Français dropdown-ico

Manuel d’utilisation Vermont Castings RUVS40

24 pages 0.77 mb
Télécharger

Aller à la page of 24

Summary
  • Vermont Castings RUVS40 - page 1

    1 Vermont Castings Radiance Tested and listed to ANSI Z21.11.2b-1998, Unvented Heaters W ARNING: Improper installa- tion, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual for correct installa- tion and operational procedures. For assistance or additional infor- mation consult a qualified insta ...

  • Vermont Castings RUVS40 - page 2

    2 Vermont Castings Radiance ATTENTION CONSUMER: In order to ensure safe and effective installation, this unit must be installed only by a qualified agency, individual, firm, corporation, or company that is experienced in the installation, repair and servicing of this type of appliance and is familiar with the building codes and installation techniq ...

  • Vermont Castings RUVS40 - page 3

    3 Vermont Castings Radiance Fuel Type: NG LP Manifold Pressure; Min. / Max.: 1.7"/3.5" 5.4"/11.0" Min. Inlet Supply Pressure for adjustment:: 5.0" W.C. 11.0" W.C. Max. Inlet Supply Pressure for adjustment: 8.0" W.C. 12.0" W.C. Min. Output, BTU/hr: 26,000 26,000 Max. Output, BTU/hr: 35,000 35,000 Ignition : Pi ...

  • Vermont Castings RUVS40 - page 4

    4 Vermont Castings Radiance 1. Install only in accordance with National Fuel Gas Code, ANSI Z223.1 - latest edition. (Exception: Do not derate this appliance for altitude. This appliance has been tested and listed for use in altitudes up to 10,000 feet. Maintain the manifold pressure at 3.5 inches W .C. for Natural Gas and 1 1 inches W .C. for LP g ...

  • Vermont Castings RUVS40 - page 5

    5 Vermont Castings Radiance General Infor mation V ent Free Features The Radiance RUVS40 is an unvented gas heating appliance tested and listed to the ANSI standard Z21.11.2a 1997. This appliance is specifically configured to burn either Natural Gas or Propane fuel, as indicated on the metal rating plate attached to the rear shroud. The Radiance RU ...

  • Vermont Castings RUVS40 - page 6

    6 Vermont Castings Radiance Installation Requirements THIS HEATER MUST HAVE FRESH AIR FOR PROPER OPERATION. IF NOT, POOR FUEL COMBUSTION COULD RESULT. READ THE FOLLOWING INSTRUCTIONS TO INSURE PROPER FRESH AIR FOR THIS AND OTHER FUEL-BURNING APPLIANCES IN YOUR HOME. WARNING Fresh Air Requirements for Combustion and V entilation Modern construction ...

  • Vermont Castings RUVS40 - page 7

    7 Vermont Castings Radiance 3. Add the BTU/Hr ratings of all fuel-burning appli- ances installed in the same space, including the following: Gas W ater Heater Gas Furnace Gas Fireplace Logs Unvented Gas Heater V ented Gas Heater* Other Gas Appliances* * Do not include Direct V ent appliances as these utilize outside air for combustion and vent to t ...

  • Vermont Castings RUVS40 - page 8

    8 Vermont Castings Radiance A: Maximum Alcove Depth .............. 24" (609mm) B: T o Side W all ................................... 4" (101mm) C: T o Rear W all ................................. 4" (101mm) D: T o Ceiling ................................... 60" (1524mm) The Radiance Unvented heater may be installed in an alcove ...

  • Vermont Castings RUVS40 - page 9

    9 Vermont Castings Radiance Assembly Read these instructions thoroughly before starting the assembly. Follow procedures in the order given. Inspect the stove for damage before starting the assembly. Do not install this stove if any damage is evident. Contact your dealer immedi- ately. The Radiance is shipped on its back, mounted to a wooden pallet. ...

  • Vermont Castings RUVS40 - page 10

    10 Vermont Castings Radiance Install Optional Fan, #2767/FK26 Install the fan kit before the stove is connected to the gas line. The fan consists of a blower assembly and a rheostat switch that are connected by a wire harness. The blower attaches to brackets at the bottom of the rear shroud. The rheostat installs within the remote switch box, at th ...

  • Vermont Castings RUVS40 - page 11

    11 Vermont Castings Radiance 5. Resecure the Rear Shroud panels. • Reinstall and tighten the two sheet metal screws (D, Fig. 10) that secure the inner and outer shrouds together . • Secure the upper corner of the shroud and switch box to the side of the stove using a 1/4 -20 x 1/2” round head phillips screw , previously removed. (B, Fig.10) F ...

  • Vermont Castings RUVS40 - page 12

    12 Vermont Castings Radiance Connect the Gas Line Gas connection should be made in accordance with the current edition of the National Fuel Gas Code, ANSI Z223.1. Since some municipalities have additional local codes, be sure to consult your local authority. CAUTION • The gas line should be connected only by a qualified gas technician. Test to co ...

  • Vermont Castings RUVS40 - page 13

    13 Vermont Castings Radiance Install the Logs Install the logs in sequence as shown below. The log set includes six sections: the rear log, left and right middle logs, left and right ember logs, and an upper log. There is also a bag of lava rocks which simulate charcoal and embers. 1. Install the rear log (#1, Fig. 20) by engaging holes on its bott ...

  • Vermont Castings RUVS40 - page 14

    14 Vermont Castings Radiance 4. Loosely sprinkle the lava rocks (#6) directly on top of the burner , between the front and middle logs. Do not place any ember or lava material behind the middle logs. (Fig. 22) 5. Engage the sockets in the underside of the top log (#7) with the pegs on the rear log and the left middle log as shown in Figure 22. Ensu ...

  • Vermont Castings RUVS40 - page 15

    15 Vermont Castings Radiance Operation Y our First Fire Read these instructions carefully and familiarize yourself with the burner controls of this heater. The Radiance uses a Honeywell control valve that allows thermostatic regulation. A separate Piezo ignitor generates a spark at the pilot orifice when the button is pushed. Figures 26 - 30 illust ...

  • Vermont Castings RUVS40 - page 16

    16 Vermont Castings Radiance 1. STOP! Read the safety information above on this panel. 2. If applicable, turn thermostat to lowest setting or set burner switch to "OFF" position. 3. Push in gas control knob slightly and turn clockwise to "OFF." NOTE: Knob cannot be turned from "PILOT" to "OFF" unless knob is ...

  • Vermont Castings RUVS40 - page 17

    17 Vermont Castings Radiance T rouble- W arning T urn OFF heater and allow to cool completely before servicing. Condition No spark at Pilot when Ignitor is operated The Iignitor Electrode sparks, but Pilot does not light Pilot lights but flame goes out when Contorl Knob is released. Possible Cause 1.Ignition Electrode is disconnected from ignition ...

  • Vermont Castings RUVS40 - page 18

    18 Vermont Castings Radiance T roubleshooting (continued) Condition Pilot lights but Main Burner does not Main Burner shuts off and Pilot flame goes out while in operation Possible Cause 1. Gas supply line shutoff valve is not fully open. 2. Foreign material is blocking Burner ports. 3. Main Burner orifice is clogged. 4. Thermostat or remote switch ...

  • Vermont Castings RUVS40 - page 19

    19 Vermont Castings Radiance Maintenance Your Radiance Vent Free heater will provide years of service with minimal upkeep. The following procedures will help ensure that your heater continues to perform safely and efficiently. Firebox Cleaning and Inspection Cleanliness is critical to correct operation of the heater. The log set, burner, valve cont ...

  • Vermont Castings RUVS40 - page 20

    20 Vermont Castings Radiance Catalytic Combustor The combustor should be cleaned annually to ensure optimal performance. Follow the procedure below. Tools / Materials: • phillips screwdriver • rubber gloves • baking soda • tap water • white vinegar • distilled water Remove the combustor module 1. Be sure that the heater is COLD. 2. Remo ...

  • Vermont Castings RUVS40 - page 21

    21 Vermont Castings Radiance Item/Model Number Part Number Radiance V ent Free Gas Heater RUVS40 Item/Model Number Part Number 2 4 3 20 18 19 60 60 54 52 52 55 56 55 56 53 51 51 53 58 6 16 23 12 13 1 14 33 15 57 52 5 51 53 36 35 34 58 52 45 38 39 62 55 53 57 53 47 50 32 25 29 28 30 31 27 26 9 46 49 48 17 16 11 22 44 51 53 51 53 37 8 8 7 7 61 57 57 ...

  • Vermont Castings RUVS40 - page 22

    22 Vermont Castings Radiance 21. Wire Clip 1208618 22. Wire Tie, Wire Harness/Rear Shroud 1201504 23. Wire Harness, Burner / Thermostat 1601913 24. Wire Harness, Snapstat Extension (not shown) 30000453 25. Gas Log Set 20000853 26. Back Log 20000856 27. Right Middle Log 20000854 28. Left Middle Log 20000855 29. Top Log 30000037 30. Left Front Ember ...

  • Vermont Castings RUVS40 - page 23

    23 Vermont Castings Radiance 7. The Vermont Castings, Majestic Products Company shall have no obligation to enhance or update any unit once manufactured. IN NO EVENT SHALL THE VERMONT CASTINGS, MAJES- TIC PRODUCTS COMPANY BE LIABLE FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES. ALL IMPLIED WARRAN- TIES, INCLUDING THE IMPLIED WARRANTIES OF MER- CHANTABIL ...

  • Vermont Castings RUVS40 - page 24

    24 Vermont Castings Radiance © The V ermont Castings, Majestic Products Company 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7885 www .majesticproducts.com • www .vermontcastings.com The V er mont Castings, Majestic Products Company ...

Fabricant Vermont Castings Catégorie Electric Heater

Les documents que nous recevons du fabricant de l'appareilVermont Castings RUVS40 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Vermont Castings
- manuels d’utilisations RUVS40
- fiches produit Vermont Castings
- dépliants
- ou étiquettes-énergie Vermont Castings RUVS40
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Vermont Castings RUVS40.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Vermont Castings RUVS40, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Vermont Castings RUVS40. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Vermont Castings RUVS40.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Vermont Castings RUVS40, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Vermont Castings RUVS40 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Vermont Castings RUVS40.

Le manuel d’utilisation complet Vermont Castings, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Vermont Castings RUVS40 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Vermont Castings RUVS40, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lVermont Castings RUVS40 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Vermont Castings RUVS40 - qui devraient nous aider dans les premières étapes lors de l'utilisation Vermont Castings RUVS40
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Vermont Castings RUVS40
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Vermont Castings RUVS40 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Vermont Castings RUVS40?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Vermont Castings RUVS40, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Vermont Castings RUVS40 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)