-
Simplicity 1692149 - page 1
Print V endor Instructions Ho w to use this file Operator’ s Manuals P aper Size: • 11x17 • Body - 50 lbs brilliant white offset or equivalent • Cov er - on pre-printed two tone “Sw ash” stock. Press: • Body - 1 color , 2-sided • Cov er - 1 color , 1 sided Bindery: • Saddle stitch, face trim *if too thic k f or saddle stitch, tape ...
-
Simplicity 1692149 - page 2
THIS P A GE INTENTIONALL Y BLANK (FOR PLA CEMENT ONL Y - DO NO T PRINT) ...
-
Simplicity 1692149 - page 3
OPERA T OR’S MANU AL Clean Sweep T win Catcher s Mfg. No. Description 1692149 Clean Sweep Twin Catcher (for 30” Mower Decks) 1692150 Clean Sweep Twin Catcher (for 34” Mower Decks) 1709142-08 Rev 04/2004 TP 100-2181-08-AT-UV Clean Sweep T win Catcher ...
-
Simplicity 1692149 - page 4
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2004 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA. ...
-
Simplicity 1692149 - page 5
1 T able of Contents Normal Installation & Remov al Installation & Remov al .....................................5 T roubleshooting Char t ................................................................7 Initial Setup & Assembl y 30” Models - Blade and Adapter Assembly .....8 34” Models - Baffle, Blade , & Adapter Assy . ..10 F ...
-
Simplicity 1692149 - page 6
2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed. SAFETY DECALS This u ...
-
Simplicity 1692149 - page 7
3 BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag ...
-
Simplicity 1692149 - page 8
4 Operation & Storage BEFORE OPERA TION Clear the lawn of all sticks, stones, wire and other debris, which may be caught or thrown by the mower blades. Clean the tube with mild detergent (other products may damage tube). Inspection windows can be removed to be cleaned. Make sure windows are securely in place before operating. Check grass condit ...
-
Simplicity 1692149 - page 9
5 Normal Installation & Removal INST ALLA TION & REMO V AL NOTE: For first-time installation, refer to Initial Setup & Installation. NOTE: If mower deck is equipped with Mulching Kit, the mulching baffles must be removed for grass collection. Make sure the high-lift blades (34') or high-lift tabs (30') are installed per the As ...
-
Simplicity 1692149 - page 10
6 Normal Installation & Removal 3. Open grass bag cover and install grass bag frames (A, figure 3) to support brackets (B). 4. On 30" mower, lift the deflector (C) up and install the adapter (A, figure 4) to mower deck by hooking bracket over the rear carriage bolt and securing with jam nut (D) and positioning front slot on the adapter und ...
-
Simplicity 1692149 - page 11
7 T roubleshooting The following table provides troubleshooting instructions for the more common and easily corrected problems. For problems not covered in the table, see your dealer. W ARNING To avoid serious Injury, perform maintenance on the grass catcher only after stopping the engine and waiting for all moving parts to come to a complete stop. ...
-
Simplicity 1692149 - page 12
8 Initial Setup & Assembly 30” MODELS - BLADE AND AD APTER ASSEMBL Y Blade Assembl y - 30” Mower 1. Remove the mower deck to access the blade or using an overhead hoist, elevate the front of the unit to access the mower blade. 2. Mount the lifts (B, Figure 6) to the discharge side of the blade as shown. Torque nuts to 14 ft. lbs. Adapter &a ...
-
Simplicity 1692149 - page 13
9 Initial Setup - 30” Models 3. Install 5/16-18 x 2-1/4 carriage bolt (A, figure 8) through front hole in mower deck along with cup (B), whiz flange nut (C), wing nut (D) and center lock nut (E). Nut (C) must be seated inside cup and center lock nut (E) should be flush with end of carriage bolt. Figure 8. A. Carriage Bolt, 5/16-18 x 2-1/4 B. Cup ...
-
Simplicity 1692149 - page 14
10 Initial Setup - 34” Models 34" MODELS - B AFFLE, BLADE, & AD APTER ASSEMBL Y Install Baffle 1. Remove mower deck from rider. Position mower deck upright and support in this position. 2. Position baffle with notched end towards discharge side opening, Install all hardware as shown in figure 10. The notch must be positioned to clear the ...
-
Simplicity 1692149 - page 15
11 Initial Setup - 34” Models Install Blades - Early Models with Splined Arbor 1. Remove existing discharge-side blade but retain hardware. Remove the retaining band (E, figure 11 b) from the arbor shaft and remove the existing splined adapter (3-3/8" O.D. F, figure 11b). This adapter can be discarded. The new 2" O.D. splined adapter su ...
-
Simplicity 1692149 - page 16
12 Initial Setup - All Models FRAME & B A GGER SUPPORT ASSEMBL Y - ALL MODELS Note: Units with 0510 transmissions use anchors (A, fig- ure 13) with a notch, all other units use anchor with no notch. See Inset Figure 13. 1. Assemble the two anchors (A, figure 13) to the trans- mission housing using the 5/16-18 x 3 capscrews (B), washers (C) and ...
-
Simplicity 1692149 - page 17
13 Initial Setup - All Models GRASS CA TCHER ASSEMBL Y - ALL MODELS NOTE: Cover and bag support are packaged as an assembly with long clevis pins and clips. It may be easier to separate components for the following step. 1. Install horizontal bag support (A, figure 14) to upright catcher support (B) holes as shown. Note that the open set of holes ( ...
-
Simplicity 1692149 - page 18
14 Initial Setup - All Models 5. Open cover and fasten cable (A, figure 17) to tube support (B) to prevent cover from going over center when opened. Loop end of cable fits over washer (C). Figure 17. A. Cable B. Support C. Washer Figure 18. A. Grass Bag Frame B. Support Frame 6. Open grass bag cover and install grass bag frames (A, figure 18) to su ...
-
Simplicity 1692149 - page 19
15 Initial Setup - All Models 7. Apply dry talc powder to rubber seal at cover open- ing. Install tube (A, figure 19) as far as possible into opening to clear adapter and install over adapter. Figure 19. A. Tube B. Wire Form Location Figure 20. A. Wire Form B. Round Cup 8. Secure tube by moving wire form (A, figure 20) down over round cup (B) on ad ...
-
Simplicity 1692149 - page 20
Installation Instructions Baffle Kit Part No. 1686783 INST ALLA TION 1. Remove the hardware (D) securing the plastic elbow (C) to the metal support plate (B). 2. Insert the baffle (A) in between the support plate (B) and elbow (C). 3. Reinstall the hardware (D). For Coronet / 400 / 2400 Series Riders Figure 1. Installation Kit Contents: Part No. Qt ...
-
Simplicity 1692149 - page 21
INSTALLATION INSTRUCTIONS EXHAUST SHIELD KIT MFG. NO. 1666610 1. Raise the seat deck to expose the right-hand top duct. 2. See figure 1. Cut out the template below and place it on the duct with the edges aligned. Tape the template in place and drill out the holes as indicat- ed using a 13/W drill bit. Figure 1. Placing Template for drilling holes 3 ...
-
Simplicity 1692149 - page 22
18 T orque Specification Chart FOR ST ANDARD MACHINE HARDWARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7.7 1/4-20 66 7.6 8 10.9 12 16.3 1/4-28 76 8 ...
Hai una domanda su Simplicity 1692149?
Utilizza il modulo sottostante
Se non hai risolto il problema con Simplicity 1692149 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Simplicity 1692149 è probabile che voglia condividere il modo di risolverlo.