Français dropdown-ico

Manuel d’utilisation Harbor Freight Tools 66630

22 pages 1.33 mb
Télécharger

Aller à la page of 22

Summary
  • Harbor Freight Tools 66630 - page 1

    10” HEA VY -DUTY 15 AMP T ABLE SA W 66630 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS MANUAL. Copyri ...

  • Harbor Freight Tools 66630 - page 2

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 2 SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures. Write the product’ s serial number in the back of the manual near the assembly diagram (or month and year of purchase if produc ...

  • Harbor Freight Tools 66630 - page 3

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 3 DON’T FORCE TOOL. It will do the 7. job better and safer at the rate for which it was designed. USE RIGHT TOOL. Don’t force tool 8. or attachment to do a job for which it was not designed. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOL T) NAMEPLA TE AMPERES (at f ...

  • Harbor Freight Tools 66630 - page 4

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 4 or other part that is damaged should be properly repaired or replaced. DIRECTION OF FEED. Feed work 20. into a blade or cutter against the direction of rotation of the blade or cutter only . NEVER LEA VE TOOL RUNNING 21. UNA TTENDED. TURN POWER OFF . Don’t leave tool until it c ...

  • Harbor Freight Tools 66630 - page 5

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 5 controlled workpiece to lift up and out of the saw toward the operator . Kickback is usually a result of tool misuse and can be limited or avoided by following the precautions below: Fence must be completely parallel • to the saw blade. Workpiece must be free from aws • (s ...

  • Harbor Freight Tools 66630 - page 6

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 6 Essential Straight Push-stick Features and Functions Note: Straight style (traditional) stick shown. A dif- ferent stick design may be used if it properly protects against all hazards. Diagram not to scale. Push sticks must be made from sturdy , defect-free, • plywood or normal ...

  • Harbor Freight Tools 66630 - page 7

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 7 When servicing use only identical 14. replacement parts. Only use safety equipment that has 15. been approved by an appropriate standards agency . Unapproved safety equipment may not provide adequate protection. Eye protection must be ANSI-approved and breath- ing protection must ...

  • Harbor Freight Tools 66630 - page 8

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 8 reduce the risk of vibration-related injury: Anyone using vibrating tools regu- 1. larly or for an extended period should rst be examined by a doctor and then have regular medical check- ups to ensure medical problems are not being caused or worsened from use. Pregnant women o ...

  • Harbor Freight Tools 66630 - page 9

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 9 stood, or if in doubt as to whether the tool is properly grounded. Use only 3-wire extension cords that 5. have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug. Repair or replace damaged or worn 6. cord immediately . 7. This tool is intended for use o ...

  • Harbor Freight Tools 66630 - page 10

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 10 SPECIFICA TIONS Electrical Requirements 120 V~ / 60 Hz / 15 A Motor No Load Speed 4800 RPM Blade Diameter 10” Arbor Diameter 5/8” T able Surface 16”x 26” Cutting Depth at 0° 3” Cutting Depth at 45° 2-3/8” Overload Protection Breaker Switch E105017 UNP ACKING When u ...

  • Harbor Freight Tools 66630 - page 11

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 1 1 (109) and that the tabs are on the INSIDE slot of the Splitter . Use a framing square (not included) 8. to make sure the Saw Blade and Splitter assembly are square. If not square, loosen the Splitter Bracket and adjust until the Splitter is properly aligned with the Saw Blade. ...

  • Harbor Freight Tools 66630 - page 12

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 12 Blade Depth and Angle Adjustment The Blade (96) depth should be set 1. so that outer points of the Blade are 1/8” to 1/4” higher than the workpiece while the lowest points are below the workpiece. T o raise the Blade, turn the Hand- 2. wheel (29) counterclockwise. T o lower ...

  • Harbor Freight Tools 66630 - page 13

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 13 Aligning and Adjusting the Rip Fence (146) 1. W ARNING! A misaligned Fence can cause kickbacks and jams. T o reduce risk of injury , always maintain proper Fence alignment. The Rip Fence must be parallel with the Blade and T able grooves. 2. Lift up the Fence Handle (26) and mov ...

  • Harbor Freight Tools 66630 - page 14

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 14 edge of the square until it touches the marked tooth. Rotate the Blade and check the same 7. marked tooth at the rear of the T able Saw . If the front and rear measurements 8. are not identical, have a qualied ser - vice technician repair the T able Saw . Installing/Replacing ...

  • Harbor Freight Tools 66630 - page 15

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 15 W ork Piece and Work Area Set Up Designate a work area that is clean 1. and well-lit. The work area must not allow access by children or pets to prevent injury and distraction. Route the power cord along a safe 2. route to reach the work area without creating a tripping hazard o ...

  • Harbor Freight Tools 66630 - page 16

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 16 When making a cut, use steady and 7. even pressure. Do not force cuts. Do not cut wet or warped lumber . 8. Hold the workpiece rmly with both 9. hands or use the included Push Stick. (53). Make sure the Push Stick is narrower than the workpiece and has 90° notch on one end a ...

  • Harbor Freight Tools 66630 - page 17

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 17 T o reduce possible injury should kickback occur , stand to side of the workpiece as it contacts the Blade. W ARNING! Do not stand in the line of cut. Once cut is made, turn off T able Saw . 6. W ait for Blade to come to complete stop before removing any part of workpiece. Makin ...

  • Harbor Freight Tools 66630 - page 18

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 18 MAINTENANCE AND SER VICING  Proceduresnotspecically explained in this manual must be performed only by a qualiedtechnician. TO PREVENT SERIOUS INJUR Y FROM ACCIDENT AL OPERA TION: T urn the Power Switch of the tool to its “OFF” position and unplug the to ...

  • Harbor Freight Tools 66630 - page 19

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 19 P ARTS LIST Part Description Qty . 1 Rubber feet 4 2 Bolt M6×25 5 3 Spring washer 8 4 Mat washer 13 5 Base 1 7 Bolt ST4.2×14 5 8 Sheathing 2 9 Cable press plate 1 10 Bolt M4×16 9 11 Strengthen plank 1 12 Bolt M4×8 11 13 Ruler 1 14 Nut M4 4 15 W asher 3 16 Switch Key 1 17 Swi ...

  • Harbor Freight Tools 66630 - page 20

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 20 P ARTS LIST Part Description Qty . 109 T able 1 1 10 Bolt M6×25 1 111 Bolt M6×35 1 1 12 T able insert 1 1 13 Blade Guard 1 1 14 Bolt M6×12 2 1 15 Nut M6 2 1 16 Pivot Bolt M6×50 1 1 17 Pivot Plate 1 1 18 Bolt M6X16 1 1 19 Splitter Bracket 1 120 Bolt M6×12 4 121 Wing Nut M6 1 ...

  • Harbor Freight Tools 66630 - page 21

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 21 ASSEMBL Y DIAGRAM ...

  • Harbor Freight Tools 66630 - page 22

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 22 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor , the belts ...

Fabricant Harbor Freight Tools Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilHarbor Freight Tools 66630 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Harbor Freight Tools
- manuels d’utilisations 66630
- fiches produit Harbor Freight Tools
- dépliants
- ou étiquettes-énergie Harbor Freight Tools 66630
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Harbor Freight Tools 66630.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Harbor Freight Tools 66630, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Harbor Freight Tools 66630. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Harbor Freight Tools 66630.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Harbor Freight Tools 66630, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Harbor Freight Tools 66630 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Harbor Freight Tools 66630.

Le manuel d’utilisation complet Harbor Freight Tools, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Harbor Freight Tools 66630 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Harbor Freight Tools 66630, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHarbor Freight Tools 66630 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Harbor Freight Tools 66630 - qui devraient nous aider dans les premières étapes lors de l'utilisation Harbor Freight Tools 66630
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Harbor Freight Tools 66630
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Harbor Freight Tools 66630 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Harbor Freight Tools 66630?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Harbor Freight Tools 66630, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Harbor Freight Tools 66630 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)