Manuale per l’uso Hobart 6614 ML-134050

12 pagine 0.91 mb
Scarica

Vai alla pagina of 12

Summary
  • Hobart 6614 ML-134050 - page 1

    N S T R U C T I O N S I FORM 34527 Rev. A (Sept. 2001) MODEL 6614 MEA T SA W MODEL 6614 ML-134096 Previous models covered by this manual: 6614 ML-134050 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com ...

  • Hobart 6614 ML-134050 - page 2

    –2– Installation, Operation, and Care of MODEL 6614 MEA T SA W SA VE THESE INSTRUCTIONS GENERAL The 6614 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant 3 HP electric motor and direct gear drive transmission that provides a blade speed of 3500 feet per minute. The carriage (Fig.1) has stainless steel b ...

  • Hobart 6614 ML-134050 - page 3

    –3– INST ALLA TION UNPACKING AND ASSEMBLY Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to make sure it agrees with the specifications on the m ...

  • Hobart 6614 ML-134050 - page 4

    – 4 – UPPER PULLEY COVER (Stainless Steel) The stainless steel upper pulley cover (Fig. 5) should be installed on the two hinge pins of the stainless steel upper pulley baffle and securely latched during saw use. To remove the stainless steel upper pulley cover for cleaning, unlatch and open the stainless steel upper pulley cover; then, lift st ...

  • Hobart 6614 ML-134050 - page 5

    – 5 – LOWER PULLEY The lower pulley is assembled on the lower pulley shaft. The latch on the lower pulley should be seated in the groove of the pulley shaft (Fig. 7). The lower pulley can be removed after the blade has first been loosened and removed and the lower pulley latch is moved out of the groove of the lower pulley shaft. UPPER PULLEY T ...

  • Hobart 6614 ML-134050 - page 6

    – 6 – SCRAP TRAY During use, the scrap tray should be installed between the left-hand table and the carriage support (Fig. 9). The scrap tray slides into place, resting on the frame between the carriage support and table. The angled side of the scrap tray is located nearest the blade. Fig. 9 CARRIAGE In use, the carriage can roll back and forth ...

  • Hobart 6614 ML-134050 - page 7

    – 7 – PL-40838-1 LOWER GUIDE HOLDER LOWER BLADE GUIDE ASSEMBL Y LOWER BLADE GUIDE The lower blade guide assembly fits in the lower guide holder (Fig. 12). The blade fits in the slots of both the steel saw blade guide and the plastic guide. When the right table is removed and the plastic guide is hinged up, the lower blade guide assembly can be ...

  • Hobart 6614 ML-134050 - page 8

    – 8 – ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON. A T A D L A C I R T C E L E l e ...

  • Hobart 6614 ML-134050 - page 9

    – 9 – OPERA TION SAFETY DEVICES INCORPORATED IN THIS SAW MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SAW IS IN USE. SAFETY FEATURES Upper Guide and Guard Assembly Before turning the saw on, raise or lower the upper guide and guard assembly by grasping the hand knob and sliding up or down so the cutting zone is only as high as neces ...

  • Hobart 6614 ML-134050 - page 10

    – 10 – GAUGE PLATE When making several cuts of the same thickness (or when using the pusher plate), set the gauge plate as desired (Fig. 14) by pushing the lock lever and sliding the gauge plate to the thickness you want. A reference scale on the table indicates the thickness of cut. If the gauge plate is not needed, you may release the lock le ...

  • Hobart 6614 ML-134050 - page 11

    – 11 – CLEANING AND SANITIZING WARNING : DISCONNECT ELECTRICAL POWER AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON BEFORE CLEANING THIS MACHINE. The saw must be thoroughly cleaned and sanitized: Before first use; After each day's operation; Anytime it is not to be used for an extended period of time; or ...

  • Hobart 6614 ML-134050 - page 12

    – 12 – MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THE CIRCUIT IS BEING WORKED ON. LUBRICATION The motor has permanently lubricated ball bearings and requires no additional lubrication. The slide bar for the upper guide and guard assembly also requires no lubrication. After cleani ...

Fabbricante Hobart Categoria Saw

I documenti che otteniamo dal fabbricante del dispositivoHobart 6614 ML-134050 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Hobart
- manuali per l’uso 6614 ML-134050
- schede prodotto Hobart
- opuscoli
- o etichette energetiche Hobart 6614 ML-134050
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Hobart 6614 ML-134050.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Hobart 6614 ML-134050, manuali di manutenzione, brevi manuali o manuali utente Hobart 6614 ML-134050. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Hobart 6614 ML-134050.

Manuali per l’uso simili

Manuale completo del dispositivo Hobart 6614 ML-134050, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Hobart 6614 ML-134050 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Hobart 6614 ML-134050.

Il manuale per l’uso completo Hobart, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Hobart 6614 ML-134050 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Hobart 6614 ML-134050, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Hobart 6614 ML-134050 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Hobart 6614 ML-134050 - che ci dovrebbe aiutare nei primi passi durante l'uso Hobart 6614 ML-134050
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Hobart 6614 ML-134050
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Hobart 6614 ML-134050 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Hobart 6614 ML-134050?

Utilizza il modulo sottostante

Se non hai risolto il problema con Hobart 6614 ML-134050 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Hobart 6614 ML-134050 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)