-
La Crosse Technology WS-7013U-IT - page 1
1 WS-7013U-IT Wireless 915 MHz Temperature Station Instruction Manual ...
-
La Crosse Technology WS-7013U-IT - page 2
2 TABLE OF CONTENTS Topic Page Inventory of Contents Quick Setup Detailed Setup G uide Battery Installation Setting the Time Features Minimum and Maxi mum Temperatures Resetting Minimum and Maximum Temperatures Additional remote temperature sensors (optional) Mounting Troubleshootin g Maintenance and Car e Specifications Warranty Information ...
-
La Crosse Technology WS-7013U-IT - page 3
3 INVENTORY OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX29U- IT) and mounting bracket. (Figure 2) 3. 3 each, 1/2” Philips screws. 4. One strip of double sided adhesive tape. 5. Instruction Manual and Warranty Card. INSTANT TRANSMISSION is the s tate-of- the-art new wireless transmi ssion technology ...
-
La Crosse Technology WS-7013U-IT - page 4
4 ADDI TION AL EQU IPM ENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AAA 1.5V batteries. 3. 2 Fresh AA 1.5V batteries QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 1 ...
-
La Crosse Technology WS-7013U-IT - page 5
5 3. Place the batteries into the remote temperature sensor first then into the indoor temperature station. (All remote temperature sensors must be started before the indoor temperature station) 4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES. In this time the indoor temperature station and remote temperature sensor will start to talk to each other and ...
-
La Crosse Technology WS-7013U-IT - page 6
6 walls, floors, ceilings, thick trees, etc.) will effectively cut signal range in half. Example : A wireless weather station with a 330 feet range is mounted on an interior wall, so that the signal has to pass through one interior wall, one exterior wall, and across the 10 feet width of the room between the 2 walls. The first wall will reduce the ...
-
La Crosse Technology WS-7013U-IT - page 7
7 To complete the set up of your indoor temperature station after the 15 minutes have passed please follow the steps below. 1. Press and hold the “SET/CH” button for 5 seconds. Note: A “12h” or “24h” will appear on the top line. (“12h” for AM/PM, “24h” f or military time) 2. To change between “12h” and “24h” press and re ...
-
La Crosse Technology WS-7013U-IT - page 8
8 6 . When the correct hour is shown, press and release the “SET” button once. Press and release the SET button once more and you are done. DETAILED SETUP GUIDE BATTERY INST ALLATION - When one Temperature sensor is bein g used 1. First, insert the batteries to the Temperature sensor (see “ A. Temperature sensor ” below). 2. Within 2 minute ...
-
La Crosse Technology WS-7013U-IT - page 9
9 data signal from the sensor. The outdoor temperature and humidity should then be displayed on the Temperature Station. If this does not happen after 2 minutes, the batteries will need to be removed from both units and reset from step 1 and the signal reception icon is no longer shown. A. REMOTE TEMPERATURE SENSOR Remove the mounting bracket. a. R ...
-
La Crosse Technology WS-7013U-IT - page 10
10 a. Remove the battery cover on the backside. To do this, push up and pull out. b. Observing the correct polarity, install 2 AAA batteries. c. Replace battery cover. d. Wait 15 minutes to allow both the indoor and outdoor temperatures are shown on the indoor temperature station. Battery Cover ...
-
La Crosse Technology WS-7013U-IT - page 11
11 * When the signal is successfully received by the Temperature Station, the icon will be switched on. (If not successful, the icon will not be shown in LCD) So the user can easily see whether the last reception was successful (icon on) or not (icon off). On the other hand, the short blinking of the icon shows that a reception is being done now. ? ...
-
La Crosse Technology WS-7013U-IT - page 12
12 910MHz. This will also be done for re- synchronization. SETTING THE TIME 1. Press and hold the “ SET/CH” button for 5 second, “12h” will appear in the TIME LCD. 2. Press and release the “ MIN/ MAX ” button to select either 12h time (am/pm) or 24h time 3. Press and release the “ SET/CH” button 2 times, the hour will flash in the u ...
-
La Crosse Technology WS-7013U-IT - page 13
13 Note: if “12h” is selected, the temperature is displayed in degree Fahrenheit. If “24h” is selected, the temperature is displayed in degree Celsius FEATURES MINIMUM & M AXIMUM TEMPERATURES 1. Press and release the “ MIN/MA X ” button, “MIN” appears in the temperature LCD’s and the recorded minimum temperatures are displayed ...
-
La Crosse Technology WS-7013U-IT - page 14
14 temperature sensor units with the WS-7013U- IT. These extra sens ors can be purchased through the same dealer as this unit. 1. Remove all the batteries from the receiver and sensor(s) and wait 60 seconds. During these 60 seconds, press any button 20 times to discharge any excess pow er. 2. Insert the batteries to the first temperature sensor. 3. ...
-
La Crosse Technology WS-7013U-IT - page 15
15 5. Insert the batteries to the second sensor as soon as the outdoor temperature readings from the first sensor are displayed on the Temperature station. NOTE: You must insert the batteries into the second sensor w ithin 45 seconds of reception of the first sensor. 6. The outdoor temperature from the second sensor and the "channel 2" ic ...
-
La Crosse Technology WS-7013U-IT - page 16
16 NOTE: You must insert the batteries into the third sensor within 45 seconds of reception of the second sensor. IMPORTANT: Transmission problems will arise if the setting for multiple sensors is not followed as described above. Should transmission problems occur, it is necessary to remove the batteries from all units and start again the set-up fr ...
-
La Crosse Technology WS-7013U-IT - page 17
17 3. To reset the Minimum/Maximum readings, press and hold the “MIN/MAX” button for four seconds. MOUNTING Note: To achieve a true temperature rea ding, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on an outside North- facing wall. The sending range is 330ft; obstacles such as walls, concrete, an ...
-
La Crosse Technology WS-7013U-IT - page 18
18 b. Mount using either screws or adhesive tape. c. Reattach the temperature sensor to the mounting bracket. 2. TH E TEM PE R ATURE ST ATIO N e. The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand, all that is required is to place the indoor temperature station in an appropriate location. f ...
-
La Crosse Technology WS-7013U-IT - page 19
19 Problem: Th e LCD is faint Solution : Replace batteries Problem: No outdoor temperature I displayed. Solution : 1) Remove all batteries, reinsert into remote temperature sensor first, and then into the indoor temperature station. 2) Place remote temperature sensor closer to the indoor temperature station. 3) Be sure all batteries are fresh. 4) P ...
-
La Crosse Technology WS-7013U-IT - page 20
20 The indoor sensor is less responsive to ambient air currents because of the shielding effect of the display's case. In addition, the case can act as a heat sink to absorb and store heat from external sources (i.e. handling of the case or radiant heat). In addition, the much greater range of the outdoor temperature sensor requires a differen ...
-
La Crosse Technology WS-7013U-IT - page 21
21 9 Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology for repairs. SPECIFIC ATIONS Transmitting Frequency 915MHz Measuring Temperatures Indoor Temperature Station: Indoor 14.1 ° F to 139.8.2 ° F with 0.2 ° F resolution. (-9.9 ° C to 59.8 ° C with 0.1 ° C resolution) Indoor Temperature S ...
-
La Crosse Technology WS-7013U-IT - page 22
22 Indoor Temperature Station 2 x AAA, 1.5V Dimensions: (H x W x D) Indoor Temperature Station 4.3 x 2.75 x .92 in. (excluding table stand) (110 x 90 x 23.6 x mm) Remote Temperature Sensor 5.05 x 1.50 x 0.83 in. (128.3 x 38.2 x 21.2 mm) Battery life Approximately 24 months WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited war ...
-
La Crosse Technology WS-7013U-IT - page 23
23 authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technolog y, Ltd’s authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned part ...
-
La Crosse Technology WS-7013U-IT - page 24
24 ground return shipping charges to the o wner of the product to a USA address only. Your La Crosse Technology, Ltd warrant y covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or negl ect (including the lack of reasonable and necessary maintenance); (2) damage oc ...
-
La Crosse Technology WS-7013U-IT - page 25
25 misrepresentation by the seller or performance variations resulting from installation-related circumstances. LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE O PERATION OR MALF UNCTIO N OF THIS PRODUCT. THIS PR ODU CT IS NOT TO BE USED FOR MEDICAL PURPOSES O ...
-
La Crosse Technology WS-7013U-IT - page 26
26 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacrossetechnology.com Questions? Instructions? Please visit: www.lacrossetechnology.com/7013 All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or proc ...
-
La Crosse Technology WS-7013U-IT - page 27
27 FCC ID: OMOTX29U (sensor) RF Exposure mobile: The internal / external antennas used for this mobile sensor must provide a separation distance of at least 20 cm (8 inches) from all persons and must not be co-located or operating in conjunction with any other antenna or sensor." Statement according to FCC pa rt 15.19: This device complies wit ...
-
La Crosse Technology WS-7013U-IT - page 28
28 interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarante e that interference will not occur in a particular installation. If this equipm ...
Hai una domanda su La Crosse Technology WS-7013U-IT?
Utilizza il modulo sottostante
Se non hai risolto il problema con La Crosse Technology WS-7013U-IT con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con La Crosse Technology WS-7013U-IT è probabile che voglia condividere il modo di risolverlo.