Français dropdown-ico

Manuel d’utilisation Pelco c2626M

24 pages 0.67 mb
Télécharger

Aller à la page of 24

Summary
  • Pelco c2626M - page 1

    ® INST ALLA TION SX8205R Unmanaged Ethernet Switch Five 10BASE-T/100BASE-TX Ports C2626M (2/07) ...

  • Pelco c2626M - page 2

    2 C2626M (2/07) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Not ices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview . . . . . . . . . . . . . . . . . ...

  • Pelco c2626M - page 3

    C2626M (2/0 7) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Inst all in accordance with the manufacturer’ s instructions. 8. Do not install n ...

  • Pelco c2626M - page 4

    4 C2626M (2/07) The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NO ...

  • Pelco c2626M - page 5

    C2626M (2/0 7) 5 Regulatory Notices This device complies with Part 15 of the FCC Rule s. Operation is subject to the following two conditions: (1) this device may not cause harmful in terference, and (2) this device must accept any interference received, including interfer ence that may cause undesired operation. RADIO AND TELEVIS ION INTERFERENCE ...

  • Pelco c2626M - page 6

    6 C2626M (2/07) Product Overview DESCRIPTION The SX8205R unmanaged Ethernet switch provides five 10B ASE-T/100BASE-TX ports for the transport of bidirectional Ethernet data. Operating as a single switch in a net work, the SX8205R module connects to up to five 10BASE-T/100BASE-TX Ether net devices. If a larger switched network is needed, multiple SX ...

  • Pelco c2626M - page 7

    C2626M (2/0 7) 7 • Compliant with IEEE 802.3, 802.3u, and 802.3x standards • 10BASE-T/100BASE-TX compat ibility with all Pelco ® and third-pa rty 10BASE-T/100BASE-TX Ethernet devices • Environmentally hardened • Designed to meet NEMA TS 2 and Caltrans traff ic signal control equipment standards for ambient operating temperature, mechanical ...

  • Pelco c2626M - page 8

    8 C2626M (2/07) FRONT PANEL Figure 2 illustrates the front panel of the SX8205R module. Figure 2. Front Panel of SX8205R Module ì Reset Button: Restarts the un it î Power LED: Pelco badge NOTE: For additional information ab out the Power LED, refer to T roubleshooting on page 15. ...

  • Pelco c2626M - page 9

    C2626M (2/0 7) 9 REAR PANEL Figure 3 illustrates the rear panel of the SX8205R module. Figure 3. Rear Panel of SX8205R Module For additional information about r ear -panel connections, refer to Installation on page 10. For detailed information about the RJ-45 LEDs, refer to T roubleshooting on page 15. ì Rack Power/Alarm Connector: 4-pin connector ...

  • Pelco c2626M - page 10

    10 C2626M (2/07) Installation PACKAGE CONTENTS The following it ems are supplied: 1 SX8205R module 1 Regulated switching power suppl y with four plug adapt ers (North American, Australian, U.K., and European configurations); 100-240 V A C, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4 - 40 x 0.250-inch Phillips pa n head screws with lock wa ...

  • Pelco c2626M - page 11

    C2626M (2/0 7) 11 Using the TX Mode switch for a parti cular port, y ou can do the following: • Enable autonegotiation or select (force) a specific data rate and duplex mode: – Enabling autonegotiation allows the SX8205R module to automatically negotiate with the device to which the port is connected fo r data rate and duplex modes of operation ...

  • Pelco c2626M - page 12

    12 C2626M (2/07) NOTE: TX Mode configuration must be set when the module is powered off. If you wish to change a TX Mode switch setting after the module has been powered on, power of f the module, change the TX Mode switch setting, and then power on the module again. MOUNTING The SX8205R module can be mounted into a rack or can be used as a stand-a ...

  • Pelco c2626M - page 13

    C2626M (2/0 7) 13 Mounting the SX8205R Module Using the W all Clip NOTE: Before mounting the SX8205R module to a wall, ensure that there is adequate space at both ends for viewing the front-panel Pow er LED and for making the various rear -panel cable connections. T o attach the SX8205R module to a wall using the supplied wall clip, refer to Figure ...

  • Pelco c2626M - page 14

    14 C2626M (2/07) CONNECTIONS Connections to the SX8205R module are made on the rear panel of the module (refer to Figure 6). Figure 6. SX8205R Module Co nnections As illustrated in Figure 6, SX8205R module connections consist of the following: • Power connection NOTES: – A 12 VDC or 24 VA C power supply can be us ed to power the module when use ...

  • Pelco c2626M - page 15

    C2626M (2/0 7) 15 T roubleshooting LED indicators on the front and rear panels of the SX8205R module allow you to monitor operational status: • The Power LED (Pelco badge) on t he front panel (refer to Figure 2) allows you to monitor operating power . Refer to T able B for info rmation about the Power LED and associated troubleshooting guidelines ...

  • Pelco c2626M - page 16

    16 C2626M (2/07) T able C. T roubleshooting with Rear -Panel Indicators Indicator Color Meaning Possible Cause Corrective Action RJ-45 10BASE-T/100BASE-TX Port Stat us LED - Left (Link / Activity) Amber A 10BASE-T link is established. — If 10BASE-T operation is desired, no action is required. If 10BASE-T operation is not desired, refer to Setting ...

  • Pelco c2626M - page 17

    C2626M (2/0 7) 17 RJ-45 10BASE-T/100BASE-TX Port Status LED - Left (Link/Activity) (Continued) Not lit A 10BASE-T or 100BASE-TX link cannot be established. A problem may exist with the cable: • Cable is not connected to the module or to the 10BASE-T/100BASE-TX compatible device. • Cable is defective. • Cable is not the proper cable type. • ...

  • Pelco c2626M - page 18

    18 C2626M (2/07) RJ-45 10BASE-T/100BASE-TX Port St atus LED - Right (Duplex/Collision) Amber Port is set to 10BASE-T full- duplex mode. — If 10BASE-T full-duplex operation is desired, no action is required. If 10BASE-T full- duplex operation is not desired, refer to Setting 10BASE-T/100BASE-TX Port Modes of Operation on page 10 for information. F ...

  • Pelco c2626M - page 19

    C2626M (2/0 7) 19 RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Green Port is set to 100BASE-TX full- duplex mode. — If 100BASE-TX full-duplex operation is desired, no action is required. If 100BASE-TX full- duplex operation is not desired, refer to Setting 10BASE-T/100BASE-TX Port Modes of Operation on page 10 ...

  • Pelco c2626M - page 20

    20 C2626M (2/07) RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Not lit Port is set to 10BASE-T half- duplex mode and no collisions are detected.* — If 10BASE-T half-duplex operation is desired, no action is required. If 10BASE-T half- duplex operation is not desired, refer to Setting 10BASE-T/100BASE-TX Port Mo ...

  • Pelco c2626M - page 21

    C2626M (2/0 7) 21 Specifications PERFORMANCE Switch T ype Unmanaged Layer 2 Switch Method Store and forward Switch Fabric Non-head-of-line blocking Data Rate 10/100 Mbps Compliance IEEE 802.3, 802.3u, 802.3x Interface Auto MDI/MDI-X Operating Mode Full- duplex or half-duplex Address T able Size 1,024 MAC address ent ries with automatic learning and ...

  • Pelco c2626M - page 22

    22 C2626M (2/07) Appendix. RJ-45 Connector Pinouts Figure 7 illustrates RJ-45 MDI/MDI-X connector pinouts. Figure 7. RJ-45 MDI/MDI-X Connector Pinouts T able D summarizes RJ-45 MDI/MDI-X connector pinouts. T able D. RJ-45 MDI/MDI-X Connector Pinouts Pin Number MDI (Normal Mode) MDI-X (Crossed Mode) 1R X + T X + 2R X - T X - 3 TX+ RX+ 4 Not used Not ...

  • Pelco c2626M - page 23

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment. Exception s to this warranty are as noted below: • Five years on fiber o ptic products and TW3 000 Series unshield ed twisted pair tr an ...

  • Pelco c2626M - page 24

    ® Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Ara ...

Fabricant Pelco Catégorie Switch

Les documents que nous recevons du fabricant de l'appareilPelco c2626M peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Pelco
- manuels d’utilisations c2626M
- fiches produit Pelco
- dépliants
- ou étiquettes-énergie Pelco c2626M
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Pelco c2626M.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Pelco c2626M, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Pelco c2626M. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Pelco c2626M.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Pelco c2626M, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Pelco c2626M par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Pelco c2626M.

Le manuel d’utilisation complet Pelco, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Pelco c2626M - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Pelco c2626M, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPelco c2626M qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Pelco c2626M - qui devraient nous aider dans les premières étapes lors de l'utilisation Pelco c2626M
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Pelco c2626M
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Pelco c2626M dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Pelco c2626M?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Pelco c2626M, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Pelco c2626M il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)