Jonsered LT2218Aの取扱説明書

32ページ 2.23 mb
ダウンロード

ページに移動 of 32

Summary
  • Jonsered LT2218A - page 1

    Operator's Manual L T2218A ...

  • Jonsered LT2218A - page 2

    2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine. • ...

  • Jonsered LT2218A - page 3

    3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off. They may fall off and be seriously injured or ...

  • Jonsered LT2218A - page 4

    4 PRODUCT SPECIFICA TIONS Gasoline Capacity 1.5 Gallons (5,68 L) and type: Unleaded Regular Oil T ype (API-SG-SL): SAE 30 (above 32°F/0°C) SAE 5W -30 (below 32°F/0°C) Oil Capacity: W/Filter: 56 0z. W/O Filter: 48 oz. Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Forward: 5.5 Reverse: 2.4 Charging System: 15 Amps Battery: AMP ...

  • Jonsered LT2218A - page 5

    5 UNAS SEMBLED P ARTS Steering Wheel Steering Wheel (1) W asher Seat (1) Seat Steering Boot Steering Extension Shaft Steering Wheel Adapter K ey(s) Slope Sheet (1) Oil Drain T ube F or Future Use (1) He x Bolt (1) He x Bolt (1) Lock W asher (1) Large Flat W asher Steering Wheel Inser t ...

  • Jonsered LT2218A - page 6

    6 AS SEMBL Y TOOLS REQUIRED FOR AS SEMBL Y A socket wrench set will make assembly easier . Stan dard wrench sizes are listed. (1) 3/4" wrench Pliers (2) 7/16" wrenches Tire pressure gauge (1) 5/16" wrench (1) 1/2" wrench Utility knife When right or left hand is mentioned in this man ual, it means when you are in the operating po ...

  • Jonsered LT2218A - page 7

    7 AS SEMBL Y Fig. 3 BOL T FL A T WASHER SEA T P AN PA D T APE SL OT TA B ADJUSTMENT HANDLE Fig. 4 TO CHECK BA TTERY (See Fig. 4) • Lift seat to raised position. NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BA T ...

  • Jonsered LT2218A - page 8

    8 AS SEMBL Y ✓ CHECKLIST BEFORE YOU OPERA TE Y OUR NEW TRAC TOR, WE WISH TO ASSURE THA T YOU RECEIVE THE BEST PER- FORMANCE AND SA TISF ACTION FROM THIS QUALITY PRODUCT . PLEASE REVIEW THE FOLL OWING CHECKLIST : ✓ All assembly instructions have been com plet ed. ✓ No remaining loose parts in carton. ✓ Battery is properly prepared and charge ...

  • Jonsered LT2218A - page 9

    9 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF FUEL CHOKE MOWER HEIGHT REVERS ...

  • Jonsered LT2218A - page 10

    10 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the safety standards of the American National Stand ...

  • Jonsered LT2218A - page 11

    11 OPERA TION 00155 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while op- erating your tractor or per form ing any adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. Fig. ...

  • Jonsered LT2218A - page 12

    12 Fig. 10 OPERA TION TO ADJUST MOWER CUTTING HEIGHT (See Fig. 10) The position of the attachment lift lever (A) determines the cutting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4". The heights are measured from the ground to the blade tip with the engine not ...

  • Jonsered LT2218A - page 13

    13 OPERA TION TO OPERA TE ON HILLS CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. • Choose the slowest speed before starting up or down hills. • Avoid stopping or changing speed on hills. • If stopping is absolutely necessary , push brake pedal quickly to brake position and engage parki ...

  • Jonsered LT2218A - page 14

    14 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de vel - ...

  • Jonsered LT2218A - page 15

    15 OPERA TION MOWING TIPS • Tire chains cannot be used when the mower hous ing is attached to tractor . • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim ming. • Drive so that clippings ...

  • Jonsered LT2218A - page 16

    16 MAINTENANCE LUBRICA TION CHART 01964 ➀ FRONT WHEEL BEARING ZERK ➀ FRONT WHEEL BEARING ZERK ➁ ENGINE ➀ SPINDLE ZERK ➀ SPINDLE ZERK ➀ GENERAL PURPOSE GREASE ➁ REFER TO MAINTENANCE “ENGINE” SECTION IMPORT ANT : DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HA VE SPECIAL NYLON BEARINGS. VISCOUS L U BRI CANTS WILL A TTRACT DUST AND DI ...

  • Jonsered LT2218A - page 17

    17 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed. (See “TO CHECK BRAKE” in the Ser vice and Ad just ments section of th ...

  • Jonsered LT2218A - page 18

    18 MAINTENANCE TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. T o prevent pos - si ble damage to seals, do not use high pressure water or steam to clean transmission. • Inspect cooling f ...

  • Jonsered LT2218A - page 19

    19 MAINTENANCE CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine dam age from overheating. Clean with a wire brush or compressed air to re move dirt and stubborn dried gum fibers. MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SP ARK PLUGS ...

  • Jonsered LT2218A - page 20

    20 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP ” and remove key . • Make sure the blades and all moving parts have completely stopped. ? ...

  • Jonsered LT2218A - page 21

    21 SERVICE AND ADJUSTMENTS M C D A E F B • A TT ACH FRONT LINK (E) - Work from left side of trac- tor . Insert rod end of link assembly through front hole in tractor front suspension bracket (F). • Insert end of link (E) into hole in front mower bracket (H) and secure with washer and retainer spring (J). E F H J M Fig. 23 Fig. 24 • Install be ...

  • Jonsered LT2218A - page 22

    22 FRONT - TO-BACK ADJUSTMENT (See Figs. 28 & 29) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position. CAUTION: Blades are sharp. Protect your hands with gloves and/or w ...

  • Jonsered LT2218A - page 23

    23 SERVICE AND ADJUSTMENTS TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 30) MOWER DRIVE BEL T REMOV AL • P ark tractor on a level surface. En gage parking brake. • Lower attachment lift lever to its lowest position. • Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface. • Remove belt ...

  • Jonsered LT2218A - page 24

    24 SERVICE AND ADJUSTMENTS Fig. 32 0 0663 RE T AIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONL Y) AXLE COVER TO REMOVE WHEEL FOR REP AIRS (See Fig. 32) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear ...

  • Jonsered LT2218A - page 25

    25 SERVICE AND ADJUSTMENTS Fig. 34 Fig. 35 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. INTERL OCKS AND REL A YS Loose or damaged wiring may cause your tractor to ...

  • Jonsered LT2218A - page 26

    26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure. TRACTOR Remove mower from t ...

  • Jonsered LT2218A - page 27

    27 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air filter . 5. Clean/replace air filter . 6. Dirty fuel filte ...

  • Jonsered LT2218A - page 28

    28 TROUBLESHOOTING POINTS Engine continues to run 1. F aulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutch department. engaged Poor cut - uneven 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade ...

  • Jonsered LT2218A - page 29

    29 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven ...

  • Jonsered LT2218A - page 30

    30 SERVICE NOTES ...

  • Jonsered LT2218A - page 31

    31 SERVICE NOTES ...

  • Jonsered LT2218A - page 32

    532 42 71-56 02.12.09 BAD Printed in the U.S.A. Jonsered Motor AB, S-433 81 P artille, Sweden. ...

メーカー Jonsered カテゴリー Lawn Mower

Jonsered LT2218Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- LT2218Aの取扱説明書
- Jonseredの製品カード
- パンフレット
- またはJonsered LT2218Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Jonsered LT2218Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Jonsered LT2218Aの取り付け説明書、サービスマニュアル、簡易説明書、またはJonsered LT2218Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Jonsered LT2218Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Jonsered LT2218Aデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJonsered LT2218Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのJonsered LT2218Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Jonseredの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Jonsered LT2218Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJonsered LT2218Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Jonsered LT2218Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Jonsered LT2218Aデバイスの基本機能を使うにあたってのヒント。 Jonsered LT2218Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Jonsered LT2218Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJonsered LT2218Aのメーカー/サービスへの連絡先に関する情報。

Jonsered LT2218Aについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJonsered LT2218Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJonsered LT2218Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)