Cabletron Systems 9000の取扱説明書

26ページ 0.23 mb
ダウンロード

ページに移動 of 26

Summary
  • Cabletron Systems 9000 - page 1

    9031125-03 SmartSwitch 9000 9C114 and 9C714 Chassis Installation Guide ...

  • Cabletron Systems 9000 - page 2

    ...

  • Cabletron Systems 9000 - page 3

    i Notice Notice Cabletron Systems r eserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletr on Systems to determine whether any such changes have been made. The hardwar e, firmware, or softwar e described in this manual is subject to ...

  • Cabletron Systems 9000 - page 4

    Notice ii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may cause undesir ed operation. NOTE: This equipment has been tested and found to c ...

  • Cabletron Systems 9000 - page 5

    iii Notice Dec laration of Conf ormity Addendum Application of Council Directive(s): 89/336/EEC 73/23/EEC Manufacturer ’s Name: Cabletron Systems, Inc. Manufacturer ’s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Repr esentative Name: Mr. J. Solari European Repr esentative Addr ess: Cabletron Systems Limited Nexus House, ...

  • Cabletron Systems 9000 - page 6

    Notice iv ...

  • Cabletron Systems 9000 - page 7

    v Contents Chapter 1 Installing the 9Cx14 Chassis The SmartSwitch 9000 .................................................................................................. 1-1 Features ................................................................................................................... 1-1 Multiple T echnology Support .................. ...

  • Cabletron Systems 9000 - page 8

    Contents vi ...

  • Cabletron Systems 9000 - page 9

    1-1 Chapter 1 Installing the 9Cx14 Chassis This document contains information necessary to install the SmartSwitch 9000 9C1 14 and 9C714 chassis. It is designed for the initial installation only . For detailed operational information on the various SmartSwitch 9000 components, refer to the following manuals: SmartSwitch 9000 9C300-1 Environmental M ...

  • Cabletron Systems 9000 - page 10

    Installing the 9Cx14 Chassis 1-2 Redundant P ower Supply Modules The 9C1 14 and 9C714 support the installation of two power supplies for power supply redundancy and load sharing. If a 9C500 Power Box is used, up to six power supplies may be installed. 9C300-1 En vironmental Module The 9C300-1 Environmental Module pr ovides out-of-band management ca ...

  • Cabletron Systems 9000 - page 11

    1-3 Installing the 9Cx14 Chassis The descriptions of the seven backplane buses are as follows: System Management Bus 1 The System Management Bus 1, abbreviated SMB-1, is a management bus devoted solely to transferring management information between the modules in the chassis. It is through the SMB-1 that modules inform each other , and the Environm ...

  • Cabletron Systems 9000 - page 12

    Installing the 9Cx14 Chassis 1-4 The Cell T ransfer Matrix (installed in the 9C714 chassis onl y) The Cell T ransfer Matrix provides a T ime Division Multiplexed (TDM) based mesh of full duplex, high speed (1.6 Gbps) dedicated interconnections capable of carrying standard A TM cell traffic. These interconnections ar e a series of point-to- point l ...

  • Cabletron Systems 9000 - page 13

    1-5 Installing the 9Cx14 Chassis Site Guidelines The following guidelines must be followed to select a suitable site for the SmartSwitch 9000. If not, unsatisfactory network performance may result. The site must have an unrestricted fr ee surface area around the SmartSwitch 9000 chassis, allowing for free movement of air . An open space of at least ...

  • Cabletron Systems 9000 - page 14

    Installing the 9Cx14 Chassis 1-6 Installation Or der Once a suitable site has been chosen, the SmartSwitch 9000 may be installed. The unit may be free standing or rack mounted. It is recommended that the SmartSwitch 9000 installation pr oceed in this order: 1. Mount the chassis to the rack or other secure location. 2. Install the power supply(ies). ...

  • Cabletron Systems 9000 - page 15

    1-7 Installing the 9Cx14 Chassis Rac k Mounting the Chassis The chassis can be mounted in a standard 19-inch equipment rack. If the rack is not secured to the floor , it is r ecommended that the SmartSwitch 9000 be installed in the bottom half of the rack. This will prevent the rack fr om being top heavy . T wo people may be requir ed to lift the ...

  • Cabletron Systems 9000 - page 16

    Installing the 9Cx14 Chassis 1-8 Installing a P ower Suppl y At least one power supply must be installed on the rear of the MMAC-Plus chassis. Additional power supplies can be added to achieve redundancy . A power supply is installed by plugging it into either the left or right power supply connector on the SmartSwitch 9000 chassis, as shown in Fig ...

  • Cabletron Systems 9000 - page 17

    1-9 Installing the 9Cx14 Chassis Figure 1-3. Installing a P ower Suppl y 100-125v-12A 200-250v-6A 50-60 Hz POWER SUPPLY MODULE 9C214-1 100% 50% 0% STA TUS P W R S N B Load Securing Screw Tab Securing Screw Slot on Chassis ...

  • Cabletron Systems 9000 - page 18

    Installing the 9Cx14 Chassis 1-10 Attaching the Electr ostatic Discharge (ESD) Wrist Strap The ESD W rist Strap must be attached before handling the Envir onmental Module or SmartSwitch 9000 Interface Modules. In addition, observe all precautions when handling these modules to pr event damage from ESD. Attach the ESD W rist Strap by following the s ...

  • Cabletron Systems 9000 - page 19

    1-11 Installing the 9Cx14 Chassis Installing the En vironmental Module The Environmental Module is installed in the slot above the module car d cage in the front of the SmartSwitch 9000 chassis, as shown in Figur e 1-5, by following the steps below: 1. Unpack the Environmental Module by car efully removing it from the shipping box and sliding the t ...

  • Cabletron Systems 9000 - page 20

    Installing the 9Cx14 Chassis 1-12 Figure 1-5. Installing the En vironmental Module Installing Smar tSwitch 9000 Interface Modules SmartSwitch 9000 Interface Modules can be installed in any of the 14 slots that are available. T o install Interface Modules, follow the steps below: 1. Remove the blank panel, covering the slot in which the Interface Mo ...

  • Cabletron Systems 9000 - page 21

    1-13 Installing the 9Cx14 Chassis 5. Install the Interface Module in the chassis by sliding it in any available slot and locking down the top and bottom plastic tabs, as shown in Figure 1-6. T ake car e that the Interface Module slides in straight and properly engages the backplane connectors. When installing the Interface Module, ensure that the c ...

  • Cabletron Systems 9000 - page 22

    Installing the 9Cx14 Chassis 1-14 Attaching 9C614 INB T erminator Modules T wo 9C614 INB T erminator Modules must be attached to the rear of the SmartSwitch 9000 chassis when Interface Modules that use the INB are inserted in the front of the chassis. These modules pr ovide proper termination for the Internal Network Bus (INB). The INB T erminator ...

  • Cabletron Systems 9000 - page 23

    1-15 Installing the 9Cx14 Chassis Figure 1-7. Attaching the INB T erminator Modules P owering up the Smar tSwitch 9000 The SmartSwitch 9000 chassis is powered up by following the steps below: 1. Plug one end of the power cord (supplied with the power supply) into the AC power socket on the lower right front corner of the power supply . 2. Plug the ...

  • Cabletron Systems 9000 - page 24

    Installing the 9Cx14 Chassis 1-16 5. Check that all LEDs on the INB T erminator Module ar e green. If the LEDs are any color other than gr een, refer to the INB T erminator Module Installation Guide . 6. Check that the Status and Alarm LEDs on the Environmental Module are green. If the LEDs are not gr een, refer to the Environmental Module User ’ ...

  • Cabletron Systems 9000 - page 25

    1-17 Installing the 9Cx14 Chassis W eight Unit: 19.96 kilograms (44 pounds) Shipping: 24.95 kilograms (55 pounds) 9C714 MMA C-Plus Chassis Dimensions 76.2 H x 48.3 W x 49.3 D centimeters (30 H x 19 W x 19.4 D inches) W eight Unit: 19.96 kilograms (44 pounds) Shipping: 24.95 kilograms (55 pounds) 9C300-1 En vironmental Module Dimensions 12.7 H x 43. ...

  • Cabletron Systems 9000 - page 26

    Installing the 9Cx14 Chassis 1-18 9C614 INB T erminator Module Dimensions 21.59 H x 2.22 W x 14.92 D centimeters (8.5 H x 0.875 W x 5.875 D inches) W eight Unit: 0.45 kilograms (1 pound) Shipping: 0.68 kilograms (1.5 pounds) ...

メーカー Cabletron Systems カテゴリー Network Router

Cabletron Systems 9000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 9000の取扱説明書
- Cabletron Systemsの製品カード
- パンフレット
- またはCabletron Systems 9000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cabletron Systems 9000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cabletron Systems 9000の取り付け説明書、サービスマニュアル、簡易説明書、またはCabletron Systems 9000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cabletron Systems 9000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Cabletron Systems 9000デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCabletron Systems 9000を使用するのを助ける技術的文書のことです。説明書は通常、全てのCabletron Systems 9000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cabletron Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cabletron Systems 9000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCabletron Systems 9000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cabletron Systems 9000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cabletron Systems 9000デバイスの基本機能を使うにあたってのヒント。 Cabletron Systems 9000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cabletron Systems 9000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCabletron Systems 9000のメーカー/サービスへの連絡先に関する情報。

Cabletron Systems 9000についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCabletron Systems 9000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCabletron Systems 9000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)