Italiano dropdown-ico

Manuale per l’uso Harbor Freight Tools 66630

22 pagine 1.33 mb
Scarica

Vai alla pagina of 22

Summary
  • Harbor Freight Tools 66630 - page 1

    10” HEA VY -DUTY 15 AMP T ABLE SA W 66630 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury . SA VE THIS MANUAL. Copyri ...

  • Harbor Freight Tools 66630 - page 2

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 2 SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures. Write the product’ s serial number in the back of the manual near the assembly diagram (or month and year of purchase if produc ...

  • Harbor Freight Tools 66630 - page 3

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 3 DON’T FORCE TOOL. It will do the 7. job better and safer at the rate for which it was designed. USE RIGHT TOOL. Don’t force tool 8. or attachment to do a job for which it was not designed. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOL T) NAMEPLA TE AMPERES (at f ...

  • Harbor Freight Tools 66630 - page 4

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 4 or other part that is damaged should be properly repaired or replaced. DIRECTION OF FEED. Feed work 20. into a blade or cutter against the direction of rotation of the blade or cutter only . NEVER LEA VE TOOL RUNNING 21. UNA TTENDED. TURN POWER OFF . Don’t leave tool until it c ...

  • Harbor Freight Tools 66630 - page 5

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 5 controlled workpiece to lift up and out of the saw toward the operator . Kickback is usually a result of tool misuse and can be limited or avoided by following the precautions below: Fence must be completely parallel • to the saw blade. Workpiece must be free from aws • (s ...

  • Harbor Freight Tools 66630 - page 6

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 6 Essential Straight Push-stick Features and Functions Note: Straight style (traditional) stick shown. A dif- ferent stick design may be used if it properly protects against all hazards. Diagram not to scale. Push sticks must be made from sturdy , defect-free, • plywood or normal ...

  • Harbor Freight Tools 66630 - page 7

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 7 When servicing use only identical 14. replacement parts. Only use safety equipment that has 15. been approved by an appropriate standards agency . Unapproved safety equipment may not provide adequate protection. Eye protection must be ANSI-approved and breath- ing protection must ...

  • Harbor Freight Tools 66630 - page 8

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 8 reduce the risk of vibration-related injury: Anyone using vibrating tools regu- 1. larly or for an extended period should rst be examined by a doctor and then have regular medical check- ups to ensure medical problems are not being caused or worsened from use. Pregnant women o ...

  • Harbor Freight Tools 66630 - page 9

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 9 stood, or if in doubt as to whether the tool is properly grounded. Use only 3-wire extension cords that 5. have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug. Repair or replace damaged or worn 6. cord immediately . 7. This tool is intended for use o ...

  • Harbor Freight Tools 66630 - page 10

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 10 SPECIFICA TIONS Electrical Requirements 120 V~ / 60 Hz / 15 A Motor No Load Speed 4800 RPM Blade Diameter 10” Arbor Diameter 5/8” T able Surface 16”x 26” Cutting Depth at 0° 3” Cutting Depth at 45° 2-3/8” Overload Protection Breaker Switch E105017 UNP ACKING When u ...

  • Harbor Freight Tools 66630 - page 11

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 1 1 (109) and that the tabs are on the INSIDE slot of the Splitter . Use a framing square (not included) 8. to make sure the Saw Blade and Splitter assembly are square. If not square, loosen the Splitter Bracket and adjust until the Splitter is properly aligned with the Saw Blade. ...

  • Harbor Freight Tools 66630 - page 12

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 12 Blade Depth and Angle Adjustment The Blade (96) depth should be set 1. so that outer points of the Blade are 1/8” to 1/4” higher than the workpiece while the lowest points are below the workpiece. T o raise the Blade, turn the Hand- 2. wheel (29) counterclockwise. T o lower ...

  • Harbor Freight Tools 66630 - page 13

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 13 Aligning and Adjusting the Rip Fence (146) 1. W ARNING! A misaligned Fence can cause kickbacks and jams. T o reduce risk of injury , always maintain proper Fence alignment. The Rip Fence must be parallel with the Blade and T able grooves. 2. Lift up the Fence Handle (26) and mov ...

  • Harbor Freight Tools 66630 - page 14

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 14 edge of the square until it touches the marked tooth. Rotate the Blade and check the same 7. marked tooth at the rear of the T able Saw . If the front and rear measurements 8. are not identical, have a qualied ser - vice technician repair the T able Saw . Installing/Replacing ...

  • Harbor Freight Tools 66630 - page 15

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 15 W ork Piece and Work Area Set Up Designate a work area that is clean 1. and well-lit. The work area must not allow access by children or pets to prevent injury and distraction. Route the power cord along a safe 2. route to reach the work area without creating a tripping hazard o ...

  • Harbor Freight Tools 66630 - page 16

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 16 When making a cut, use steady and 7. even pressure. Do not force cuts. Do not cut wet or warped lumber . 8. Hold the workpiece rmly with both 9. hands or use the included Push Stick. (53). Make sure the Push Stick is narrower than the workpiece and has 90° notch on one end a ...

  • Harbor Freight Tools 66630 - page 17

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 17 T o reduce possible injury should kickback occur , stand to side of the workpiece as it contacts the Blade. W ARNING! Do not stand in the line of cut. Once cut is made, turn off T able Saw . 6. W ait for Blade to come to complete stop before removing any part of workpiece. Makin ...

  • Harbor Freight Tools 66630 - page 18

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 18 MAINTENANCE AND SER VICING  Proceduresnotspecically explained in this manual must be performed only by a qualiedtechnician. TO PREVENT SERIOUS INJUR Y FROM ACCIDENT AL OPERA TION: T urn the Power Switch of the tool to its “OFF” position and unplug the to ...

  • Harbor Freight Tools 66630 - page 19

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 19 P ARTS LIST Part Description Qty . 1 Rubber feet 4 2 Bolt M6×25 5 3 Spring washer 8 4 Mat washer 13 5 Base 1 7 Bolt ST4.2×14 5 8 Sheathing 2 9 Cable press plate 1 10 Bolt M4×16 9 11 Strengthen plank 1 12 Bolt M4×8 11 13 Ruler 1 14 Nut M4 4 15 W asher 3 16 Switch Key 1 17 Swi ...

  • Harbor Freight Tools 66630 - page 20

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 20 P ARTS LIST Part Description Qty . 109 T able 1 1 10 Bolt M6×25 1 111 Bolt M6×35 1 1 12 T able insert 1 1 13 Blade Guard 1 1 14 Bolt M6×12 2 1 15 Nut M6 2 1 16 Pivot Bolt M6×50 1 1 17 Pivot Plate 1 1 18 Bolt M6X16 1 1 19 Splitter Bracket 1 120 Bolt M6×12 4 121 Wing Nut M6 1 ...

  • Harbor Freight Tools 66630 - page 21

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 21 ASSEMBL Y DIAGRAM ...

  • Harbor Freight Tools 66630 - page 22

    SKU 66630 For technical questions, please call 1-800-444-3353. Page 22 LIMITED 1 YEAR / 90 DA Y W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor , the belts ...

Fabbricante Harbor Freight Tools Categoria Saw

I documenti che otteniamo dal fabbricante del dispositivoHarbor Freight Tools 66630 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Harbor Freight Tools
- manuali per l’uso 66630
- schede prodotto Harbor Freight Tools
- opuscoli
- o etichette energetiche Harbor Freight Tools 66630
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Harbor Freight Tools 66630.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Harbor Freight Tools 66630, manuali di manutenzione, brevi manuali o manuali utente Harbor Freight Tools 66630. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Harbor Freight Tools 66630.

Manuali per l’uso simili

Manuale completo del dispositivo Harbor Freight Tools 66630, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Harbor Freight Tools 66630 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Harbor Freight Tools 66630.

Il manuale per l’uso completo Harbor Freight Tools, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Harbor Freight Tools 66630 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Harbor Freight Tools 66630, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Harbor Freight Tools 66630 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Harbor Freight Tools 66630 - che ci dovrebbe aiutare nei primi passi durante l'uso Harbor Freight Tools 66630
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Harbor Freight Tools 66630
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Harbor Freight Tools 66630 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Harbor Freight Tools 66630?

Utilizza il modulo sottostante

Se non hai risolto il problema con Harbor Freight Tools 66630 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Harbor Freight Tools 66630 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)