English dropdown-ico

Manual Cabletron Systems 9000

26 pages 0.23 mb
Download

Go to site of 26

Summary
  • Cabletron Systems 9000 - page 1

    9031125-03 SmartSwitch 9000 9C114 and 9C714 Chassis Installation Guide ...

  • Cabletron Systems 9000 - page 2

    ...

  • Cabletron Systems 9000 - page 3

    i Notice Notice Cabletron Systems r eserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletr on Systems to determine whether any such changes have been made. The hardwar e, firmware, or softwar e described in this manual is subject to ...

  • Cabletron Systems 9000 - page 4

    Notice ii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may cause undesir ed operation. NOTE: This equipment has been tested and found to c ...

  • Cabletron Systems 9000 - page 5

    iii Notice Dec laration of Conf ormity Addendum Application of Council Directive(s): 89/336/EEC 73/23/EEC Manufacturer ’s Name: Cabletron Systems, Inc. Manufacturer ’s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Repr esentative Name: Mr. J. Solari European Repr esentative Addr ess: Cabletron Systems Limited Nexus House, ...

  • Cabletron Systems 9000 - page 6

    Notice iv ...

  • Cabletron Systems 9000 - page 7

    v Contents Chapter 1 Installing the 9Cx14 Chassis The SmartSwitch 9000 .................................................................................................. 1-1 Features ................................................................................................................... 1-1 Multiple T echnology Support .................. ...

  • Cabletron Systems 9000 - page 8

    Contents vi ...

  • Cabletron Systems 9000 - page 9

    1-1 Chapter 1 Installing the 9Cx14 Chassis This document contains information necessary to install the SmartSwitch 9000 9C1 14 and 9C714 chassis. It is designed for the initial installation only . For detailed operational information on the various SmartSwitch 9000 components, refer to the following manuals: SmartSwitch 9000 9C300-1 Environmental M ...

  • Cabletron Systems 9000 - page 10

    Installing the 9Cx14 Chassis 1-2 Redundant P ower Supply Modules The 9C1 14 and 9C714 support the installation of two power supplies for power supply redundancy and load sharing. If a 9C500 Power Box is used, up to six power supplies may be installed. 9C300-1 En vironmental Module The 9C300-1 Environmental Module pr ovides out-of-band management ca ...

  • Cabletron Systems 9000 - page 11

    1-3 Installing the 9Cx14 Chassis The descriptions of the seven backplane buses are as follows: System Management Bus 1 The System Management Bus 1, abbreviated SMB-1, is a management bus devoted solely to transferring management information between the modules in the chassis. It is through the SMB-1 that modules inform each other , and the Environm ...

  • Cabletron Systems 9000 - page 12

    Installing the 9Cx14 Chassis 1-4 The Cell T ransfer Matrix (installed in the 9C714 chassis onl y) The Cell T ransfer Matrix provides a T ime Division Multiplexed (TDM) based mesh of full duplex, high speed (1.6 Gbps) dedicated interconnections capable of carrying standard A TM cell traffic. These interconnections ar e a series of point-to- point l ...

  • Cabletron Systems 9000 - page 13

    1-5 Installing the 9Cx14 Chassis Site Guidelines The following guidelines must be followed to select a suitable site for the SmartSwitch 9000. If not, unsatisfactory network performance may result. The site must have an unrestricted fr ee surface area around the SmartSwitch 9000 chassis, allowing for free movement of air . An open space of at least ...

  • Cabletron Systems 9000 - page 14

    Installing the 9Cx14 Chassis 1-6 Installation Or der Once a suitable site has been chosen, the SmartSwitch 9000 may be installed. The unit may be free standing or rack mounted. It is recommended that the SmartSwitch 9000 installation pr oceed in this order: 1. Mount the chassis to the rack or other secure location. 2. Install the power supply(ies). ...

  • Cabletron Systems 9000 - page 15

    1-7 Installing the 9Cx14 Chassis Rac k Mounting the Chassis The chassis can be mounted in a standard 19-inch equipment rack. If the rack is not secured to the floor , it is r ecommended that the SmartSwitch 9000 be installed in the bottom half of the rack. This will prevent the rack fr om being top heavy . T wo people may be requir ed to lift the ...

  • Cabletron Systems 9000 - page 16

    Installing the 9Cx14 Chassis 1-8 Installing a P ower Suppl y At least one power supply must be installed on the rear of the MMAC-Plus chassis. Additional power supplies can be added to achieve redundancy . A power supply is installed by plugging it into either the left or right power supply connector on the SmartSwitch 9000 chassis, as shown in Fig ...

  • Cabletron Systems 9000 - page 17

    1-9 Installing the 9Cx14 Chassis Figure 1-3. Installing a P ower Suppl y 100-125v-12A 200-250v-6A 50-60 Hz POWER SUPPLY MODULE 9C214-1 100% 50% 0% STA TUS P W R S N B Load Securing Screw Tab Securing Screw Slot on Chassis ...

  • Cabletron Systems 9000 - page 18

    Installing the 9Cx14 Chassis 1-10 Attaching the Electr ostatic Discharge (ESD) Wrist Strap The ESD W rist Strap must be attached before handling the Envir onmental Module or SmartSwitch 9000 Interface Modules. In addition, observe all precautions when handling these modules to pr event damage from ESD. Attach the ESD W rist Strap by following the s ...

  • Cabletron Systems 9000 - page 19

    1-11 Installing the 9Cx14 Chassis Installing the En vironmental Module The Environmental Module is installed in the slot above the module car d cage in the front of the SmartSwitch 9000 chassis, as shown in Figur e 1-5, by following the steps below: 1. Unpack the Environmental Module by car efully removing it from the shipping box and sliding the t ...

  • Cabletron Systems 9000 - page 20

    Installing the 9Cx14 Chassis 1-12 Figure 1-5. Installing the En vironmental Module Installing Smar tSwitch 9000 Interface Modules SmartSwitch 9000 Interface Modules can be installed in any of the 14 slots that are available. T o install Interface Modules, follow the steps below: 1. Remove the blank panel, covering the slot in which the Interface Mo ...

  • Cabletron Systems 9000 - page 21

    1-13 Installing the 9Cx14 Chassis 5. Install the Interface Module in the chassis by sliding it in any available slot and locking down the top and bottom plastic tabs, as shown in Figure 1-6. T ake car e that the Interface Module slides in straight and properly engages the backplane connectors. When installing the Interface Module, ensure that the c ...

  • Cabletron Systems 9000 - page 22

    Installing the 9Cx14 Chassis 1-14 Attaching 9C614 INB T erminator Modules T wo 9C614 INB T erminator Modules must be attached to the rear of the SmartSwitch 9000 chassis when Interface Modules that use the INB are inserted in the front of the chassis. These modules pr ovide proper termination for the Internal Network Bus (INB). The INB T erminator ...

  • Cabletron Systems 9000 - page 23

    1-15 Installing the 9Cx14 Chassis Figure 1-7. Attaching the INB T erminator Modules P owering up the Smar tSwitch 9000 The SmartSwitch 9000 chassis is powered up by following the steps below: 1. Plug one end of the power cord (supplied with the power supply) into the AC power socket on the lower right front corner of the power supply . 2. Plug the ...

  • Cabletron Systems 9000 - page 24

    Installing the 9Cx14 Chassis 1-16 5. Check that all LEDs on the INB T erminator Module ar e green. If the LEDs are any color other than gr een, refer to the INB T erminator Module Installation Guide . 6. Check that the Status and Alarm LEDs on the Environmental Module are green. If the LEDs are not gr een, refer to the Environmental Module User ’ ...

  • Cabletron Systems 9000 - page 25

    1-17 Installing the 9Cx14 Chassis W eight Unit: 19.96 kilograms (44 pounds) Shipping: 24.95 kilograms (55 pounds) 9C714 MMA C-Plus Chassis Dimensions 76.2 H x 48.3 W x 49.3 D centimeters (30 H x 19 W x 19.4 D inches) W eight Unit: 19.96 kilograms (44 pounds) Shipping: 24.95 kilograms (55 pounds) 9C300-1 En vironmental Module Dimensions 12.7 H x 43. ...

  • Cabletron Systems 9000 - page 26

    Installing the 9Cx14 Chassis 1-18 9C614 INB T erminator Module Dimensions 21.59 H x 2.22 W x 14.92 D centimeters (8.5 H x 0.875 W x 5.875 D inches) W eight Unit: 0.45 kilograms (1 pound) Shipping: 0.68 kilograms (1.5 pounds) ...

Manufacturer Cabletron Systems Category Network Router

Documents that we receive from a manufacturer of a Cabletron Systems 9000 can be divided into several groups. They are, among others:
- Cabletron Systems technical drawings
- 9000 manuals
- Cabletron Systems product data sheets
- information booklets
- or energy labels Cabletron Systems 9000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cabletron Systems 9000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cabletron Systems 9000, service manual, brief instructions and user manuals Cabletron Systems 9000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cabletron Systems 9000.

Similar manuals

A complete manual for the device Cabletron Systems 9000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cabletron Systems 9000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cabletron Systems 9000.

A complete Cabletron Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cabletron Systems 9000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cabletron Systems 9000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cabletron Systems 9000, that we can find in the current document
3. Tips how to use the basic functions of the device Cabletron Systems 9000 - which should help us in our first steps of using Cabletron Systems 9000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cabletron Systems 9000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cabletron Systems 9000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cabletron Systems 9000?

Use the form below

If you did not solve your problem by using a manual Cabletron Systems 9000, ask a question using the form below. If a user had a similar problem with Cabletron Systems 9000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)