Harbor Freight Tools 34202の取扱説明書

14ページ 0.65 mb
ダウンロード

ページに移動 of 14

Summary
  • Harbor Freight Tools 34202 - page 1

    40 LB. PRESSURIZED SANDBL ASTER ASSEMBL Y and OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd. / Camarillo, CA 9301 1 Copyright © 1997 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight T ools. For t ...

  • Harbor Freight Tools 34202 - page 2

    SPECIFICA TIONS Capacity: 40 lbs. Working Pressure 60-125 PSI Delivery Rate 6-25 CFM Overall Dimensions 33.5" x 18.75" x 13" Weight: 57 lbs. SA VE THIS MANUAL Y ou will need the manual for the safety warnings and cautions, assembly instructions, operating procedures, maintenance procedures, trouble shooting, parts list, and diagram. ...

  • Harbor Freight Tools 34202 - page 3

    9. DO NOT ABUSE THE POWER CORD. Do not yank compressor ’s cord to disconnect it from the receptacle. Do not carry tools by the cord. 10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or across running machines. 11 . MAINT AIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow i ...

  • Harbor Freight Tools 34202 - page 4

    22. MAINT AIN CORRECT AIR PRESSURE WHENEVER WORKING . Do not allow pressure to exceed 125 PSI. If the safety valve does not release excess air pressure, stop all work and use the air compressor to release pressure in the tank. Do not attempt any repairs to the Sandblaster until its gauge reads “0”. AIR/SAND SUPPL Y REQUIREMENTS Hose Hose Nozzle ...

  • Harbor Freight Tools 34202 - page 5

    ASSEMBL Y NOTE: Use T eflon® Pipe T ape on all threaded joints. Make sure all joints are securely tighten. Intake Manifold Refer to Figure 1. S tep1: Get out the INT AKE MANIFOLD (#14), PRESSURE GAUGE (#15), BRASS THROTTLING V AL VE (#18A), 3/8" 1/4" NIPPLE CONNECTOR (#20), and JOINT PIPE (#13). S tep2: Attach the PRESSURE GAUGE to the t ...

  • Harbor Freight Tools 34202 - page 6

    Water Trap Refer to Figure 2. Figure 2 — Water Trap Assembly S tep1: Get out the WA TER TRAP (#17), two 3/8" NIPPLE CONNECTORS (#16), the BRASS AIR SUPPL Y V AL VE (#18), and the MALE/FEMALE ADAPTER (#19). S tep2: A tt ach the 3/8" NIPPLE CONNECTORS to either side of the W A TER TRAP . S tep3: On the top of the WA TER TRAP is an arrow . ...

  • Harbor Freight Tools 34202 - page 7

    Nozzle Shut Off V alve Refer to Figure 4. S tep1: Get out the HOSE ADAPTER (#25), the STEEL SHUT OFF V AL VE (#18C), a NIPPLE CONNECTOR (#16), the GASKET (#26), the desired size NOZZLE (#27A-D), and the NOZZLE CAP NUT (#28). S tep2: Put the front of the NOZZLE through the NOZZLE CAP NUT . S tep3: Attach the NOZZLE CAP NUT to the NIPPLE CONNECTOR wi ...

  • Harbor Freight Tools 34202 - page 8

    S tep5: At t ach the HOSE ADAPTER to the other end of the STEEL SHUT OFF V AL VE. Sand Control V alve/ Nozzle Shut Off V alve Refer to Figure 5. Sand Con trol V alve Assem bly Sand Hose Nozzle Shut O ff V alve Asse m bly Hose Clamp (# 23) Figure 5 — Sand Control V alve / Shut Off V alve Assembly S tep1: Get out the Sand Control V alve & Nozzl ...

  • Harbor Freight Tools 34202 - page 9

    T op Assembly Refer to Figure 6. T ank (# 1) Ni pple Connector (# 16) Ni pple Connector (# 16) Air Hos e (# 21) Gasket (# 1 1) Air Ca p (# 12) Joint P ipe (# 13) Figure 6 — T op Assembly S tep1: Get the Int ake V alve Assembly , the W ater Trap Assembly , the T ank Assembly , the T ANK CAP (#12), the O-RING (#1 1), and the AIR HOSE (#21). S tep2: ...

  • Harbor Freight Tools 34202 - page 10

    Handle Bars Refer to Figure 7. Handl e Grip (# 7) Handl e B ar (# 6) Scre w (# 8) W asher (# 31) Nut (# 9) Figure 7 — Handle Bar Assembly S tep1: Get out the two HANDLE BARS (#6), the two HANDLE GRIPS (#5), the four SCREWS (#8), four NUTS (#9), and four W ASHERS (#31). S tep2: Sl ide the HANDLE GRIPS onto the HANDLE BARS. S tep3: A tt ach both HA ...

  • Harbor Freight Tools 34202 - page 11

    Wheels and Foot See Figure 8. 5 3 2 4 3 3 2 Figure 8 - Wheel and Foot Attachment S tep 1: Get out the two WHEELS (#2), the three COTTER PINS (#3), the FOOT (#4) and the AXLE (#5). S tep 2: Attach the FOOT to the T ANK (#1) using one of the COTTER PINS. S tep 3: Attach one of the WHEELS to the AXLE using one of the COTTER PINS. S tep 4: Slide the AX ...

  • Harbor Freight Tools 34202 - page 12

    OPERA TIONS Loading Abrasives S tep 1: Check to insure the abrasives are dry and clean so that they do not clog the unit. S tep 2: Close the AIR SUPPL Y V AL VE (#18) by turning it to the horizontal position. S tep 3: Open the NOZZLE SHUT OFF V AL VE (#18C) by turning it to the vertical position. S tep 4: Make sure the PRESSURE GAUGE (#15) reads ? ...

  • Harbor Freight Tools 34202 - page 13

    Item# Description Q ty Item# Description Q ty 1 T a nk 1 18B 3/8" S teel Sand Control V alve 1 2 Wheel 2 18C 3/8" S teel Shut Off V alve 1 3 Cotter Pin 3 1 9 Male/Female Adapter 1 4 Foot 1 20 3/8" 1/4" Nipple Connector 1 5 Axle 1 21 Air Hose 1 6 * Handle Bar 2 22 Sand Outlet Manifold 1 7 Handle Grip 2 23 Hose Clamp 2 8 Pan Screw ...

  • Harbor Freight Tools 34202 - page 14

    19 16 16 17 15 14 18A 20 18 13 7 8 9 3 5 21 14 2 1 24 23 28 27A-D 26 16 18C 25 16 18B 16 22 23 31 12 11 10 6 3 P ARTS DRA WING Page #14 -- SKU 34202 ...

メーカー Harbor Freight Tools カテゴリー Sander

Harbor Freight Tools 34202のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 34202の取扱説明書
- Harbor Freight Toolsの製品カード
- パンフレット
- またはHarbor Freight Tools 34202の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Harbor Freight Tools 34202の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Harbor Freight Tools 34202の取り付け説明書、サービスマニュアル、簡易説明書、またはHarbor Freight Tools 34202のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Harbor Freight Tools 34202の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Harbor Freight Tools 34202デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHarbor Freight Tools 34202を使用するのを助ける技術的文書のことです。説明書は通常、全てのHarbor Freight Tools 34202ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Harbor Freight Toolsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Harbor Freight Tools 34202の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHarbor Freight Tools 34202の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Harbor Freight Tools 34202に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Harbor Freight Tools 34202デバイスの基本機能を使うにあたってのヒント。 Harbor Freight Tools 34202のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Harbor Freight Tools 34202に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHarbor Freight Tools 34202のメーカー/サービスへの連絡先に関する情報。

Harbor Freight Tools 34202についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHarbor Freight Tools 34202の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHarbor Freight Tools 34202で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)