English dropdown-ico

Manual Wasp Bar Code WPL305

17 pages 1.98 mb
Download

Go to site of 17

Summary
  • Wasp Bar Code WPL305 - page 1

    WPL305 Thermal Label Printer User’s Guide For Wasp Technologies DT/TT Printer  Copyright Wasp Bar Code Technologies 2004. All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means without the written permission of Wasp Bar Code Technologies. The information contained in this document is subje ...

  • Wasp Bar Code WPL305 - page 2

    1. Introduction ............................................................................................1 2. Getting Started .......................................................................................1 2.1 Unpacking and Inspection .......................................... 1 2.2 Equipment Checklist .................................. ...

  • Wasp Bar Code WPL305 - page 3

    1. Introduction Thank you for purchasing the W305 Thermal Transfer and Direct Thermal Bar Code Printer. Although the printer takes only a small amount of space, it delivers reliable, superior performance. This printer provides both thermal transfer and direct thermal printing at user selectable speed of: 2.0, 3.0, 4.0 or 5.0ips. It accepts roll fee ...

  • Wasp Bar Code WPL305 - page 4

    2.3 Printer Parts Figure 1: Top front view 3. Setup 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface. 2. Make sure the power switch is off. 3. Connect the printer to the computer with the Centronics or USB cable. 4. Plug the power cord into the power supply connector at the rear of the printer, and then plug the power cord ...

  • Wasp Bar Code WPL305 - page 5

    ribbon, please refer to the ribbon calibration procedure to calibrate the ribbon sensor. NOTE: If you are using direct thermal labels you should not load a ribbon. 1. Push down on the ribbon access window to unlock and open the cover. 2. Wasp Ribbons come with the cardboard rewind core already attached to the ribbon for ease of accurate installatio ...

  • Wasp Bar Code WPL305 - page 6

    Make sure both the ribbon access window and the printer top cover are closed when powering up the printer. 3.3 Loading Label Stock 1. Insert a 1” label spindle into the label roll. If your paper core is 1 inch, you can remove the 1.5” core adapters from the centering tab. If the label width is 4 inches wide, the two centering tabs are not requi ...

  • Wasp Bar Code WPL305 - page 7

    Figure 6: Label installation 4. Feed the paper, printing side face up, under the Teflon bar and the paper guide and pass over the platen. 5. Adjust the yellow center-biased paper guides to slightly touch the edges of the label backing. 6. To close the printer top cover, lift the cover to the ultimate open angle then use both hands to close the cove ...

  • Wasp Bar Code WPL305 - page 8

    Figure 7: Top cover support is fixed at position 2 4. To close the cover, lift up the top cover to the ultimate angle then close the top cover gently and it will be kept at a stop position between 1 and 2 for a while. The cover will close automatically after several minutes. If you want to speed the closing, use both hands to gently push down the t ...

  • Wasp Bar Code WPL305 - page 9

    Figure 9: Use both hands to close the top cover 5. Do not force the cover! If you are not sure if top cover is locked at a stop position, please do not push top cover to close it or the top cover will be damaged. Instead, open the top cover as wide as it will go and close the cover again. Use both hands to push top cover to close it. ...

  • Wasp Bar Code WPL305 - page 10

    4. Power on Utilities There are three power-on utilities to set up and test printer hardware. 1. Printer initialization 2. Ribbon sensor calibration 3. Gap or black mark sensor calibration Note: You must run the #2 and #3 utilities after running the #1 to properly set up the printer. 4.1 Initialization Printer initialization is used to clear DRAM a ...

  • Wasp Bar Code WPL305 - page 11

    4.3 Gap/Black Mark Calibration Gap/black mark sensor sensitivity should be calibrated at the following conditions: 1. A brand new printer 2. Change label stock 3. Printer initialization Please follow the steps below to calibrate the sensor. 1. Turn the printer power off. 2. Press and hold the FEED button then turn on the printer. 3. The LED will tu ...

  • Wasp Bar Code WPL305 - page 12

    The printer will enter dump mode after printing the printer configuration. In dump mode, all characters will be printed in 2 columns as in the figure below. Figure 11: Dump mode printout The left side characters are received from your system and the right side data are the corresponding hexadecimal values of the characters. Dump mode allows users t ...

  • Wasp Bar Code WPL305 - page 13

    5. Maintenance 5.1 Cleaning Use one or more of the following supplies that meets your needs: n Cleaning pens n Cleaning swabs n Lint-free cloth Printer Part Method Printer Head n Let the print head to cool for one minute. n Use a cleaning pen to swab the print elements. Platen Roller n Rotate the platen roller and wipe it thoroughly with 70% alcoho ...

  • Wasp Bar Code WPL305 - page 14

    Utilities . 6.2 Print Quality Continuous feeding labels n The printer settings may be wrong. Please do the Initialization and Gap/Black Mark Calibration . No print on the label n Is the label or ribbon loaded correctly? Follow the instructions in Loading the Labels or Loading the Ribbon . n Has the ribbon run out? Follow the instructions in Loading ...

  • Wasp Bar Code WPL305 - page 15

    7. Specifications 7.1 Printer Specifications Item W305 Mechanism Resolution 203 dpi. Max. Print Width 108 mm. Max. Print Length 1000 mm ( 39” ). Ribbon Capacity 300 meter with 1” core. (Max. OD 67 mm) Printing Speed 2, 3, 4 and 5 ips. Peeler function 2, 3 ips Printing Method Direct thermal and thermal transfer printing. Enclosure Structure Dime ...

  • Wasp Bar Code WPL305 - page 16

    Wound Type Outside wound. Width 20mm ~ 112mm (0.78” ~ 4.4”). Length 10mm ~ 1000mm (0.4” ~ 39”). 25.4mm ~ 1000mm (1” ~ 39”).(for peeler and cutter) Thickness 0.06mm ~ 0.19mm. (2.3~7.4 mil), max. 150g/m 2 Roll Diameter 5”. Roll Core Diameter 25.4mm ~ 76.2mm (1” ~ 3”). Gap Height 2mm min. Black Mark Height 2mm min. Black Mark Width 8 ...

  • Wasp Bar Code WPL305 - page 17

    This warranty is limited to repair or replacement at Wasp Technologies’ option, with reasonable promptness after being notified. These provisions do not prolong the original warranty term for any product which has been repaired or replaced by Wasp Technologies. This warranty applies to the original owner and does not extend to any product which h ...

Manufacturer Wasp Bar Code Category Printer

Documents that we receive from a manufacturer of a Wasp Bar Code WPL305 can be divided into several groups. They are, among others:
- Wasp Bar Code technical drawings
- WPL305 manuals
- Wasp Bar Code product data sheets
- information booklets
- or energy labels Wasp Bar Code WPL305
All of them are important, but the most important information from the point of view of use of the device are in the user manual Wasp Bar Code WPL305.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Wasp Bar Code WPL305, service manual, brief instructions and user manuals Wasp Bar Code WPL305. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Wasp Bar Code WPL305.

Similar manuals

A complete manual for the device Wasp Bar Code WPL305, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Wasp Bar Code WPL305 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Wasp Bar Code WPL305.

A complete Wasp Bar Code manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Wasp Bar Code WPL305 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Wasp Bar Code WPL305, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Wasp Bar Code WPL305, that we can find in the current document
3. Tips how to use the basic functions of the device Wasp Bar Code WPL305 - which should help us in our first steps of using Wasp Bar Code WPL305
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Wasp Bar Code WPL305
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Wasp Bar Code WPL305 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Wasp Bar Code WPL305?

Use the form below

If you did not solve your problem by using a manual Wasp Bar Code WPL305, ask a question using the form below. If a user had a similar problem with Wasp Bar Code WPL305 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)