RedMax G3100Tの取扱説明書

28ページ 0.69 mb
ダウンロード

ページに移動 of 28

Summary
  • RedMax G3100T - page 1

    OWNER / OPERA T OR MANUAL CHAINSA WS T2054-93110 (606) The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit. W ARNING APPLICABLE SERIAL NUMBERS ...

  • RedMax G3100T - page 2

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • RedMax G3100T - page 3

    2. Specifications ■ G3100T Power unit : Displacement ···················································································· 1.9 (30.1) cu-in (cm 3 ) Fuel ················································ ...

  • RedMax G3100T - page 4

     4  3. Symbols on the machine MADE IN IT AL Y IMPORT ANT ENGINE INFORMA TION THIS ENGINE CONFORMS TO US EP A PH1 FOR SMALL OFF-RO AD ENGINES. ENGINE F AMIL Y : 3E8XS.0304TH ENGINE DISPLACEMENT : 30.1cm 3 MANUF ACTURED: REFER TO O WNER'S MANUMAL FOR MAINTE- NANCE SPECIFICA TIONS AND ADJUSTMENTS. W ARNING! THIS SAW IS FOR TRAINED TREE SERV ...

  • RedMax G3100T - page 5

    4. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing and head protection devices. 3. Always use caution when handling fuel. Wipe up a ...

  • RedMax G3100T - page 6

     6  4. For safe operation 16. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 17. Do not operate a chain saw in a tree unless specially trained to do so. 18. Guard against kickback. Kickback is the upward motion of the guide b ...

  • RedMax G3100T - page 7

    A standard saw unit package contains the items as shown. (SE1) Open the box and install the guide bar and the saw chain to the power unit as follows. The saw chain has very sharp edges. Use thick, protective gloves to avoid injury. 1. Loosen a nut and remove the chain cover. 2. Mount the guide bar and fit the saw chain around the bar and the drive ...

  • RedMax G3100T - page 8

     8  6. Fuel and chain oil • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine. • The RedMax engines are lubri ...

  • RedMax G3100T - page 9

    6. Fuel and Chain oil again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture. 5. Put a clear indication o ...

  • RedMax G3100T - page 10

     10  ■ FUELING THE UNIT (OP1) 1. Remove the fuel tank cap and pour fuel into the tank up to 80% of full capacity. 2. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. 3. Remove the oil tank cap and pour chain oil into the tank. Fasten the cap securely. 1. Select bare ground for fueling. 2. Move at least 10 feet (3 ...

  • RedMax G3100T - page 11

    7. Operation 5. While holding the saw unit securely on the ground, pull the starter rope vigorously. (OP5) Do not start the engine while hanging the chain saw with a hand. The saw chain may touch your body. It's very dangerous. 6. When engine has ignited first, push in the choke knob and pull the rope again to start the engine. 7. Allow the en ...

  • RedMax G3100T - page 12

    ■ ADJUSTING CARBURETOR (OP8) The carburetor on your unit has been factory adjusted, but may require fine tuning due to change in operating conditions. Before adjusting the carburetor, make sure that provided are clean air/fuel filters and fresh, properly mixed fuel. When adjusting, take the following steps: Be sure to adjust the carburetor with t ...

  • RedMax G3100T - page 13

    7. Operation •W hen the brake worked, immediately release the throttle lever and slow down the engine speed. Running the engine at high speed while braking the saw chain can cause clutch failures. • Before starting the day's job, check the condition of the brake system as follows: 1) Start the engine and grasp the handles securely with bot ...

  • RedMax G3100T - page 14

    • Before proceeding to your job, read “For Safe Operation” section. It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full throttle. • Racing the engine with the chain seized in a ...

  • RedMax G3100T - page 15

    should stop immediately with the engine at full speed. If the chain is slow to stop or does not stop then replace the brake band and clutch drum before use. • It is extremely important that the chain brake be checked for proper operation before each use and that the chain be sharp in order to maintain the kickback safety level of this saw. Remova ...

  • RedMax G3100T - page 16

    of bending direction to prevent the guide bar from being caught in the cutaway. ● Cutting an unpillowed log Saw down halfway, then roll the log over and cut from the opposite side. (SA3) ● Cutting a pillowed log In the area A in the picture right above, saw up from the bottom one-third and finish by sawing down from the top. In the area B, saw ...

  • RedMax G3100T - page 17

     17  9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. Make sure to stop the engine before inspecting and/or servicing the unit. ■ DAILY MAINTENANCE SAW CHAIN It is one of the essential factors for smooth and safe operatio ...

  • RedMax G3100T - page 18

     18  9. Maintenance GUIDE BAR 1. Remove sawdust in the bar groove and the oiling port. (MA5) 2. Grease the nose sprocket from the feeding port on the tip of the guide bar. (MA6) 3. Periodically turn over the guide bar when mounting it to the unit, in order to prevent partial wear. This saw is equipped with one of the following low kickback ba ...

  • RedMax G3100T - page 19

    anything wrong be found, make sure to have it repaired before next usage. ■ MONTHLY MAINTENANCE FUEL FILTER When the engine runs short of fuel supply, check the fuel filter for blockage. (MA9) OIL STRAINER Drain the oil tank and remove the oil strainer located near the spark plug. Check the condition and clean if necessary. (MA10) SPARK PLUG Star ...

  • RedMax G3100T - page 20

     20  SPARK ARRESTER RedMax engines are equipped with a spark arresting screen at the exhaust port. Periodically check and keep it in good condition. In the State of California it is required by law (Section 4442 of the California Public Resources Code) to have a spark arrester when a gas powered tool is used in any forest covered, brush cover ...

  • RedMax G3100T - page 21

     21  1 1. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model ...

  • RedMax G3100T - page 22

     22  1 1. Parts list Fig.1 POWER UNIT G3100T (S/N 0723010001 and up) G3100T ...

  • RedMax G3100T - page 23

     23  Fig.1 POWER UNIT (S/N 0723010001 and up) G3100T 1 T2050-12110 CYLINDER 1 2 T2050-21110 CRANKCASE 1 3 01252-30530 BOLT 4 4 2870-41111 PISTON 1 5 3319-41210 RING 1 6 3304-41310 PIN 1 7 3310-41320 SNAP RING 2 8 3310-41410 BEARING 1 9 1650-41510 WASHER 2 10 2870-42002 CRANKSHAFT COMP 1 11 06030-06201 BEARING 2 12 2630-43150 OIL SEAL 1 13 040 ...

  • RedMax G3100T - page 24

     24  1 1. Parts list Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 0723010001 and up) G3100T ...

  • RedMax G3100T - page 25

     25  Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 0723010001 and up) G3100T Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 T2054-81000 CARBURETOR ASS'Y 2 T2052-81120 • PUMP COVER 1 3 3310-81130 • SCREW 1 4 3310-81280 • COVER 1 5 1480-81420 • PLUG 1 6 3350-81380 • SPR ...

  • RedMax G3100T - page 26

    THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TO EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND GARDEN EQUIPMENT ENGINE. IN CALIFORNIA, NEW UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES MUST BE DESIGNED, BUILT AND EQUIPPED TO MEET THE STATE'S STRINGENT ANTI-SMOG STANDARDS. KOMATSU ZENOAH Co ...

  • RedMax G3100T - page 27

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY, RedMax / KOMATSU ZENOAH AMERICA, INC., THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED PARTS ARE: THE CARBURETOR ASS ...

  • RedMax G3100T - page 28

    Pièces en rapport avec les émissions de gaz d'échappement : RedMax / KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage dé ...

メーカー RedMax カテゴリー Chainsaw

RedMax G3100Tのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- G3100Tの取扱説明書
- RedMaxの製品カード
- パンフレット
- またはRedMax G3100Tの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、RedMax G3100Tの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、RedMax G3100Tの取り付け説明書、サービスマニュアル、簡易説明書、またはRedMax G3100Tのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、RedMax G3100Tの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

RedMax G3100Tデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRedMax G3100Tを使用するのを助ける技術的文書のことです。説明書は通常、全てのRedMax G3100Tユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

RedMaxの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. RedMax G3100Tの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRedMax G3100Tの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。RedMax G3100Tに関してこのドキュメントで見つけることができる全てのヒントの目次
3. RedMax G3100Tデバイスの基本機能を使うにあたってのヒント。 RedMax G3100Tのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。RedMax G3100Tに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRedMax G3100Tのメーカー/サービスへの連絡先に関する情報。

RedMax G3100Tについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもRedMax G3100Tの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRedMax G3100Tで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)