Pelco C2434Mの取扱説明書

16ページ 0.28 mb
ダウンロード

ページに移動 of 16

Summary
  • Pelco C2434M - page 1

    CC5BCBW Series Heavy-Duty Spectra ® Back Box Installation Manual C2434M (7/01) Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120 ® ...

  • Pelco C2434M - page 2

    2 Pelco Manual C2434M (7/01) IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be obser ved. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X ,6 o ...

  • Pelco C2434M - page 3

    Pelco Manual C2434M (7/01) 3 DESCRIPTION The Heavy-Duty Spectra is perfect for installations where structural integrity and vandalism are a prior ity . The system features hea vy-duty constr uction and tamper-resistant barrel ke y locks . The in-ceiling model has a reinforced brac ket mounting system for installation in a fixed ceiling. Pendant mod ...

  • Pelco C2434M - page 4

    4 Pelco Manual C2434M (7/01) 00535 SPRING CLIP 8-32X.275 INCH SCREW 00537 00530 00531 00532 CEILIN G MOUNTING RING S 00533 AT TA C H S A F E T Y CHAIN HERE 00534 INST ALLA TION OF IN-CEILING MODEL STEP 1 - PREP ARE CEILING a. Locate the center point of the mount- ing location. Drill a hole in the ceiling using a 3/32-inch drill. b. Insert the compa ...

  • Pelco C2434M - page 5

    Pelco Manual C2434M (7/01) 5 LABEL SW1 L A B E L S W 2 SW1 SW2 RS-422 TERMINA TION SWITCH ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 SW2 00538 GREEN T AB RED T AB 00539 BARREL KEY LOCK BALL STUD RECEIVER BALL STUD 00497 TRIM LEASH TO USE YOUR DOME, REFER TO THE OPERA TION AND PROGRAMMING MANUAL. +5 to +24 VDC NOT USED NOT USED TX- TX+ VIDEO IN CONTROLLE ...

  • Pelco C2434M - page 6

    6 Pelco Manual C2434M (7/01) INST ALLA TION OF PENDANT MODELS STEP 1 - DISASSEMBLE BACK BOX a. Tu rn the thumbscre w and open the hinged door located inside the back box. 01082 01081 01080 b. Unscrew the three Phillips scre ws located under neath the hinged door . Remove the inside portion of the back box. c. Remov e the inside mounting plate by lo ...

  • Pelco C2434M - page 7

    Pelco Manual C2434M (7/01) 7 STEP 3 - INST ALL THE BACK BOX 01079 01078 a. Secure the conduit fitting to the hole located on the inside base of the octagonal back box. b. Pull the cable and wiring for the system through the octagonal back box and conduit fitting. Mount the back bo x to the mounting surface , cor ner , or pole mount. c. Thread the c ...

  • Pelco C2434M - page 8

    8 Pelco Manual C2434M (7/01) STEP 5 - INST ALL DOME DRIVE LABEL SW1 L A B E L S W 2 SW1 SW2 RS-422 TERMINA TION SWITCH ON 1 2 3 4 5 6 7 8 ON 1 2 3 4 5 6 7 8 SW2 00538 a. Set the DIP switches f or SW1 and SW2 on the bottom of the dome drive for the appropriate receiver address. Refer to the labels on the dome drive or T ables C through E in the Appe ...

  • Pelco C2434M - page 9

    Pelco Manual C2434M (7/01) 9 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Unit does not operate. The controller is not communicating with the Spectra unit. Fan does not operate. Ve r tical roll on monitor when switching between cameras. DOME 1 POWER DOME 2 POWER DOME 3 POWER Check to see if the red LED on the circuit board in the back box is lit ...

  • Pelco C2434M - page 10

    10 Pelco Manual C2434M (7/01) APPENDIX Ta b le A. Video Coaxial Cable Requirements Cable T ype* Maximum Distance RG59/U 750 ft (229 m) RG6/U 1,000 ft (305 m) RG11/U 1,500 ft (457 m) * Minimum cable requirements: 75 ohms impedance. All-copper center conductor . 95% braided copper shield. Ta b le B. 24 V A C Wiring Distances The follo wing are the re ...

  • Pelco C2434M - page 11

    Pelco Manual C2434M (7/01) 11 Ta b le D. Switch Settings f or SW2 – P-T ype Control NOTE: F or Coaxitron controls , SW2 is not used; set all s witches OFF . For D-type control systems , refer to T able E. Baud Rate Switch Setting SW2-6 SW2-7 SW2-8 2400 OFF OFF OFF 4800 ON OFF OFF 9600 OFF ON OFF Receiver Switch Setting Address SW2-1 SW2-2 SW2-3 S ...

  • Pelco C2434M - page 12

    12 Pelco Manual C2434M (7/01) Ta b le E. Switch Settings for SW2 – D-T ype Control (continued) (Continued on next page) Receiver Switch Setting Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 49 ON OFF OFF OFF ON ON OFF OFF 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON OFF ON ON OFF OFF 53 ON OFF ON OFF ON O ...

  • Pelco C2434M - page 13

    Pelco Manual C2434M (7/01) 13 Ta b le E. Switch Settings for SW2 – D-T ype Control (continued) Receiver Switch Setting Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 161 ON OFF OFF OFF OFF ON OFF ON 162 OFF ON OFF OFF OFF ON OFF ON 163 ON ON OFF OFF OFF ON OFF ON 164 OFF OFF ON OFF OFF ON OFF ON 165 ON OFF ON OFF OFF ON OFF ON 166 OFF ON ...

  • Pelco C2434M - page 14

    14 Pelco Manual C2434M (7/01) SPECIFICA TIONS MECHANICAL Construction Back box: Aluminum Dome drive: Aluminum, ABS plastic Lower dome: Acrylic Cable Entry In-Ceiling: .75-inch (1.91 cm) conduit fitting Pendant: Through 1.5-inch (3.81 cm) NPT pendant mount Pan Movement: 360 ° continuous pan rotation Vertical Tilt: Unobstructed +2 ° to -92 ° Manua ...

  • Pelco C2434M - page 15

    Pelco Manual C2434M (7/01) 15 GENERAL Environment In-Ceiling: Indoor only Pendant: Indoor/outdoor Operating Range In-Ceiling: 32 to 122 ° F (0 to 50 ° C) Pendant: (Assumes no wind chill factor; for detailed test conditions, contact Pelco) Maximum: 140 ° F (60 ° C) absolute maximum 122 ° F (50 ° C) sustained maximum Minimum -15 ° F (-9.4 ° C ...

  • Pelco C2434M - page 16

    16 Pelco Manual C2434M (7/01) REVISION HISTOR Y Manual # Date Comments C2434M 7/01 Original version. P elco, the P elco logo, Camclosure , Esprit, Genex, Legacy , and Spectra are registered trademarks of P elco. © Copyright 2001, Pelc o. Endura and ExSite are trademarks of P elco. All rights reser v ed. PRODUCT WARRANTY AND RETURN INFORMA TION WAR ...

メーカー Pelco カテゴリー Saw

Pelco C2434Mのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- C2434Mの取扱説明書
- Pelcoの製品カード
- パンフレット
- またはPelco C2434Mの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pelco C2434Mの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pelco C2434Mの取り付け説明書、サービスマニュアル、簡易説明書、またはPelco C2434Mのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pelco C2434Mの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pelco C2434Mデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPelco C2434Mを使用するのを助ける技術的文書のことです。説明書は通常、全てのPelco C2434Mユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pelcoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pelco C2434Mの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPelco C2434Mの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pelco C2434Mに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pelco C2434Mデバイスの基本機能を使うにあたってのヒント。 Pelco C2434Mのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pelco C2434Mに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPelco C2434Mのメーカー/サービスへの連絡先に関する情報。

Pelco C2434Mについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPelco C2434Mの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPelco C2434Mで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)