Italiano dropdown-ico

Manuale per l’uso Delta (Model 31-695)

21 pagine 1.15 mb
Scarica

Vai alla pagina of 21

Summary
  • Delta (Model 31-695) - page 1

    INSTRUCTION MANUAL P ART NO. 902122 - 02-20-04 Copyright © 2004 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 6" Belt / 9" Disc Sander (Model 31-69 ...

  • Delta (Model 31-695) - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta (Model 31-695) - page 3

    3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. WEAR EYE PROTECTION. AL WA YS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is d ...

  • Delta (Model 31-695) - page 4

    4 ADDITIONAL SAFETY RULES FOR ABRASIVE FINISHING MACHINES 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury . 2. OBT AIN ADVICE from your supervisor , instructor , or another qualified person if you are not thor oughly familiar with ...

  • Delta (Model 31-695) - page 5

    5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta (Model 31-695) - page 6

    6 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wire extension cor d which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized ...

  • Delta (Model 31-695) - page 7

    7 Fig. 2 1. Sander with 6" x 48" Sanding Belt and Backstop 2. Sanding Disc Plate 3. Belt and Pulley Cover 4. 9" Sanding Disc 5. Plug 6. T -Wrench 7. Drive Belt 8. M6 x 55mm Hex Socket Head Screws (2) 9. M6.4 Flat Washer (2 10. M6.4 Lockwasher (2) 11. Disc Cover 12. M4.2 x 13mm Panhead Screws (3) 13. Support Rod 14. T able Assembly 1 ...

  • Delta (Model 31-695) - page 8

    8 For your own safety , do not connect the machine to the power source until the machine is completely assembled and you read and understand the entir e instruction manual. ASSEMBL Y ST AND Any letter designations that are stamped on the braces of the stand are for pr oduction purposes ONL Y and are not used for assembling the stand. Follow the ins ...

  • Delta (Model 31-695) - page 9

    9 BEL T AND PULLEY GUARD Place an M6.4 lockwasher and an M6.4 flat washer in that order on two M6 x 55mm hex socket head scr ews (B), and attach the belt and pulley guard (A) Fig. 8 to the machine. NOTE: Install the plug (C) in the guard. C SANDING DISC PLA TE 1. Place the key (C) Fig. 9 into the keyway of the driveshaft and slide the sanding disc ...

  • Delta (Model 31-695) - page 10

    10 Fig. 13 LOWER COVER FOR SANDING DISC Use three M4.2 x 13mm pan head scr ews (C) to attach the lower cover (A) Fig. 13 to the belt and pulley guard (B). Prevent the sanding disc fr om contacting the lower cover . Rotate the sanding disc by hand to ensure that no contact is made. C NOTE: Fig. 14 Fig. 15 SANDER T ABLE 1. Insert the support r od (A) ...

  • Delta (Model 31-695) - page 11

    11 Fig. 17 LOCKING SWITCH IN THE “OFF” POSITION When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. This can be done by grasping the switch toggle (B) and pulling it out of the switch, as shown in Fig. 20. With the switch toggle (B) removed, the switch will not operate. However , sh ...

  • Delta (Model 31-695) - page 12

    12 Fig. 21 Fig. 22 ADJUSTING BACKSTOP SQUARE WITH SANDING BEL T 1. Before making this adjustment, check to see that the belt tension lever (A) Fig. 22 is all the way to the left in the “tighten” position. 2. Place a square (B) Fig. 23 on the sanding belt with the end of the square against the backstop. 3. If the backstop is not square with the ...

  • Delta (Model 31-695) - page 13

    13 SQUARING T ABLE WITH SANDING DISC 1. Place one end of a combination square (C) Fig. 25 on the table with the other end against the sanding disc. 2. If the table surface is not 90 degrees to the disc, loosen the table lock knob (A) Fig. 25, adjust the table, and tighten lock knob (A). 3. Adjust the pointer (B) Fig. 25 to the “0” degree mark o ...

  • Delta (Model 31-695) - page 14

    14 Fig. 30 Fig. 31 USING T ABLE ASSEMBL Y WITH SANDING BEL T Use the table assembly with the sanding belt in the vertical position ONL Y. T o move the table assembly (B) Fig. 30 to the sanding arm (A): 1. Remove the backstop (C) Fig. 30. 2. Loosen the screw (D) Fig. 30 and car efully remove support bar (E) and table assembly (B) from the disc unit. ...

  • Delta (Model 31-695) - page 15

    15 2. If you are sanding with the belt, pull the dust shield (A) Fig. 34 outward. Fig. 35 Fig. 36 WRENCH STORAGE A hole is provided in the stand for storing the hex wr ench (A) Fig. 35, supplied with the sander . REMOVING UPPER SANDING DRUM GUARD Y ou can remove the upper sanding drum guard (A) Fig. 36 to sand inside curved work or to change the be ...

  • Delta (Model 31-695) - page 16

    16 Fig. 39 Fig. 40 5. Place a new 6" x 48" sanding belt (F) Fig. 40 over both sanding drums (G). Ensure that the belt will travel in the direction of the arr ows printed on the inside of the belt. 6. Move the tension lever (E) Fig. 39 left to the “TIGHTEN” position. 7. Replace the support bracket, backstop and upper sanding drum guard ...

  • Delta (Model 31-695) - page 17

    17 Fig. 45 Fig. 44 SURF ACING OR EDGE SANDING WITH SANDING BEL T When surfacing (Fig. 44) or edge sanding (Fig. 45), place the sanding arm in the horizontal position and use the backstop (A) Fig. 44 and Fig. 45 to keep the workpiece in place. Hold the workpiece firmly and keep your fingers away from the sanding belt. Place the end of the workpiece ...

  • Delta (Model 31-695) - page 18

    18 Fig. 48 END SANDING WITH THE DISC When sanding the ends of narrow workpieces, use the sanding disc and the accessory miter gauge (Fig. 48). Move the work from the center to the left side of the sanding disc. Always sand on the left (downward) side of the sanding disc. Sanding on the right (upwar d) side of the sanding disc could cause the workpi ...

  • Delta (Model 31-695) - page 19

    19 MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. W ear ANSI Z87.1 safety glasses while using compressed air . F AILURE TO ST ART Shoul ...

  • Delta (Model 31-695) - page 20

    20 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra ...

  • Delta (Model 31-695) - page 21

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Fabbricante Delta Categoria Sander

I documenti che otteniamo dal fabbricante del dispositivoDelta (Model 31-695) possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Delta
- manuali per l’uso (Model 31-695)
- schede prodotto Delta
- opuscoli
- o etichette energetiche Delta (Model 31-695)
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Delta (Model 31-695).

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Delta (Model 31-695), manuali di manutenzione, brevi manuali o manuali utente Delta (Model 31-695). A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Delta (Model 31-695).

Manuali per l’uso simili

Manuale completo del dispositivo Delta (Model 31-695), come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Delta (Model 31-695) dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Delta (Model 31-695).

Il manuale per l’uso completo Delta, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Delta (Model 31-695) - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Delta (Model 31-695), FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Delta (Model 31-695) che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Delta (Model 31-695) - che ci dovrebbe aiutare nei primi passi durante l'uso Delta (Model 31-695)
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Delta (Model 31-695)
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Delta (Model 31-695) in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Delta (Model 31-695)?

Utilizza il modulo sottostante

Se non hai risolto il problema con Delta (Model 31-695) con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Delta (Model 31-695) è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)