日本語 dropdown-ico

Delta (Model 31-695)の取扱説明書

21ページ 1.15 mb
ダウンロード

ページに移動 of 21

Summary
  • Delta (Model 31-695) - page 1

    INSTRUCTION MANUAL P ART NO. 902122 - 02-20-04 Copyright © 2004 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 6" Belt / 9" Disc Sander (Model 31-69 ...

  • Delta (Model 31-695) - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta (Model 31-695) - page 3

    3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. WEAR EYE PROTECTION. AL WA YS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is d ...

  • Delta (Model 31-695) - page 4

    4 ADDITIONAL SAFETY RULES FOR ABRASIVE FINISHING MACHINES 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury . 2. OBT AIN ADVICE from your supervisor , instructor , or another qualified person if you are not thor oughly familiar with ...

  • Delta (Model 31-695) - page 5

    5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta (Model 31-695) - page 6

    6 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wire extension cor d which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized ...

  • Delta (Model 31-695) - page 7

    7 Fig. 2 1. Sander with 6" x 48" Sanding Belt and Backstop 2. Sanding Disc Plate 3. Belt and Pulley Cover 4. 9" Sanding Disc 5. Plug 6. T -Wrench 7. Drive Belt 8. M6 x 55mm Hex Socket Head Screws (2) 9. M6.4 Flat Washer (2 10. M6.4 Lockwasher (2) 11. Disc Cover 12. M4.2 x 13mm Panhead Screws (3) 13. Support Rod 14. T able Assembly 1 ...

  • Delta (Model 31-695) - page 8

    8 For your own safety , do not connect the machine to the power source until the machine is completely assembled and you read and understand the entir e instruction manual. ASSEMBL Y ST AND Any letter designations that are stamped on the braces of the stand are for pr oduction purposes ONL Y and are not used for assembling the stand. Follow the ins ...

  • Delta (Model 31-695) - page 9

    9 BEL T AND PULLEY GUARD Place an M6.4 lockwasher and an M6.4 flat washer in that order on two M6 x 55mm hex socket head scr ews (B), and attach the belt and pulley guard (A) Fig. 8 to the machine. NOTE: Install the plug (C) in the guard. C SANDING DISC PLA TE 1. Place the key (C) Fig. 9 into the keyway of the driveshaft and slide the sanding disc ...

  • Delta (Model 31-695) - page 10

    10 Fig. 13 LOWER COVER FOR SANDING DISC Use three M4.2 x 13mm pan head scr ews (C) to attach the lower cover (A) Fig. 13 to the belt and pulley guard (B). Prevent the sanding disc fr om contacting the lower cover . Rotate the sanding disc by hand to ensure that no contact is made. C NOTE: Fig. 14 Fig. 15 SANDER T ABLE 1. Insert the support r od (A) ...

  • Delta (Model 31-695) - page 11

    11 Fig. 17 LOCKING SWITCH IN THE “OFF” POSITION When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. This can be done by grasping the switch toggle (B) and pulling it out of the switch, as shown in Fig. 20. With the switch toggle (B) removed, the switch will not operate. However , sh ...

  • Delta (Model 31-695) - page 12

    12 Fig. 21 Fig. 22 ADJUSTING BACKSTOP SQUARE WITH SANDING BEL T 1. Before making this adjustment, check to see that the belt tension lever (A) Fig. 22 is all the way to the left in the “tighten” position. 2. Place a square (B) Fig. 23 on the sanding belt with the end of the square against the backstop. 3. If the backstop is not square with the ...

  • Delta (Model 31-695) - page 13

    13 SQUARING T ABLE WITH SANDING DISC 1. Place one end of a combination square (C) Fig. 25 on the table with the other end against the sanding disc. 2. If the table surface is not 90 degrees to the disc, loosen the table lock knob (A) Fig. 25, adjust the table, and tighten lock knob (A). 3. Adjust the pointer (B) Fig. 25 to the “0” degree mark o ...

  • Delta (Model 31-695) - page 14

    14 Fig. 30 Fig. 31 USING T ABLE ASSEMBL Y WITH SANDING BEL T Use the table assembly with the sanding belt in the vertical position ONL Y. T o move the table assembly (B) Fig. 30 to the sanding arm (A): 1. Remove the backstop (C) Fig. 30. 2. Loosen the screw (D) Fig. 30 and car efully remove support bar (E) and table assembly (B) from the disc unit. ...

  • Delta (Model 31-695) - page 15

    15 2. If you are sanding with the belt, pull the dust shield (A) Fig. 34 outward. Fig. 35 Fig. 36 WRENCH STORAGE A hole is provided in the stand for storing the hex wr ench (A) Fig. 35, supplied with the sander . REMOVING UPPER SANDING DRUM GUARD Y ou can remove the upper sanding drum guard (A) Fig. 36 to sand inside curved work or to change the be ...

  • Delta (Model 31-695) - page 16

    16 Fig. 39 Fig. 40 5. Place a new 6" x 48" sanding belt (F) Fig. 40 over both sanding drums (G). Ensure that the belt will travel in the direction of the arr ows printed on the inside of the belt. 6. Move the tension lever (E) Fig. 39 left to the “TIGHTEN” position. 7. Replace the support bracket, backstop and upper sanding drum guard ...

  • Delta (Model 31-695) - page 17

    17 Fig. 45 Fig. 44 SURF ACING OR EDGE SANDING WITH SANDING BEL T When surfacing (Fig. 44) or edge sanding (Fig. 45), place the sanding arm in the horizontal position and use the backstop (A) Fig. 44 and Fig. 45 to keep the workpiece in place. Hold the workpiece firmly and keep your fingers away from the sanding belt. Place the end of the workpiece ...

  • Delta (Model 31-695) - page 18

    18 Fig. 48 END SANDING WITH THE DISC When sanding the ends of narrow workpieces, use the sanding disc and the accessory miter gauge (Fig. 48). Move the work from the center to the left side of the sanding disc. Always sand on the left (downward) side of the sanding disc. Sanding on the right (upwar d) side of the sanding disc could cause the workpi ...

  • Delta (Model 31-695) - page 19

    19 MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. W ear ANSI Z87.1 safety glasses while using compressed air . F AILURE TO ST ART Shoul ...

  • Delta (Model 31-695) - page 20

    20 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warra ...

  • Delta (Model 31-695) - page 21

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

メーカー Delta カテゴリー Sander

Delta (Model 31-695)のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- (Model 31-695)の取扱説明書
- Deltaの製品カード
- パンフレット
- またはDelta (Model 31-695)の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Delta (Model 31-695)の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Delta (Model 31-695)の取り付け説明書、サービスマニュアル、簡易説明書、またはDelta (Model 31-695)のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Delta (Model 31-695)の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Delta (Model 31-695)デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDelta (Model 31-695)を使用するのを助ける技術的文書のことです。説明書は通常、全てのDelta (Model 31-695)ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Deltaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Delta (Model 31-695)の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDelta (Model 31-695)の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Delta (Model 31-695)に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Delta (Model 31-695)デバイスの基本機能を使うにあたってのヒント。 Delta (Model 31-695)のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Delta (Model 31-695)に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDelta (Model 31-695)のメーカー/サービスへの連絡先に関する情報。

Delta (Model 31-695)についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもDelta (Model 31-695)の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta (Model 31-695)で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)