Milwaukee MW600の取扱説明書

12ページ 0.1 mb
ダウンロード

ページに移動 of 12

Summary
  • Milwaukee MW600 - page 1

    Milwa uk ee USER MANUAL PORTABLE DISSOLVED OXYGEN METER MODEL: MW600 Smart DO Meter ...

  • Milwaukee MW600 - page 2

    PROBE PREPARATION: The meter is supplied with a 9V battery. Slide off the battery compartment cover on the back of the meter. Install the battery into the battery clip connector while observing polarity. D.O. probes are shipped dry. Assemble the probe and prepare it for use, connect it to the meter and proceed as follows. 1. Remove the red and blac ...

  • Milwaukee MW600 - page 3

    PROBE POLARIZATION: • A dissolved oxygen probe must be polarized to function properly. • To polarize the probe, the fully assambled probe must be connected to the meter and the meter must be on. • During polarization (and during measurement), approximately 800 mV is applied to the cathode and anode inside the membrane and a chemical reaction ...

  • Milwaukee MW600 - page 4

    Zero Calibration: • Dip the probe into MA9070 zero oxygen solution and stir gently for 2-3 minutes. • Wait for the probe to reach it’s lowest stable reading. • Adjust the zero D.O. calibration trimmer (located on the front panel) until the display reads "0.0". Slope Calibration: It is suggested to perform the slope calibration in ...

  • Milwaukee MW600 - page 5

    TAKING MEASUREMENTS: Verify the probe is polarized and the probe and meter have been calibrated. Remove the protective cap from probe. Immerse the tip of the probe in the sample to be tested. For accurate dissolved oxygen measurements a minimum water movement of 0.3 m/sec is required. This is to ensure that the oxygen-depleted membrane surface is c ...

  • Milwaukee MW600 - page 6

    5 °C 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 0 m 14.6 13.8 13.1 12.4 11.8 11.3 10.8 10.3 9.9 9.5 9.1 8.7 8.4 8.1 7.8 7.5 7.3 7.1 6.8 6.6 6.4 300 m 14.1 13.3 12.7 12.0 11.4 10.9 10.4 9.9 9.7 9.2 8.8 8.4 8.1 7.8 7.5 7.2 7.1 6.9 6.6 6.4 6.2 600 m 13.6 12.9 12.2 11.6 11.0 10.5 10.1 9.6 9.2 8.7 8.5 8.1 7.8 7.5 7.3 7.0 6.8 6.6 6.3 6.2 ...

  • Milwaukee MW600 - page 7

    6 SALINITY COMPENSATION: The t able below illustrates the change in the solubility of oxygen in air saturated water as a result of chloride concentration or salinity . The t able can also be used to correct the displayed measurement. If you are making measurement s in salt water and know the chloride concentration (or salinity), you can multiply yo ...

  • Milwaukee MW600 - page 8

    7 PROBE & MEMBRANE MAINTENANCE: The D.O. probe body is made of reinforced plastic for maximum durability. A thermistor temperature sensor provides temperature measurements of the tested sample. It is always recommended to keep the protective cap on the probe when not in use, to protect the membrane against damage and dirt. To replace the membra ...

  • Milwaukee MW600 - page 9

    The Platinum cathode should always be bright and untarnished. If it is tarnished or stained, due to contact with certain gases or a damaged membrane cap, the cathode should be cleaned. You can use a clean lint-free cardboard or cloth. Rub the cathode very gently side to side 4-5 times. This will be enough to polish and remove any stains without dam ...

  • Milwaukee MW600 - page 10

    BATTERY REPLACEMENT: When the battery becomes weak the meter will display the low battery indicator " ". When this appears, only a few hours of battery life remain. A low battery will result in unreliable measurements. Prompt battery replacement is required. Battery replacement must take place in a non-hazardous area using an alkaline 9V ...

  • Milwaukee MW600 - page 11

    SPECIFICATIONS: MW600 RANGE 0.0 to 19.9 mg/L RESOLUTION 0.1 mg/L ACCURACY (@25°C) ±1.5% Full Scale TEMPERATURE Automatic from 0 to 30°C COMPENSATION CALIBRATION Manual on 2 points (zero and slope) LCD 3½ digits with symbols PROBE MA840 (included) ENVIRONMENT 0 to 50°C, 95% RH max. BATTERY TYPE 9V alkaline (included) BATTERY LIFE approximately ...

  • Milwaukee MW600 - page 12

    ISTMW600 01/10 Milwa uk ee Authorized Dealer: ...

メーカー Milwaukee カテゴリー Marine Instruments

Milwaukee MW600のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MW600の取扱説明書
- Milwaukeeの製品カード
- パンフレット
- またはMilwaukee MW600の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Milwaukee MW600の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Milwaukee MW600の取り付け説明書、サービスマニュアル、簡易説明書、またはMilwaukee MW600のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Milwaukee MW600の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Milwaukee MW600デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMilwaukee MW600を使用するのを助ける技術的文書のことです。説明書は通常、全てのMilwaukee MW600ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Milwaukeeの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Milwaukee MW600の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMilwaukee MW600の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Milwaukee MW600に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Milwaukee MW600デバイスの基本機能を使うにあたってのヒント。 Milwaukee MW600のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Milwaukee MW600に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMilwaukee MW600のメーカー/サービスへの連絡先に関する情報。

Milwaukee MW600についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMilwaukee MW600の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMilwaukee MW600で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)