English dropdown-ico

Manual Vermont Castings RUVS40

24 pages 0.77 mb
Download

Go to site of 24

Summary
  • Vermont Castings RUVS40 - page 1

    1 Vermont Castings Radiance Tested and listed to ANSI Z21.11.2b-1998, Unvented Heaters W ARNING: Improper installa- tion, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual for correct installa- tion and operational procedures. For assistance or additional infor- mation consult a qualified insta ...

  • Vermont Castings RUVS40 - page 2

    2 Vermont Castings Radiance ATTENTION CONSUMER: In order to ensure safe and effective installation, this unit must be installed only by a qualified agency, individual, firm, corporation, or company that is experienced in the installation, repair and servicing of this type of appliance and is familiar with the building codes and installation techniq ...

  • Vermont Castings RUVS40 - page 3

    3 Vermont Castings Radiance Fuel Type: NG LP Manifold Pressure; Min. / Max.: 1.7"/3.5" 5.4"/11.0" Min. Inlet Supply Pressure for adjustment:: 5.0" W.C. 11.0" W.C. Max. Inlet Supply Pressure for adjustment: 8.0" W.C. 12.0" W.C. Min. Output, BTU/hr: 26,000 26,000 Max. Output, BTU/hr: 35,000 35,000 Ignition : Pi ...

  • Vermont Castings RUVS40 - page 4

    4 Vermont Castings Radiance 1. Install only in accordance with National Fuel Gas Code, ANSI Z223.1 - latest edition. (Exception: Do not derate this appliance for altitude. This appliance has been tested and listed for use in altitudes up to 10,000 feet. Maintain the manifold pressure at 3.5 inches W .C. for Natural Gas and 1 1 inches W .C. for LP g ...

  • Vermont Castings RUVS40 - page 5

    5 Vermont Castings Radiance General Infor mation V ent Free Features The Radiance RUVS40 is an unvented gas heating appliance tested and listed to the ANSI standard Z21.11.2a 1997. This appliance is specifically configured to burn either Natural Gas or Propane fuel, as indicated on the metal rating plate attached to the rear shroud. The Radiance RU ...

  • Vermont Castings RUVS40 - page 6

    6 Vermont Castings Radiance Installation Requirements THIS HEATER MUST HAVE FRESH AIR FOR PROPER OPERATION. IF NOT, POOR FUEL COMBUSTION COULD RESULT. READ THE FOLLOWING INSTRUCTIONS TO INSURE PROPER FRESH AIR FOR THIS AND OTHER FUEL-BURNING APPLIANCES IN YOUR HOME. WARNING Fresh Air Requirements for Combustion and V entilation Modern construction ...

  • Vermont Castings RUVS40 - page 7

    7 Vermont Castings Radiance 3. Add the BTU/Hr ratings of all fuel-burning appli- ances installed in the same space, including the following: Gas W ater Heater Gas Furnace Gas Fireplace Logs Unvented Gas Heater V ented Gas Heater* Other Gas Appliances* * Do not include Direct V ent appliances as these utilize outside air for combustion and vent to t ...

  • Vermont Castings RUVS40 - page 8

    8 Vermont Castings Radiance A: Maximum Alcove Depth .............. 24" (609mm) B: T o Side W all ................................... 4" (101mm) C: T o Rear W all ................................. 4" (101mm) D: T o Ceiling ................................... 60" (1524mm) The Radiance Unvented heater may be installed in an alcove ...

  • Vermont Castings RUVS40 - page 9

    9 Vermont Castings Radiance Assembly Read these instructions thoroughly before starting the assembly. Follow procedures in the order given. Inspect the stove for damage before starting the assembly. Do not install this stove if any damage is evident. Contact your dealer immedi- ately. The Radiance is shipped on its back, mounted to a wooden pallet. ...

  • Vermont Castings RUVS40 - page 10

    10 Vermont Castings Radiance Install Optional Fan, #2767/FK26 Install the fan kit before the stove is connected to the gas line. The fan consists of a blower assembly and a rheostat switch that are connected by a wire harness. The blower attaches to brackets at the bottom of the rear shroud. The rheostat installs within the remote switch box, at th ...

  • Vermont Castings RUVS40 - page 11

    11 Vermont Castings Radiance 5. Resecure the Rear Shroud panels. • Reinstall and tighten the two sheet metal screws (D, Fig. 10) that secure the inner and outer shrouds together . • Secure the upper corner of the shroud and switch box to the side of the stove using a 1/4 -20 x 1/2” round head phillips screw , previously removed. (B, Fig.10) F ...

  • Vermont Castings RUVS40 - page 12

    12 Vermont Castings Radiance Connect the Gas Line Gas connection should be made in accordance with the current edition of the National Fuel Gas Code, ANSI Z223.1. Since some municipalities have additional local codes, be sure to consult your local authority. CAUTION • The gas line should be connected only by a qualified gas technician. Test to co ...

  • Vermont Castings RUVS40 - page 13

    13 Vermont Castings Radiance Install the Logs Install the logs in sequence as shown below. The log set includes six sections: the rear log, left and right middle logs, left and right ember logs, and an upper log. There is also a bag of lava rocks which simulate charcoal and embers. 1. Install the rear log (#1, Fig. 20) by engaging holes on its bott ...

  • Vermont Castings RUVS40 - page 14

    14 Vermont Castings Radiance 4. Loosely sprinkle the lava rocks (#6) directly on top of the burner , between the front and middle logs. Do not place any ember or lava material behind the middle logs. (Fig. 22) 5. Engage the sockets in the underside of the top log (#7) with the pegs on the rear log and the left middle log as shown in Figure 22. Ensu ...

  • Vermont Castings RUVS40 - page 15

    15 Vermont Castings Radiance Operation Y our First Fire Read these instructions carefully and familiarize yourself with the burner controls of this heater. The Radiance uses a Honeywell control valve that allows thermostatic regulation. A separate Piezo ignitor generates a spark at the pilot orifice when the button is pushed. Figures 26 - 30 illust ...

  • Vermont Castings RUVS40 - page 16

    16 Vermont Castings Radiance 1. STOP! Read the safety information above on this panel. 2. If applicable, turn thermostat to lowest setting or set burner switch to "OFF" position. 3. Push in gas control knob slightly and turn clockwise to "OFF." NOTE: Knob cannot be turned from "PILOT" to "OFF" unless knob is ...

  • Vermont Castings RUVS40 - page 17

    17 Vermont Castings Radiance T rouble- W arning T urn OFF heater and allow to cool completely before servicing. Condition No spark at Pilot when Ignitor is operated The Iignitor Electrode sparks, but Pilot does not light Pilot lights but flame goes out when Contorl Knob is released. Possible Cause 1.Ignition Electrode is disconnected from ignition ...

  • Vermont Castings RUVS40 - page 18

    18 Vermont Castings Radiance T roubleshooting (continued) Condition Pilot lights but Main Burner does not Main Burner shuts off and Pilot flame goes out while in operation Possible Cause 1. Gas supply line shutoff valve is not fully open. 2. Foreign material is blocking Burner ports. 3. Main Burner orifice is clogged. 4. Thermostat or remote switch ...

  • Vermont Castings RUVS40 - page 19

    19 Vermont Castings Radiance Maintenance Your Radiance Vent Free heater will provide years of service with minimal upkeep. The following procedures will help ensure that your heater continues to perform safely and efficiently. Firebox Cleaning and Inspection Cleanliness is critical to correct operation of the heater. The log set, burner, valve cont ...

  • Vermont Castings RUVS40 - page 20

    20 Vermont Castings Radiance Catalytic Combustor The combustor should be cleaned annually to ensure optimal performance. Follow the procedure below. Tools / Materials: • phillips screwdriver • rubber gloves • baking soda • tap water • white vinegar • distilled water Remove the combustor module 1. Be sure that the heater is COLD. 2. Remo ...

  • Vermont Castings RUVS40 - page 21

    21 Vermont Castings Radiance Item/Model Number Part Number Radiance V ent Free Gas Heater RUVS40 Item/Model Number Part Number 2 4 3 20 18 19 60 60 54 52 52 55 56 55 56 53 51 51 53 58 6 16 23 12 13 1 14 33 15 57 52 5 51 53 36 35 34 58 52 45 38 39 62 55 53 57 53 47 50 32 25 29 28 30 31 27 26 9 46 49 48 17 16 11 22 44 51 53 51 53 37 8 8 7 7 61 57 57 ...

  • Vermont Castings RUVS40 - page 22

    22 Vermont Castings Radiance 21. Wire Clip 1208618 22. Wire Tie, Wire Harness/Rear Shroud 1201504 23. Wire Harness, Burner / Thermostat 1601913 24. Wire Harness, Snapstat Extension (not shown) 30000453 25. Gas Log Set 20000853 26. Back Log 20000856 27. Right Middle Log 20000854 28. Left Middle Log 20000855 29. Top Log 30000037 30. Left Front Ember ...

  • Vermont Castings RUVS40 - page 23

    23 Vermont Castings Radiance 7. The Vermont Castings, Majestic Products Company shall have no obligation to enhance or update any unit once manufactured. IN NO EVENT SHALL THE VERMONT CASTINGS, MAJES- TIC PRODUCTS COMPANY BE LIABLE FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES. ALL IMPLIED WARRAN- TIES, INCLUDING THE IMPLIED WARRANTIES OF MER- CHANTABIL ...

  • Vermont Castings RUVS40 - page 24

    24 Vermont Castings Radiance © The V ermont Castings, Majestic Products Company 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7885 www .majesticproducts.com • www .vermontcastings.com The V er mont Castings, Majestic Products Company ...

Manufacturer Vermont Castings Category Electric Heater

Documents that we receive from a manufacturer of a Vermont Castings RUVS40 can be divided into several groups. They are, among others:
- Vermont Castings technical drawings
- RUVS40 manuals
- Vermont Castings product data sheets
- information booklets
- or energy labels Vermont Castings RUVS40
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vermont Castings RUVS40.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vermont Castings RUVS40, service manual, brief instructions and user manuals Vermont Castings RUVS40. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vermont Castings RUVS40.

Similar manuals

A complete manual for the device Vermont Castings RUVS40, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vermont Castings RUVS40 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vermont Castings RUVS40.

A complete Vermont Castings manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vermont Castings RUVS40 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vermont Castings RUVS40, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vermont Castings RUVS40, that we can find in the current document
3. Tips how to use the basic functions of the device Vermont Castings RUVS40 - which should help us in our first steps of using Vermont Castings RUVS40
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vermont Castings RUVS40
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vermont Castings RUVS40 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vermont Castings RUVS40?

Use the form below

If you did not solve your problem by using a manual Vermont Castings RUVS40, ask a question using the form below. If a user had a similar problem with Vermont Castings RUVS40 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)