Frigidaire 2020213A0362の取扱説明書

10ページ 0.49 mb
ダウンロード

ページに移動 of 10

Summary
  • Frigidaire 2020213A0362 - page 1

    ...

  • Frigidaire 2020213A0362 - page 2

    Recommended grounding method: For your personal safety, this appliance must be grounded. This air conditioner includes a power supply cord with a 3-prong grounding plug. T o minimize possible electrical shock hazard: -cord must be plugged into a mating 3-prong grounding-type wall receptacle, -must be grounded in accordance with National Electrical Code (ANSI/NFPA 70- latest version) and -all local codes and ordinances. If a mating 3-prong grounding-type wall receptacle is not available, it is the responsibility of the consumer to have a properly grounded 3-prong wall receptacle installed by a qualified electrician. Electrical Connection Electrical ground is required on this appliance. Prepar ...

  • Frigidaire 2020213A0362 - page 3

    1. Make sure you have all the necessary parts. Installation kit contents: 1. Platform (1) 2. Support brace (1) 3. Adjustment bolt (1) 4. Hex flange nut - 1/4" (1) 5. Track seal (1) 6. Side channel seal (1) 7. Foam seal strip/Sash seal 8. Safety bracket (1) 9-11. Screw - #10 x 2-1/2" flat-head (2), OR Screw - #10 x 1-3/4" pan-head (2), OR Screw - #10 x 1" pan-head (2) 12. Screw - #8 x 3/4" pan head (6) 13. Screw - #8 x 3/4" self-threading (7) 14. Window locking bracket (1) 15. Plastic window panel (1) 16. Side channel (2) 17. Screw - #8 x 3/8" truss head (6) 18. Panel frame/seal assembly (1) NOTE: Use scale below to measure length of your screws. The scale w ...

  • Frigidaire 2020213A0362 - page 4

    Choose a window that allows the cooled air to flow freely and directly into room(s) you wish to cool. Remember, it is difficult to move air around corners. Also, choose a window that is within 6 feet of an electrical outlet. (See Meeting Electrical Requirements/Receptacle wiring needs.) Do not use an extension cord. 3. Choose the proper window location. Installing Unit in a Sliding Window 1. Attach support brace to platform as shown. Use adjustment bolt and hex flange nut to complete assembly. Choose slot and adjustment bolt hole locations that will create a 45 degree angle between platform and support brace. Try assembly in the window to determine if platform will rest properly, and allow p ...

  • Frigidaire 2020213A0362 - page 5

    4. Peel off protective backing from track seal. Apply seal to room side of window track. Center of seal strip should coincide with the line marked in Step 2. The two screw holes drilled in Step 3 should be directly above seal strip in the inner track. 5. Securely attach a siding-protection board to side of house. NOTE: Siding-protection board should be long enough to span 2 wall studs. 6. Place platform assembly, with platform tab against inside of window track, and attach it to window jamb. Use appropriate length screws (Items 9-11 in Preparing For Installation). 7. Adjust platform assembly so that outside edge is 3/16-inch lower than inside edge, as shown right. This ensures proper water d ...

  • Frigidaire 2020213A0362 - page 6

    Slide inner window sash firmly against Cabinet. 10. Clamp plastic window panel between a board and a work table, and cut along cutting line with a fine tooth saw. Remove any burrs with a file. 11. Fasten side channels to the sides of the AC using 3 screws (Item 17) per channel. Start with first screw at top of channel. Make sure hook ends of channels face toward back of unit. 12. Slide plastic window panel into panel frame, with the smooth side to the room. Slide panel frame assembly into side channels of the AC cabinet. Make sure plastic window panel is firmly enclosed on all sides by the retainer grooves. 13. Cut side channel seal into 2 equal lengths. Remove protective backing and apply i ...

  • Frigidaire 2020213A0362 - page 7

    16. Slide inner window sash firmly against side of the cabinet. Make sure not to peel the seal strips from the window track and cabinet side channels. If the panel frame does not fit snugly to the inner window sash, secure the panel frame to the sash with #8x3/4-inch screws, or #8-32x3/4-inch self- threading screws. Use the partially plugged holes in the panel frame. Drill 1/8-inch pilot holes for the screws. 17. Hook the safety bracket over the base of the unit and fasten it to the front of the platform assembly. Use a #8-32x3/4-inch self-threading screw. NOTE: The bracket prevents movement of the air conditioner (either in or out) after completing the installation. 18. Stuff the foam seal ...

  • Frigidaire 2020213A0362 - page 8

    Installing the Unit in a Casement Window NOTE: Open the window the maximum amount to allow for clearance of the cabinet. The crank handle should be removed to allow the platform to be fastened to the jamb. If the window cannot open far enough (more than 15-1/2 inches) for the cabinet to clear the window, remove the window entirely by drilling out the rivets. Bolts can serve as the pivots in the future. T o avoid crank handle and window clearance problems, the unit can be installed in a stationary sash section. However, the horizontal mullion and the 2 glass panels must be removed before installation. 1. Attach support brace to platform as shown. Use the adjustment bolt and hex flange nut to ...

  • Frigidaire 2020213A0362 - page 9

    5. Adjust the platform assembly so that the rear of the air conditioner will be 3/16-inch lower than the front. This ensures proper water drainage from the air conditioner. NOTE: A projection below the base of the air conditioner will require the rear of the platform to be 7/16-inch lower than the front to create the 3/16-inch slant from front to rear. 6. Securely attach a siding-protection board to the side of the house where the platform assembly hit the house. The siding-protection board should be long enough to span 2 wall studs. 7. Measure the height of the window opening from the top of the platform assembly. Subtract 20-5/8 inches. Mark this measurement on the plastic window panel, al ...

  • Frigidaire 2020213A0362 - page 10

    11. Cut side channel seal into 2 equal lengths. Remove the protective backing and apply it to the rear side of the cabinet side channels, starting just below the panel frame assembly. Pinch off excess length so the seal is even with the bottom of the cabinet side channel. 12. To remove front NOTE: DO NOT push or pull air direction louvers. 13. Place the air conditioner in the window opening as shown to the right. It should sit on the platform assembly so that the window panel frame, and the cabinet side channels are against the top and side window jambs. Side channels should overlap side window jambs equally. 14. Drill two 9/64-inch diameter pilot holes in the top window jamb in line with th ...

メーカー Frigidaire カテゴリー Air Conditioner

Frigidaire 2020213A0362のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 2020213A0362の取扱説明書
- Frigidaireの製品カード
- パンフレット
- またはFrigidaire 2020213A0362の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Frigidaire 2020213A0362の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Frigidaire 2020213A0362の取り付け説明書、サービスマニュアル、簡易説明書、またはFrigidaire 2020213A0362のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Frigidaire 2020213A0362の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Frigidaire 2020213A0362デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがFrigidaire 2020213A0362を使用するのを助ける技術的文書のことです。説明書は通常、全てのFrigidaire 2020213A0362ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Frigidaireの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Frigidaire 2020213A0362の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははFrigidaire 2020213A0362の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Frigidaire 2020213A0362に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Frigidaire 2020213A0362デバイスの基本機能を使うにあたってのヒント。 Frigidaire 2020213A0362のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Frigidaire 2020213A0362に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるFrigidaire 2020213A0362のメーカー/サービスへの連絡先に関する情報。

Frigidaire 2020213A0362についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもFrigidaire 2020213A0362の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがFrigidaire 2020213A0362で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)