-
Hitachi DH 38MS - page 1
Rotary Hammer Model DH 38MS Handling instructions Note: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an important reference when using this power tool. 001Cover_DH38MS_Eng 11/25/08, 18:25 1 ...
-
Hitachi DH 38MS - page 2
2 GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains- operated (corded) power tool or ...
-
Hitachi DH 38MS - page 3
3 2. Anchor hole drilling (Rotation + Hammering) Drill bit (Taper shank) STANDARD ACCESSORIES (1) Case ............................................................................. 1 (2) Side Handle ................................................................ 1 Standard accessories are subject to change without notice. OPTIONAL ACCESSORIES (sol ...
-
Hitachi DH 38MS - page 4
4 (1) Center pin 䢇 Applied to core bits from 38 mm to 105 mm 䢇 Applied to core bits 32 mm and 35 mm NOTE: Do not use core bits 25 mm or 29 mm. (2) Core bit 䢇 External dia. 25, 29, 32, 35, 38, 45, 54, 64, 79, 94, 105 mm (with guide plate, not applicable to cores 25 mm or 29 mm) (3) Core bit shank 䢇 Applied to core bits above 38 mm 䢇 Applie ...
-
Hitachi DH 38MS - page 5
5 Fig. 1 (2) To attach the tool (SDS max shank), insert it into the hole until it contacts the innermost end of the hole as illustrated in Fig. 2 . If you continue to turn the tool with slight pressure, you can feel a spot where there is a hitch. At that spot, pull the grip to the direction of an arrow mark and insert the tool all the way until it ...
-
Hitachi DH 38MS - page 6
6 4. When demolishing and chiseling at “hammering”: CAUTION: 䡬 If the selector lever is switched during motor rotation, the tool can start to rotate abruptly, resulting in unexpected accidents. Make sure to switch the selector lever when the motor is at a complete stop. 䡬 If the bull point or cold chisel is used at the position of ”rotati ...
-
Hitachi DH 38MS - page 7
7 Fig. 10 (2) Turn the power on and drill a base hole to the depth sounded by indicating groove on the drill bit. (3) After cleaning out dust with a syringe, attach the plug to the anchor tip and drive in the anchor with a manual hammer. (4) To remove the drill bit (taper shank), insert the cotter into the slot of the taper shank adapter and strike ...
-
Hitachi DH 38MS - page 8
8 Fig. 14 (3) Insert the center pin into the guide plate until it reaches the extremity. (4) Fit in the guide plate by aligning its concaved portion with the core bit tip. When the position of the concave is shifted by turning the guide plate right or left, the guide plate never slips off even when the drill is used in a downward direction. ( Fig. ...
-
Hitachi DH 38MS - page 9
9 2. Grease replenishment CAUTION: Before replenishing the grease, turn the power off and pull out the power plug. (1) Remove the crank cover and wipe off the grease inside. ( Fig. 19 ) (2) Supply 60 g of Hitachi Electric Hammer Grease A (Standard accessory, contained in tube) to the crank case. (3) After replenishing the grease, install the crank ...
-
Hitachi DH 38MS - page 10
10 02Back_DH38MS_Eng 11/25/08, 18:25 10 ...
-
Hitachi DH 38MS - page 11
11 ITEM NO. PA RT NAME Q’TY 1 FRONT CAP 1 2 GRIP 1 3 STOPPER RING 1 4 NEEDLE HOLDER 1 5 RET AINER SPRING 1 6 SPRING HOLDER (A) 1 7 CYLINDER CASE 1 8 HEX. SOCKET HD. BOL T (W/FLANGE) M6 × 25 4 9 O-RING (1AS-60) 1 10 RET AINER DAMPER 1 11 RET AINER DAMPER W ASHER 1 12 RET AINER SLEEVE 1 13 NEEDLE ROLLER D8 × 20 2 14 O-RING (C) 1 15 SECOND HAMMER ...
-
Hitachi DH 38MS - page 12
101 Code No. C99177512 F Printed in China Hitachi Koki Co., Ltd. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan 02Back_DH38MS_Eng 12/3/10, 2:58 PM 12 ...
Hitachi DH 38MSについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもHitachi DH 38MSの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHitachi DH 38MSで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。