English dropdown-ico

Manual Pelco c2626M

24 pages 0.67 mb
Download

Go to site of 24

Summary
  • Pelco c2626M - page 1

    ® INST ALLA TION SX8205R Unmanaged Ethernet Switch Five 10BASE-T/100BASE-TX Ports C2626M (2/07) ...

  • Pelco c2626M - page 2

    2 C2626M (2/07) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Not ices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview . . . . . . . . . . . . . . . . . ...

  • Pelco c2626M - page 3

    C2626M (2/0 7) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Inst all in accordance with the manufacturer’ s instructions. 8. Do not install n ...

  • Pelco c2626M - page 4

    4 C2626M (2/07) The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NO ...

  • Pelco c2626M - page 5

    C2626M (2/0 7) 5 Regulatory Notices This device complies with Part 15 of the FCC Rule s. Operation is subject to the following two conditions: (1) this device may not cause harmful in terference, and (2) this device must accept any interference received, including interfer ence that may cause undesired operation. RADIO AND TELEVIS ION INTERFERENCE ...

  • Pelco c2626M - page 6

    6 C2626M (2/07) Product Overview DESCRIPTION The SX8205R unmanaged Ethernet switch provides five 10B ASE-T/100BASE-TX ports for the transport of bidirectional Ethernet data. Operating as a single switch in a net work, the SX8205R module connects to up to five 10BASE-T/100BASE-TX Ether net devices. If a larger switched network is needed, multiple SX ...

  • Pelco c2626M - page 7

    C2626M (2/0 7) 7 • Compliant with IEEE 802.3, 802.3u, and 802.3x standards • 10BASE-T/100BASE-TX compat ibility with all Pelco ® and third-pa rty 10BASE-T/100BASE-TX Ethernet devices • Environmentally hardened • Designed to meet NEMA TS 2 and Caltrans traff ic signal control equipment standards for ambient operating temperature, mechanical ...

  • Pelco c2626M - page 8

    8 C2626M (2/07) FRONT PANEL Figure 2 illustrates the front panel of the SX8205R module. Figure 2. Front Panel of SX8205R Module ì Reset Button: Restarts the un it î Power LED: Pelco badge NOTE: For additional information ab out the Power LED, refer to T roubleshooting on page 15. ...

  • Pelco c2626M - page 9

    C2626M (2/0 7) 9 REAR PANEL Figure 3 illustrates the rear panel of the SX8205R module. Figure 3. Rear Panel of SX8205R Module For additional information about r ear -panel connections, refer to Installation on page 10. For detailed information about the RJ-45 LEDs, refer to T roubleshooting on page 15. ì Rack Power/Alarm Connector: 4-pin connector ...

  • Pelco c2626M - page 10

    10 C2626M (2/07) Installation PACKAGE CONTENTS The following it ems are supplied: 1 SX8205R module 1 Regulated switching power suppl y with four plug adapt ers (North American, Australian, U.K., and European configurations); 100-240 V A C, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4 - 40 x 0.250-inch Phillips pa n head screws with lock wa ...

  • Pelco c2626M - page 11

    C2626M (2/0 7) 11 Using the TX Mode switch for a parti cular port, y ou can do the following: • Enable autonegotiation or select (force) a specific data rate and duplex mode: – Enabling autonegotiation allows the SX8205R module to automatically negotiate with the device to which the port is connected fo r data rate and duplex modes of operation ...

  • Pelco c2626M - page 12

    12 C2626M (2/07) NOTE: TX Mode configuration must be set when the module is powered off. If you wish to change a TX Mode switch setting after the module has been powered on, power of f the module, change the TX Mode switch setting, and then power on the module again. MOUNTING The SX8205R module can be mounted into a rack or can be used as a stand-a ...

  • Pelco c2626M - page 13

    C2626M (2/0 7) 13 Mounting the SX8205R Module Using the W all Clip NOTE: Before mounting the SX8205R module to a wall, ensure that there is adequate space at both ends for viewing the front-panel Pow er LED and for making the various rear -panel cable connections. T o attach the SX8205R module to a wall using the supplied wall clip, refer to Figure ...

  • Pelco c2626M - page 14

    14 C2626M (2/07) CONNECTIONS Connections to the SX8205R module are made on the rear panel of the module (refer to Figure 6). Figure 6. SX8205R Module Co nnections As illustrated in Figure 6, SX8205R module connections consist of the following: • Power connection NOTES: – A 12 VDC or 24 VA C power supply can be us ed to power the module when use ...

  • Pelco c2626M - page 15

    C2626M (2/0 7) 15 T roubleshooting LED indicators on the front and rear panels of the SX8205R module allow you to monitor operational status: • The Power LED (Pelco badge) on t he front panel (refer to Figure 2) allows you to monitor operating power . Refer to T able B for info rmation about the Power LED and associated troubleshooting guidelines ...

  • Pelco c2626M - page 16

    16 C2626M (2/07) T able C. T roubleshooting with Rear -Panel Indicators Indicator Color Meaning Possible Cause Corrective Action RJ-45 10BASE-T/100BASE-TX Port Stat us LED - Left (Link / Activity) Amber A 10BASE-T link is established. — If 10BASE-T operation is desired, no action is required. If 10BASE-T operation is not desired, refer to Setting ...

  • Pelco c2626M - page 17

    C2626M (2/0 7) 17 RJ-45 10BASE-T/100BASE-TX Port Status LED - Left (Link/Activity) (Continued) Not lit A 10BASE-T or 100BASE-TX link cannot be established. A problem may exist with the cable: • Cable is not connected to the module or to the 10BASE-T/100BASE-TX compatible device. • Cable is defective. • Cable is not the proper cable type. • ...

  • Pelco c2626M - page 18

    18 C2626M (2/07) RJ-45 10BASE-T/100BASE-TX Port St atus LED - Right (Duplex/Collision) Amber Port is set to 10BASE-T full- duplex mode. — If 10BASE-T full-duplex operation is desired, no action is required. If 10BASE-T full- duplex operation is not desired, refer to Setting 10BASE-T/100BASE-TX Port Modes of Operation on page 10 for information. F ...

  • Pelco c2626M - page 19

    C2626M (2/0 7) 19 RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Green Port is set to 100BASE-TX full- duplex mode. — If 100BASE-TX full-duplex operation is desired, no action is required. If 100BASE-TX full- duplex operation is not desired, refer to Setting 10BASE-T/100BASE-TX Port Modes of Operation on page 10 ...

  • Pelco c2626M - page 20

    20 C2626M (2/07) RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Not lit Port is set to 10BASE-T half- duplex mode and no collisions are detected.* — If 10BASE-T half-duplex operation is desired, no action is required. If 10BASE-T half- duplex operation is not desired, refer to Setting 10BASE-T/100BASE-TX Port Mo ...

  • Pelco c2626M - page 21

    C2626M (2/0 7) 21 Specifications PERFORMANCE Switch T ype Unmanaged Layer 2 Switch Method Store and forward Switch Fabric Non-head-of-line blocking Data Rate 10/100 Mbps Compliance IEEE 802.3, 802.3u, 802.3x Interface Auto MDI/MDI-X Operating Mode Full- duplex or half-duplex Address T able Size 1,024 MAC address ent ries with automatic learning and ...

  • Pelco c2626M - page 22

    22 C2626M (2/07) Appendix. RJ-45 Connector Pinouts Figure 7 illustrates RJ-45 MDI/MDI-X connector pinouts. Figure 7. RJ-45 MDI/MDI-X Connector Pinouts T able D summarizes RJ-45 MDI/MDI-X connector pinouts. T able D. RJ-45 MDI/MDI-X Connector Pinouts Pin Number MDI (Normal Mode) MDI-X (Crossed Mode) 1R X + T X + 2R X - T X - 3 TX+ RX+ 4 Not used Not ...

  • Pelco c2626M - page 23

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment. Exception s to this warranty are as noted below: • Five years on fiber o ptic products and TW3 000 Series unshield ed twisted pair tr an ...

  • Pelco c2626M - page 24

    ® Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Ara ...

Manufacturer Pelco Category Switch

Documents that we receive from a manufacturer of a Pelco c2626M can be divided into several groups. They are, among others:
- Pelco technical drawings
- c2626M manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco c2626M
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco c2626M.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco c2626M, service manual, brief instructions and user manuals Pelco c2626M. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco c2626M.

Similar manuals

A complete manual for the device Pelco c2626M, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco c2626M by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco c2626M.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco c2626M - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco c2626M, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco c2626M, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco c2626M - which should help us in our first steps of using Pelco c2626M
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco c2626M
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco c2626M in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco c2626M?

Use the form below

If you did not solve your problem by using a manual Pelco c2626M, ask a question using the form below. If a user had a similar problem with Pelco c2626M it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)