English dropdown-ico

Manual Jonsered LT2218A

32 pages 2.23 mb
Download

Go to site of 32

Summary
  • Jonsered LT2218A - page 1

    Operator's Manual L T2218A ...

  • Jonsered LT2218A - page 2

    2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine. • ...

  • Jonsered LT2218A - page 3

    3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off. They may fall off and be seriously injured or ...

  • Jonsered LT2218A - page 4

    4 PRODUCT SPECIFICA TIONS Gasoline Capacity 1.5 Gallons (5,68 L) and type: Unleaded Regular Oil T ype (API-SG-SL): SAE 30 (above 32°F/0°C) SAE 5W -30 (below 32°F/0°C) Oil Capacity: W/Filter: 56 0z. W/O Filter: 48 oz. Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Forward: 5.5 Reverse: 2.4 Charging System: 15 Amps Battery: AMP ...

  • Jonsered LT2218A - page 5

    5 UNAS SEMBLED P ARTS Steering Wheel Steering Wheel (1) W asher Seat (1) Seat Steering Boot Steering Extension Shaft Steering Wheel Adapter K ey(s) Slope Sheet (1) Oil Drain T ube F or Future Use (1) He x Bolt (1) He x Bolt (1) Lock W asher (1) Large Flat W asher Steering Wheel Inser t ...

  • Jonsered LT2218A - page 6

    6 AS SEMBL Y TOOLS REQUIRED FOR AS SEMBL Y A socket wrench set will make assembly easier . Stan dard wrench sizes are listed. (1) 3/4" wrench Pliers (2) 7/16" wrenches Tire pressure gauge (1) 5/16" wrench (1) 1/2" wrench Utility knife When right or left hand is mentioned in this man ual, it means when you are in the operating po ...

  • Jonsered LT2218A - page 7

    7 AS SEMBL Y Fig. 3 BOL T FL A T WASHER SEA T P AN PA D T APE SL OT TA B ADJUSTMENT HANDLE Fig. 4 TO CHECK BA TTERY (See Fig. 4) • Lift seat to raised position. NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BA T ...

  • Jonsered LT2218A - page 8

    8 AS SEMBL Y ✓ CHECKLIST BEFORE YOU OPERA TE Y OUR NEW TRAC TOR, WE WISH TO ASSURE THA T YOU RECEIVE THE BEST PER- FORMANCE AND SA TISF ACTION FROM THIS QUALITY PRODUCT . PLEASE REVIEW THE FOLL OWING CHECKLIST : ✓ All assembly instructions have been com plet ed. ✓ No remaining loose parts in carton. ✓ Battery is properly prepared and charge ...

  • Jonsered LT2218A - page 9

    9 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF FUEL CHOKE MOWER HEIGHT REVERS ...

  • Jonsered LT2218A - page 10

    10 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the safety standards of the American National Stand ...

  • Jonsered LT2218A - page 11

    11 OPERA TION 00155 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while op- erating your tractor or per form ing any adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. Fig. ...

  • Jonsered LT2218A - page 12

    12 Fig. 10 OPERA TION TO ADJUST MOWER CUTTING HEIGHT (See Fig. 10) The position of the attachment lift lever (A) determines the cutting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4". The heights are measured from the ground to the blade tip with the engine not ...

  • Jonsered LT2218A - page 13

    13 OPERA TION TO OPERA TE ON HILLS CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. • Choose the slowest speed before starting up or down hills. • Avoid stopping or changing speed on hills. • If stopping is absolutely necessary , push brake pedal quickly to brake position and engage parki ...

  • Jonsered LT2218A - page 14

    14 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de vel - ...

  • Jonsered LT2218A - page 15

    15 OPERA TION MOWING TIPS • Tire chains cannot be used when the mower hous ing is attached to tractor . • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim ming. • Drive so that clippings ...

  • Jonsered LT2218A - page 16

    16 MAINTENANCE LUBRICA TION CHART 01964 ➀ FRONT WHEEL BEARING ZERK ➀ FRONT WHEEL BEARING ZERK ➁ ENGINE ➀ SPINDLE ZERK ➀ SPINDLE ZERK ➀ GENERAL PURPOSE GREASE ➁ REFER TO MAINTENANCE “ENGINE” SECTION IMPORT ANT : DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HA VE SPECIAL NYLON BEARINGS. VISCOUS L U BRI CANTS WILL A TTRACT DUST AND DI ...

  • Jonsered LT2218A - page 17

    17 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed. (See “TO CHECK BRAKE” in the Ser vice and Ad just ments section of th ...

  • Jonsered LT2218A - page 18

    18 MAINTENANCE TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. T o prevent pos - si ble damage to seals, do not use high pressure water or steam to clean transmission. • Inspect cooling f ...

  • Jonsered LT2218A - page 19

    19 MAINTENANCE CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine dam age from overheating. Clean with a wire brush or compressed air to re move dirt and stubborn dried gum fibers. MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SP ARK PLUGS ...

  • Jonsered LT2218A - page 20

    20 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP ” and remove key . • Make sure the blades and all moving parts have completely stopped. ? ...

  • Jonsered LT2218A - page 21

    21 SERVICE AND ADJUSTMENTS M C D A E F B • A TT ACH FRONT LINK (E) - Work from left side of trac- tor . Insert rod end of link assembly through front hole in tractor front suspension bracket (F). • Insert end of link (E) into hole in front mower bracket (H) and secure with washer and retainer spring (J). E F H J M Fig. 23 Fig. 24 • Install be ...

  • Jonsered LT2218A - page 22

    22 FRONT - TO-BACK ADJUSTMENT (See Figs. 28 & 29) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position. CAUTION: Blades are sharp. Protect your hands with gloves and/or w ...

  • Jonsered LT2218A - page 23

    23 SERVICE AND ADJUSTMENTS TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 30) MOWER DRIVE BEL T REMOV AL • P ark tractor on a level surface. En gage parking brake. • Lower attachment lift lever to its lowest position. • Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface. • Remove belt ...

  • Jonsered LT2218A - page 24

    24 SERVICE AND ADJUSTMENTS Fig. 32 0 0663 RE T AIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONL Y) AXLE COVER TO REMOVE WHEEL FOR REP AIRS (See Fig. 32) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear ...

  • Jonsered LT2218A - page 25

    25 SERVICE AND ADJUSTMENTS Fig. 34 Fig. 35 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. INTERL OCKS AND REL A YS Loose or damaged wiring may cause your tractor to ...

  • Jonsered LT2218A - page 26

    26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure. TRACTOR Remove mower from t ...

  • Jonsered LT2218A - page 27

    27 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air filter . 5. Clean/replace air filter . 6. Dirty fuel filte ...

  • Jonsered LT2218A - page 28

    28 TROUBLESHOOTING POINTS Engine continues to run 1. F aulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutch department. engaged Poor cut - uneven 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade ...

  • Jonsered LT2218A - page 29

    29 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven ...

  • Jonsered LT2218A - page 30

    30 SERVICE NOTES ...

  • Jonsered LT2218A - page 31

    31 SERVICE NOTES ...

  • Jonsered LT2218A - page 32

    532 42 71-56 02.12.09 BAD Printed in the U.S.A. Jonsered Motor AB, S-433 81 P artille, Sweden. ...

Manufacturer Jonsered Category Lawn Mower

Documents that we receive from a manufacturer of a Jonsered LT2218A can be divided into several groups. They are, among others:
- Jonsered technical drawings
- LT2218A manuals
- Jonsered product data sheets
- information booklets
- or energy labels Jonsered LT2218A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jonsered LT2218A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jonsered LT2218A, service manual, brief instructions and user manuals Jonsered LT2218A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jonsered LT2218A.

Similar manuals

A complete manual for the device Jonsered LT2218A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jonsered LT2218A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jonsered LT2218A.

A complete Jonsered manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jonsered LT2218A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jonsered LT2218A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jonsered LT2218A, that we can find in the current document
3. Tips how to use the basic functions of the device Jonsered LT2218A - which should help us in our first steps of using Jonsered LT2218A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jonsered LT2218A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jonsered LT2218A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jonsered LT2218A?

Use the form below

If you did not solve your problem by using a manual Jonsered LT2218A, ask a question using the form below. If a user had a similar problem with Jonsered LT2218A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)