Wasp Bar Code WPL305の取扱説明書

17ページ 1.98 mb
ダウンロード

ページに移動 of 17

Summary
  • Wasp Bar Code WPL305 - page 1

    WPL305 Thermal Label Printer User’s Guide For Wasp Technologies DT/TT Printer  Copyright Wasp Bar Code Technologies 2004. All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means without the written permission of Wasp Bar Code Technologies. The information contained in this document is subje ...

  • Wasp Bar Code WPL305 - page 2

    1. Introduction ............................................................................................1 2. Getting Started .......................................................................................1 2.1 Unpacking and Inspection .......................................... 1 2.2 Equipment Checklist .................................. ...

  • Wasp Bar Code WPL305 - page 3

    1. Introduction Thank you for purchasing the W305 Thermal Transfer and Direct Thermal Bar Code Printer. Although the printer takes only a small amount of space, it delivers reliable, superior performance. This printer provides both thermal transfer and direct thermal printing at user selectable speed of: 2.0, 3.0, 4.0 or 5.0ips. It accepts roll fee ...

  • Wasp Bar Code WPL305 - page 4

    2.3 Printer Parts Figure 1: Top front view 3. Setup 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface. 2. Make sure the power switch is off. 3. Connect the printer to the computer with the Centronics or USB cable. 4. Plug the power cord into the power supply connector at the rear of the printer, and then plug the power cord ...

  • Wasp Bar Code WPL305 - page 5

    ribbon, please refer to the ribbon calibration procedure to calibrate the ribbon sensor. NOTE: If you are using direct thermal labels you should not load a ribbon. 1. Push down on the ribbon access window to unlock and open the cover. 2. Wasp Ribbons come with the cardboard rewind core already attached to the ribbon for ease of accurate installatio ...

  • Wasp Bar Code WPL305 - page 6

    Make sure both the ribbon access window and the printer top cover are closed when powering up the printer. 3.3 Loading Label Stock 1. Insert a 1” label spindle into the label roll. If your paper core is 1 inch, you can remove the 1.5” core adapters from the centering tab. If the label width is 4 inches wide, the two centering tabs are not requi ...

  • Wasp Bar Code WPL305 - page 7

    Figure 6: Label installation 4. Feed the paper, printing side face up, under the Teflon bar and the paper guide and pass over the platen. 5. Adjust the yellow center-biased paper guides to slightly touch the edges of the label backing. 6. To close the printer top cover, lift the cover to the ultimate open angle then use both hands to close the cove ...

  • Wasp Bar Code WPL305 - page 8

    Figure 7: Top cover support is fixed at position 2 4. To close the cover, lift up the top cover to the ultimate angle then close the top cover gently and it will be kept at a stop position between 1 and 2 for a while. The cover will close automatically after several minutes. If you want to speed the closing, use both hands to gently push down the t ...

  • Wasp Bar Code WPL305 - page 9

    Figure 9: Use both hands to close the top cover 5. Do not force the cover! If you are not sure if top cover is locked at a stop position, please do not push top cover to close it or the top cover will be damaged. Instead, open the top cover as wide as it will go and close the cover again. Use both hands to push top cover to close it. ...

  • Wasp Bar Code WPL305 - page 10

    4. Power on Utilities There are three power-on utilities to set up and test printer hardware. 1. Printer initialization 2. Ribbon sensor calibration 3. Gap or black mark sensor calibration Note: You must run the #2 and #3 utilities after running the #1 to properly set up the printer. 4.1 Initialization Printer initialization is used to clear DRAM a ...

  • Wasp Bar Code WPL305 - page 11

    4.3 Gap/Black Mark Calibration Gap/black mark sensor sensitivity should be calibrated at the following conditions: 1. A brand new printer 2. Change label stock 3. Printer initialization Please follow the steps below to calibrate the sensor. 1. Turn the printer power off. 2. Press and hold the FEED button then turn on the printer. 3. The LED will tu ...

  • Wasp Bar Code WPL305 - page 12

    The printer will enter dump mode after printing the printer configuration. In dump mode, all characters will be printed in 2 columns as in the figure below. Figure 11: Dump mode printout The left side characters are received from your system and the right side data are the corresponding hexadecimal values of the characters. Dump mode allows users t ...

  • Wasp Bar Code WPL305 - page 13

    5. Maintenance 5.1 Cleaning Use one or more of the following supplies that meets your needs: n Cleaning pens n Cleaning swabs n Lint-free cloth Printer Part Method Printer Head n Let the print head to cool for one minute. n Use a cleaning pen to swab the print elements. Platen Roller n Rotate the platen roller and wipe it thoroughly with 70% alcoho ...

  • Wasp Bar Code WPL305 - page 14

    Utilities . 6.2 Print Quality Continuous feeding labels n The printer settings may be wrong. Please do the Initialization and Gap/Black Mark Calibration . No print on the label n Is the label or ribbon loaded correctly? Follow the instructions in Loading the Labels or Loading the Ribbon . n Has the ribbon run out? Follow the instructions in Loading ...

  • Wasp Bar Code WPL305 - page 15

    7. Specifications 7.1 Printer Specifications Item W305 Mechanism Resolution 203 dpi. Max. Print Width 108 mm. Max. Print Length 1000 mm ( 39” ). Ribbon Capacity 300 meter with 1” core. (Max. OD 67 mm) Printing Speed 2, 3, 4 and 5 ips. Peeler function 2, 3 ips Printing Method Direct thermal and thermal transfer printing. Enclosure Structure Dime ...

  • Wasp Bar Code WPL305 - page 16

    Wound Type Outside wound. Width 20mm ~ 112mm (0.78” ~ 4.4”). Length 10mm ~ 1000mm (0.4” ~ 39”). 25.4mm ~ 1000mm (1” ~ 39”).(for peeler and cutter) Thickness 0.06mm ~ 0.19mm. (2.3~7.4 mil), max. 150g/m 2 Roll Diameter 5”. Roll Core Diameter 25.4mm ~ 76.2mm (1” ~ 3”). Gap Height 2mm min. Black Mark Height 2mm min. Black Mark Width 8 ...

  • Wasp Bar Code WPL305 - page 17

    This warranty is limited to repair or replacement at Wasp Technologies’ option, with reasonable promptness after being notified. These provisions do not prolong the original warranty term for any product which has been repaired or replaced by Wasp Technologies. This warranty applies to the original owner and does not extend to any product which h ...

メーカー Wasp Bar Code カテゴリー Printer

Wasp Bar Code WPL305のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WPL305の取扱説明書
- Wasp Bar Codeの製品カード
- パンフレット
- またはWasp Bar Code WPL305の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Wasp Bar Code WPL305の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Wasp Bar Code WPL305の取り付け説明書、サービスマニュアル、簡易説明書、またはWasp Bar Code WPL305のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Wasp Bar Code WPL305の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Wasp Bar Code WPL305デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWasp Bar Code WPL305を使用するのを助ける技術的文書のことです。説明書は通常、全てのWasp Bar Code WPL305ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Wasp Bar Codeの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Wasp Bar Code WPL305の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWasp Bar Code WPL305の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Wasp Bar Code WPL305に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Wasp Bar Code WPL305デバイスの基本機能を使うにあたってのヒント。 Wasp Bar Code WPL305のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Wasp Bar Code WPL305に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWasp Bar Code WPL305のメーカー/サービスへの連絡先に関する情報。

Wasp Bar Code WPL305についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWasp Bar Code WPL305の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWasp Bar Code WPL305で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)