Pelco C2928M-QSの取扱説明書

16ページ 0.93 mb
ダウンロード

ページに移動 of 16

Summary
  • Pelco C2928M-QS - page 1

    QUICK START GUIDE C2928M-QS (7/05) PMCD750 DLP ™ Display 50-Inch Rear Projection Display ...

  • Pelco C2928M-QS - page 2

    2 C2928M-QS (7/05) This quick start guide describes basic assembly and operation of the PMCD750 DLP ™ display as a stand-alone unit and as part of a video wall. BEFORE Y OU BEGIN DOCUMENTATION Refer to the enclosed CD for the following documentation: • Installation/Operation manual • Copy of this Quick Start Guide ...

  • Pelco C2928M-QS - page 3

    C2928M-QS (7/05) 3 Chassis Assembly Unpack the PMCD750 unit. The screen is not needed yet and should be left in its container at this time. SINGLE DISPLAY Attach the screen support to the front edge of the chassis with the supplied screen support bolts. The screen support mounts only one way . It incorporates a stop (rest) for the screen. Refer to ...

  • Pelco C2928M-QS - page 4

    4 C2928M-QS (7/05) W ALL DISPLAY – SECOND ROW AND UP Figure 2. T ie-Back Connection Points DANGER: Because the PMCD750 unit has a narrow front-to-back profile, the danger of tipping exists with high walls. For walls over two units high and all tilted walls, use the four tie-back points (1/4-20 threaded holes) on the rear of the unit to secure th ...

  • Pelco C2928M-QS - page 5

    C2928M-QS (7/05) 5 1. Stack another row of PMCD750 units on the first row . As you stack, be careful inserting the alignment pins on the second row chassis into the alignment holes on the lower unit. Refer to Figure 3. Figure 3. Alignment Pin Locations (Front View) WARNING: The maximum stack height for a wall is four units. ALIGNMENT PINS FIRST RO ...

  • Pelco C2928M-QS - page 6

    6 C2928M-QS (7/05) 2. As each unit is placed in the second row , secure it to the front of the lower unit with two 6-32 x 3/8-inch screws. Refer to Figure 4. Figure 4. Front Screw Securing Locations FRONT SCREW CONNECTION POINTS FRONT SCREW CONNECTION POINT DET AIL ...

  • Pelco C2928M-QS - page 7

    C2928M-QS (7/05) 7 3. Bolt the PMCD750 units together vertically through the vertical connection points using the 1/4-20 x 3/8-inch bolts. Refer to Figure 5. 4. Bolt the PMCD750 units together through the bottom connection points the same as the first row . Refer to Figure 1. 5. Bolt the PMCD750 units together through the horizontal connection poi ...

  • Pelco C2928M-QS - page 8

    8 C2928M-QS (7/05) Connecting Analog and Digital Sources The PMCD750 will accept video input from devices with VGA or DVI output. Video sources with either or both of these output types can have their images displayed on the PMCD750. Refer to Figure 6. Figure 6. Video Input Connections Connect the video input to the Analog 1, Analog 2, or Digital I ...

  • Pelco C2928M-QS - page 9

    C2928M-QS (7/05) 9 Connecting RS-232 and RS-485 Control Serial control can be used with stand-alone units, a wall, or several walls. To connect an external controller: 1. Using a straight-through computer serial cable, connect the RS-232 input of the stand-alone unit or the first unit in the wall to the serial out port of the external control devi ...

  • Pelco C2928M-QS - page 10

    10 C2928M-QS (7/05) Installing Screens To install a screen on a stand-alone unit, follow the instructions in steps 1a, 1b, and 1c. 1. T o install the PMCD750 screens, start in the middle of the bottom row and install that screen. The screen supports should be installed on the bottom row of PMCD750 screens. a. Pull the screen rails all the way out o ...

  • Pelco C2928M-QS - page 11

    C2928M-QS (7/05) 11 Figure 9. L-Shaped Screen Slot ...

  • Pelco C2928M-QS - page 12

    12 C2928M-QS (7/05) Connecting Power 1. Bring AC power next to the electronics module. Connect the power to the receptacle located on the rear panel. The voltage can be 115 V AC (90–132 VAC) or 230 V AC (200–254 V AC). Refer to Figure 10. Figure 10. Power Switch and Receptacles 2. The AC power can be looped through to the next PMCD750 unit, res ...

  • Pelco C2928M-QS - page 13

    C2928M-QS (7/05) 13 Using The Remote Control Using the the remote control is the only way to access menu settings. There are no access controls on the display unit. The remote control projects a series of IR (infrared) pulses to the PMCD750 display for control. Aim the remote control at a single display and press MENU. The main menu should be visib ...

  • Pelco C2928M-QS - page 14

    14 C2928M-QS (7/05) Alignment and Adjustment If the image on the screen is not positioned accurately , alignment of the optical engine may be required. It is important to check this mechanical adjustment of the optical engine before any electronic adjustments are made to the picture. Refer to the Aligning the Optical Engine section of the Installat ...

  • Pelco C2928M-QS - page 15

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series ...

  • Pelco C2928M-QS - page 16

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

メーカー Pelco カテゴリー Projection Television

Pelco C2928M-QSのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- C2928M-QSの取扱説明書
- Pelcoの製品カード
- パンフレット
- またはPelco C2928M-QSの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pelco C2928M-QSの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pelco C2928M-QSの取り付け説明書、サービスマニュアル、簡易説明書、またはPelco C2928M-QSのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pelco C2928M-QSの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pelco C2928M-QSデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPelco C2928M-QSを使用するのを助ける技術的文書のことです。説明書は通常、全てのPelco C2928M-QSユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pelcoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pelco C2928M-QSの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPelco C2928M-QSの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pelco C2928M-QSに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pelco C2928M-QSデバイスの基本機能を使うにあたってのヒント。 Pelco C2928M-QSのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pelco C2928M-QSに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPelco C2928M-QSのメーカー/サービスへの連絡先に関する情報。

Pelco C2928M-QSについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPelco C2928M-QSの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPelco C2928M-QSで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)