceed as follows: 1. Insert the SETUP Overlay (L9660) and turn the Power W ave on. 2. For the majority of applications, the wire feeder LED’s should loo ...

  • Lincoln Electric IM573 - page 9

    SENSOR CALIBRA TION TEST (FOR DISPLA Y BOARD) Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may r esult in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid elec- trical shock, please obse ...

  • Lincoln Electric IM573 - page 10

    10 10 SENSOR CALIBRA TION TEST (FOR DISPLA Y BOARD) (continued) Figure 4 - SENSOR LOCA TION BEHIND OVERLA Y CALIBRA TION PROCEDURE 1. Insert the CALIBRA TION AND TEST overlay (L9660-255). If this overlay is not available, turn the machine ON with no overlay in place and refer to Figure 4 to identify the keys. The overlay ID number is momentarily di ...

  • Lincoln Electric IM573 - page 11

    SEMIAUTOMA TIC PW450 QUICK VOL T AGE CALIBRA TION Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may r esult in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid elec- trical shock, please ...

  • Lincoln Electric IM573 - page 12

    12 12 SEMIAUTOMA TIC PW450 QUICK VOL T AGE CALIBRA TION (continued) Figure 5 - TEST AND CALIBRA TION OVERLA Y (32) (34) (36) (64) (33) (35) (37) (65) (67) (96) (97) (98) (99) (100) (101) (132) (133) (128) (130) (129) (131) CALIBRA TION PROCEDURE 1. Before changing or disturbing the defective display board, power up the machine with the L9660-255 T ...

  • Lincoln Electric IM573 - page 13

    CALIBRA TION 13 13 ROBOTIC PW450 QUICK VOL T AGE CALIBRA TION Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may r esult in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid elec- trical sh ...

  • Lincoln Electric IM573 - page 14

    CALIBRA TION 14 14 POWER W A VE CALIBRA TION ROBOTIC PW450 QUICK VOL T AGE CALIBRA TION (continued) Figure 5 - TEST AND CALIBRA TION OVERLA Y (32) (34) (36) (64) (33) (35) (37) (65) (67) (96) (97) (98) (99) (100) (101) (132) (133) (128) (130) (129) (131) PROCEDURE 1. Before changing or disturbing the defective display board, power up the machine wi ...

  • Lincoln Electric IM573 - page 15

    SEMIAUTOMA TIC PW450 FULL VOL T AGE CALIBRA TION Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may r esult in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid elec- trical shock, please o ...

  • Lincoln Electric IM573 - page 16

    PROCEDURE 1. The voltage calibration numbers ar e stored in the display board. They ar e program- mable from the fr ont panel using the T est and Calibration Overlay . 2. Change the PC board in question. 3. Install the T est and Calibration Overlay L9660-255 and power up the machine. See Figure 6. 4. Press the V oltage Calibration function (32). Th ...

  • Lincoln Electric IM573 - page 17

    CALIBRA TION 17 17 POWER W A VE CALIBRA TION ROBOTIC PW450 FULL VOL T AGE CALIBRA TION Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may r esult in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and ...

  • Lincoln Electric IM573 - page 18

    CALIBRA TION 18 18 POWER PROCEDURE 1. The voltage calibration numbers ar e stored in the display board. They ar e program- mable from the fr ont panel using the T est and Calibration Overlay . 2. Change the PC board in question. 3. Install the T est and Calibration Overlay L9660-255 and power up the machine. See Figure 6. 4. Press the V oltage Cali ...

  • Lincoln Electric IM573 - page 19

    SEMIAUTOMA TIC PW450 FULL VOL T AGE CALIBRA TION USING A WELDING ARC Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may r esult in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid elec- tr ...

  • Lincoln Electric IM573 - page 20

    20 20 SEMIAUTOMA TIC PW450 FULL VOL T AGE CALIBRA TION USING A WELDING ARC (continued) Figure 7 - TEST AND CALIBRA TION OVERLA Y (32) (34) (36) (64) (33) (35) (37) (65) (67) (96) (97) (98) (99) (100) (101) (132) (133) (128) (130) (129) (131) CALIBRA TION PROCEDURE 1. The voltage calibration numbers ar e stored in the display board. They ar e progra ...

  • Lincoln Electric IM573 - page 21

    21 21 SEMIAUTOMA TIC PW450 FULL VOL T AGE CALIBRA TION USING A WELDING ARC (continued) CALIBRA TION – POLARITY (+21A) + POLARITY – POLARITY NOTE: Do not attempt to weld for –Polarity (+21A). Set the number to the same as recor ded for +Polarity (+67A). Also for +Polarity and –Polarity , move the volt- meter sense lead from the conductor blo ...

  • Lincoln Electric IM573 - page 22

    SEMIAUTOMA TIC PW450 CURRENT CALIBRA TION Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may r esult in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid elec- trical shock, please observe ...

  • Lincoln Electric IM573 - page 23

    23 23 SEMIAUTOMA TIC PW450 CURRENT CALIBRA TION (continued) CALIBRA TION 2. Locate the 10 tur n trimmer potentiometer located on the control boar d. It is the only trimmer on the board. If the trimmer is not accessible with the control boar d installed, then the board must be r emoved and laid on the top of the PC board compartment. Be sure the con ...

  • Lincoln Electric IM573 - page 24

    24 24 SEMIAUTOMA TIC PW450 CURRENT CALIBRA TION (continued) CALIBRA TION PROCEDURE 1. Install the T est and Calibration Overlay and apply power to the machine. See Figure 10. 2. Press the Manual Pr ocedure Entry Key (64). The machine should display the following: PROCESS 1 SETUP 1-0 3. T oggle the Arrow Keys (100 and 101) until the display reads: P ...

  • Lincoln Electric IM573 - page 25

    CALIBRA TION 25 25 POWER W A VE CALIBRA TION ROBOTIC PW450 CURRENT CALIBRA TION Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may r esult in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avo ...

  • Lincoln Electric IM573 - page 26

    CALIBRA TION 26 26 POWER W A VE CALIBRA TION ROBOTIC PW450 CURRENT CALIBRA TION (continued) 2. Locate the 10 tur n trimmer potentiometer located on the control boar d. It is the only trimmer on the board. If the trimmer is not accessible with the control boar d installed, then the board must be r emoved and laid on the top of the PC board compartme ...

  • Lincoln Electric IM573 - page 27

    CALIBRA TION 27 27 POWER ROBOTIC PW450 CURRENT CALIBRA TION (continued) PROCEDURE 1. Install the T est and Calibration Overlay and apply power to the machine. See Figure 10. 2. Press the Manual Pr ocedure Entry Key (64). The machine should display the following: PROCESS 1 SETUP 1-0 3. T oggle the Arrow Keys (100 and 101) until the display reads: PR ...

  • Lincoln Electric IM573 - page 28

    The Power W ave 450 Robotic may be triggered inde- pendent of the robot using the following circuit and pro- cedure. 1. Remove the large connector plug on the rear of the PW450. (As viewed from the front of the machine). 2. Connect a normally open switch and a 24VDC sup- ply either to the large connector plug (P82) or to the harness connectors on t ...

  • Lincoln Electric IM573 - page 29

    CALIBRA TION 29 29 POWER W A VE CALIBRA TION ROBOTIC INTERF ACE P .C. BOARD CALIBRA TION Position Interface board on top of the power wave so that the component side is up. Make certain a non-con- ductive insulating material is protecting the control board from touching any conductive surface. Locate the J109 receptacle. Directly next to the recept ...

  • Lincoln Electric IM573 - page 30

    ROBOTIC INTERF ACE CONNECTIONS 30 30 POWER W A VE CALIBRA TION ARCTOOL WELDING INPUTS AND OUT- PUTS J101-1 +Serial loop CTRL J27-1 J101-2 High speed sense 1 P83-K J101-3 High speed sense 2 P83-L J101-4 -Serial loop CTRL J27-4 J104-1 V oltage signal CTRL J21-4 J104-2 Current signal CTRL J21-7 J104-3 W ater PWR D.K. J16-4 J104-4 +output signal SNUB J ...

  • Lincoln Electric IM573 - page 31

    TEST PROCEDURE AFTER REP AIR 31 31 POWER W A VE CALIBRA TION The following five steps should be completed after examining and or repairing a Power W ave 450R. These steps will insure that all aspects and systems of the Power W ave are functioning. This procedure does not include fan operation, or proper water cooler operation, both of which are ind ...

  • Lincoln Electric IM573 - page 32

    • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 441 17-1 199 U.S.A. TEL: 216.481.8100 F AX: 216.486.1751 WEB SITE: www .lincolnelectric.com • World's Leader in W elding and Cutting Products • ...

Fabricante Lincoln Electric Categoría Welder

Los documentos del dispositivo Lincoln Electric IM573 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Lincoln Electric
- manuales de instrucciones IM573
- hojas de producto Lincoln Electric
- folletos informativos
- o etiquetas energéticas Lincoln Electric IM573
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Lincoln Electric IM573.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Lincoln Electric IM573, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Lincoln Electric IM573. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Lincoln Electric IM573.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Lincoln Electric IM573, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Lincoln Electric IM573. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Lincoln Electric IM573.

El manual de instrucciones completo de Lincoln Electric debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Lincoln Electric IM573 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Lincoln Electric IM573, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Lincoln Electric IM573 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Lincoln Electric IM573 - que deben facilitarnos los primeros pasos durante el uso de Lincoln Electric IM573
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Lincoln Electric IM573
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Lincoln Electric IM573 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Lincoln Electric IM573?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Lincoln Electric IM573, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Lincoln Electric IM573 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)