Italiano dropdown-ico

Manuale per l’uso Pfaff 483

32 pagine 1.97 mb
Scarica

Vai alla pagina of 32

Summary
  • Pfaff 483 - page 1

    481 483 296-12-17 437 Justieranleitung engl. 1.97 Service manual ...

  • Pfaff 483 - page 2

    PFAFF 2 Contents Checking and adjustment ai d .................................................................................... . 3 1 Preliminary adjustment of the needle heigh t ............................................................ . 4 2 Zeroing the feed motio n ............................................................................ ...

  • Pfaff 483 - page 3

    3 PFAFF Notes on safety ● The machine must only be operated in full knowledge of the instruction book and by persons with appropriate training. ● Before commissioning the machine also read the motor manufacturer’s safety notes and instruction manual. ● The machine must only be used for the purpose intended. It must not be operated without t ...

  • Pfaff 483 - page 4

    PFAFF 3 Adjustment hole 1 = 0.6 mm past top dead center of the needle bar (0.6 past t.d.c.). Adjustment hole 3 = 0.6 mm past the bottom dead center of the needle bar (0.6 past b.d.c). Adjustment hole 4 = 1.8 mm past the bottom dead center of the needle bar (needle rise position). Adjustment hole 5 = top dead center of the needle bar (t.d.c. N). Adj ...

  • Pfaff 483 - page 5

    4 PFAFF 1 Preliminary adjustment of needle height Requirement With the needle bar at b.d.c. there must be a clearance of 16.5 mm between needle holder and needle plate. 2 1 ● Move needle bar 1 (screw 2 ) according to the requirement. Make sure that, when looking in the feed direction, the needle retaining screw points to the right. 16,5 mm ...

  • Pfaff 483 - page 6

    PFAFF 5 2 Zeroing the feed motion Requirement The feed dog must not move when turning the handwheel with the stitch length set at “0”. 2.1 Zeroing procedure with the gearbox closed ● Raise the presser foot and set the stitch length control lever 1 at its lowest position. ● Turn eccentric bushing 2 (screw 3 ) so that mark 4 is roughly at the ...

  • Pfaff 483 - page 7

    6 PFAFF 2.2 Zeroing procedure with the gearbox open ● Raise the presser foot and set the stitch length control lever 1 at its lowest position. ● Turn eccentric bushing 2 (screw 3 ) so that mark 4 is roughly at the bottom and the edge of the milled surface is at an angle of 45° to the machine front (for final adjustment see section 23). ● Tur ...

  • Pfaff 483 - page 8

    PFAFF 7 3 Zeroing the needle feed motion (Adjustment not applicable to Pfaff 483) Requirement: With the stitch length control set at “0” the needle bar should make no feed motion when the handwheel is turned. ● Adjust needle feed regulating crank 1 (screw 2 ) according to the requirement. Adjustment aid: Insert a screwdriver in needle feed dr ...

  • Pfaff 483 - page 9

    8 PFAFF 4 Feed lifting motion Requirement With the stitch length set at “0” the feed dog should be at t.d.c. when the needle bar is at a position 0.6 mm past b.d.c (cylindrical pin in hole “3”; for PFAFF 481 ) or 0.6 mm past t.d.c (cylindrical pin in hole “1”; for PFAFF 483 ). In this position, the notch in feed lifting eccentric 1 shou ...

  • Pfaff 483 - page 10

    PFAFF 9 5 Feed dog height Requirement With the stitch length set at “0” and the needle bar at a position 0.6 mm past b.d.c (cylindrical pin in hole “3”, for PFAFF 481 ) and 0.6 past t.d.c. (cylindrical pin in hole “1”; for PFAFF 483 ) 1. the feed dog must be positioned in the middle of the needle plate slots when looked at from the side ...

  • Pfaff 483 - page 11

    10 PFAFF 6 Feed driving motion Requirement With the longest stitch length set and the needle bar at 0.6 mm past b.d.c. (cylindrical pin in hole “3”; for PFAFF 481 ) the needle bar at 0.6 mm past t.d.c. (cylindrical pin in hole “1”; for PFAFF 483 ) the feed dog should not move when the reverse-feed control is moved up and down. ● Turn feed ...

  • Pfaff 483 - page 12

    PFAFF 11 7 Timing the needle feed motion (Adjustment not applicable to PFAFF 483) Requirement Both the needle bar and the feed dog should remain motionless when reverse-feed control 3 is moved up and down with the machine set for its longest stitch and the needle bar set 0.6 mm past its b.d.c. (cylindrical pin in hole “3”). ● Turn feed drivin ...

  • Pfaff 483 - page 13

    12 PFAFF ● Set the stitch length at “0” and position the needle right above the needle hole. ● Loosen screws 1 and 2 . ● Position needle bar frame 3 both lengthwise and crosswise of the sewing direction according to the requirement and tighten screw 1 . ● Turn the handwheel a few turns to ensure that the needle bar is not under stress i ...

  • Pfaff 483 - page 14

    PFAFF 13 ● Position the needle bar just above the needle hole. ● Loosen screws 1, 2 and 3 . ● Position needle bar frame 4 both lengthwise and crosswise of the sewing direction according to the requirement and tighten screw 2 just lightly and screw 3 firmly. ● Turn screw 1 to move the guide pin behind this screw towards the eye of the needle ...

  • Pfaff 483 - page 15

    14 PFAFF 9 Eccentric hook shaft bearing and hook-to-needle clearance ● Loosen screws 1 and 2 . ● Turn bearing 3 according to requirement 1. ● Set the hook lightly against spin disc 4 , shift bearing 3 - without turning it - according to requirement 2 and tighten screws 1 and 2 . ● Position gear 5 (screws 6 ) according to requirement 3. 3 6 ...

  • Pfaff 483 - page 16

    PFAFF 15 10 Needle rise, final adjustment of needle bar height and bobbin case positioning finger Requirement With the stitch length set at “0” and the needle bar at a position 1.8 mm past b.d.c. (cylindrical pin in hole “4”) 1. the hook point must be opposite the center line of the needle and the top edge of the needle eye must be 0.8 mm b ...

  • Pfaff 483 - page 17

    16 PFAFF 11 Vertical position of bobbin case opener Requirement 1. Small hook (481 and 483) At the left point of reversal of bobbin case opener 3 the bobbin case opener finger must be roughly on one level with the lug of bobbin case base 4 . 2. Large hook (481G and 483G) At the left point of reversal of bobbin case opener 3 the top edge of the bobb ...

  • Pfaff 483 - page 18

    PFAFF 17 12 Position of bobbin case opener Requirement 1. Small hook (481 and 483) With bobbin case opener 3 in its left point of reversal there must be a clearance of approx. 0.8 mm between the front edge of the bobbin case opener finger and the edge of bobbin case base 6 . 2. Large hook (481 and 483) At the left point of reversal of bobbin case o ...

  • Pfaff 483 - page 19

    18 PFAFF 13 Timing the bobbin case opener Requirement In needle bar position 1.8 mm past b.d.c. (cylindrical pin in hole “4”) bobbin case opener finger must be at its right point of reversal. ● Adjust bobbin case opener eccentric 1 (screws 2 ) according to the requirement. Adjustment aid: To facilitate checking insert a screwdriver in the slo ...

  • Pfaff 483 - page 20

    PFAFF 19 14 Clearance between presser foot and needle plate Requirement With presser bar lifter 1 raised there must be a clearance of 5 mm between presser foot and needle plate. Note: When the presser foot is raised to its top position upon actuating the knee lever fully or by means of the automatic presser foot lift -910/.. there must not be any c ...

  • Pfaff 483 - page 21

    20 PFAFF 15 Eliminating feed differences (Adjustment not applicable to PFAFF 483) Requirement With the machine set for its longest stitch, both the feed dog and and the needle must make feed strokes of the same length when the handwheel is turned. ● Shift hinge stud 1 (nut 2 ) to adjust the feed stroke of the needle feed. ● Check whether the ne ...

  • Pfaff 483 - page 22

    PFAFF 21 16 Tension release mechanism Requirement When presser bar lifter 1 is raised both tension discs must be at least 0.5 mm apart. ● Adjust tension release lever 2 (screw 3 ) according to the requirement. ● Lower the presser foot onto the needle plate. Now the tension must be fully activated. 0,5 mm 3 2 1 ...

  • Pfaff 483 - page 23

    22 PFAFF 17 Thread check spring and thread regulator Requirement 1. Thread check spring 3 must have moved by its full stroke by the time the point of the needle enters the material (stroke approx. 7 mm ). 2. Thread regulator 4 must be fixed in the elongated hole so that thread check spring 3 moves by 1 mm by the time the hook has widened the thread ...

  • Pfaff 483 - page 24

    PFAFF 23 18 Knee lever resting position Requirement When at rest, knee lever connecting rod 2 must be at right angles with the bedplate. ● Raise the presser foot by means of the presser bar lifter. ● Push the knee lever joint on knee lever shaft 1 and let the connecting rod 2 engage in the joint. ● Turn stop screw 3 (nut 4 ) according to the ...

  • Pfaff 483 - page 25

    24 PFAFF 19 Knee lever play Requirement When the presser foot is resting on the needle plate, there must be a clearance of 1.3 mm between lifting lever 3 and lifting piece 4 . ● Position the needle at its b.d.c. and let the presser foot down on the needle plate. ● Turn crank 1 (screws 2 ) according to the requirement. Make sure the vertical kne ...

  • Pfaff 483 - page 26

    PFAFF 25 20 Adjusting the knee lever motion Requirement When the knee lever is pushed by the full amount of its travel, there must be a clearance as indicated in the table below between presser foot and needle plate and the presser bar lifter should drop by its own weight. Version A and subclass -731/..: 7 mm Versions B and C: 9 mm ● Turn stop sc ...

  • Pfaff 483 - page 27

    26 PFAFF 21 Bobbin winder Requirement When the bobbin winder is engaged, the winder spindle should be driven reliably; when the bobbin winder is disengaged, however, drive wheel 1 must not contact friction wheel 5 . The bobbin winder should stop automatically when the thread wound on the bobbin has reached a point about 1.0 mm below the bobbin rim. ...

  • Pfaff 483 - page 28

    PFAFF 27 22 Limiting the stitch length ● Loosen screw 1 (accessible through the assembly hole) or turn it out according to the limit to be set. ● Set stitch length control lever 2 at the desired maximum stitch length. ● Set limiting angle 3 from above against control lever 2 and fix it (in the desired position) by tightening screw 1 in either ...

  • Pfaff 483 - page 29

    28 PFAFF 23 Matching forwards and reverse stitch lengths Requirement When the stitch length is set at “3” the forwards feed must match the reverse feed. ● Turn bush 1 (screw 2 ) in accordance with the requirement. Make sure that the eccentricity of bush 1 points downwards. 1 2 ...

  • Pfaff 483 - page 30

    PFAFF 29 ● Turn screw 1 according to the requirement. 1 24 Presser foot pressure Requirement Proper feeding of the material must be ensured even at top sewing speed. There must Contents ...

  • Pfaff 483 - page 31

    Notes ...

  • Pfaff 483 - page 32

    G.M. PFAFF Aktiengesellschaft Postfach 3020 D-67653 Kaiserslautern Königstr. 154 D-67655 Kaiserslautern Telefon: (0631) 200-0 Telefax: (0631) 172 02 Telex: 45753 PFAFF D Gedruckt in der BRD Printed in Germany Imprimé en R.F.A. Impreso en la R.F.A. Stampato in R.F.G. ïô Ð e aôa Ç ï ÖÑÃ ...

Fabbricante Pfaff Categoria Sewing Machine

I documenti che otteniamo dal fabbricante del dispositivoPfaff 483 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Pfaff
- manuali per l’uso 483
- schede prodotto Pfaff
- opuscoli
- o etichette energetiche Pfaff 483
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Pfaff 483.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Pfaff 483, manuali di manutenzione, brevi manuali o manuali utente Pfaff 483. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Pfaff 483.

Manuali per l’uso simili

Manuale completo del dispositivo Pfaff 483, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Pfaff 483 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Pfaff 483.

Il manuale per l’uso completo Pfaff, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Pfaff 483 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Pfaff 483, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Pfaff 483 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Pfaff 483 - che ci dovrebbe aiutare nei primi passi durante l'uso Pfaff 483
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Pfaff 483
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Pfaff 483 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Pfaff 483?

Utilizza il modulo sottostante

Se non hai risolto il problema con Pfaff 483 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Pfaff 483 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)