Hobart WS-80の取扱説明書

10ページ 1.48 mb
ダウンロード

ページに移動 of 10

Summary
  • Hobart WS-80 - page 1

    WS-40/80 Hobart Compact Water Softener Installation Instructions WS-40 WS-80 - NOTICE - This Manual is prepared for the use of trained Hobart Service Technicians and should not be used by those not properly qualified. This manual is not intended to be all encompassing. If you have not attended a Hobart Service School for this product, you should re ...

  • Hobart WS-80 - page 2

    TABLE OF CONTENTS INSTALLATION ............................................................................................ 3 INSTALLATION WS-40/80 .............................................................................. 3 DISC REPLACEMENT ...................................................................................... 8 DISC REPLACEMEN ...

  • Hobart WS-80 - page 3

    INSTALLATION INSTALLATION WS-40/80 SAVE THESE INSTRUCTIONS Disconnect the electrical power to the machine and follow lockout / tagout procedures. 1. Locate water supply line and appropriate drains for softener installation. 2. Install by-pass valving. Fig. 1 3. Install high temperature prefilter if needed. Fig. 2 4. Remove all items from shipping p ...

  • Hobart WS-80 - page 4

    Fig. 5 9. Install one O-Ring into each groove of the brass adapter. Fig. 6 10. Apply a small amount of seal lube evenly onto each O-ring. Fig. 7 11. Remove the pin and bracket from the softener in/ out port area. Fig. 8 12. Install the brass adapters into the in/out ports and secure by reinstalling the bracket and pin. Fig. 9 13. The female end of ...

  • Hobart WS-80 - page 5

    15. Insert tubing provided into the overflow port on the back of the softener and run drain lower than the cabinet connection to provide a gravity drain in the event of a internal cabinet leak. Fig. 10 16. Review the meter disc selection chart and the water analysis provided. If no water analysis is provided test the water supply. 17. To test the w ...

  • Hobart WS-80 - page 6

    Brine Valve Settings Unit Brine Setting Float Cup Height WS-40 1.0 lb. 6.25" WS-80 1.4 lb. 6.5" E. Reinstall brine valve into the cabinet. NOTE: Do not drop brine valve into drum. Dropping may lower float cup, resulting in an improper setting. 20. To install salt alarm system remove paper lining from back of salt alarm connector box. Fig. ...

  • Hobart WS-80 - page 7

    Fig. 17 27. Check for proper operation by pressing the recessed red button on bottom of salt alarm controller. If controller is operating properly - the indicator light will flash and an audible tone will be heard. Fig. 18 28. 29. Add a clean grade of salt at this time. Higher grades of Pelletized Salt for impurities and solubility should be used. ...

  • Hobart WS-80 - page 8

    DISC REPLACEMENT DISC REPLACEMENT WS-40/80 1. Remove screws and cap cover from level one. Fig. 19 2. Remove balance piston. Fig. 20 3. Remove balance piston o-ring and balance piston spring. Fig. 21 4. Remove meter drive pawl. Fig. 22 5. Remove meter disc. Fig. 23 WS-40/80 Hobart Compact Water Softener Installation Instructions - DISC REPLACEMENT F ...

  • Hobart WS-80 - page 9

    6. Install correct meter disc and reassemble in reverse order. NOTE: Be certain to start cap screws by hand rotating backwards until screw drops into thread then tighten. An alternating, crossing pattern should be used while tightening cap screws to ensure correct cap fit. WS-40/80 Hobart Compact Water Softener Installation Instructions - DISC REPL ...

  • Hobart WS-80 - page 10

    DISC SELECTION DISC SELECTION WS-40/80 The amount of hardness removed (in compensated gpg) will be based on the amount of brine and the meter disc selected. 1. Determine the compensated hardness. This requires a hardness test and an iron test on raw water at the application site. Compensated hardness is calculated by multiplying the ferrous iron (i ...

メーカー Hobart カテゴリー Water System

Hobart WS-80のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WS-80の取扱説明書
- Hobartの製品カード
- パンフレット
- またはHobart WS-80の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Hobart WS-80の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Hobart WS-80の取り付け説明書、サービスマニュアル、簡易説明書、またはHobart WS-80のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Hobart WS-80の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Hobart WS-80デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHobart WS-80を使用するのを助ける技術的文書のことです。説明書は通常、全てのHobart WS-80ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Hobartの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Hobart WS-80の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHobart WS-80の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Hobart WS-80に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Hobart WS-80デバイスの基本機能を使うにあたってのヒント。 Hobart WS-80のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Hobart WS-80に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHobart WS-80のメーカー/サービスへの連絡先に関する情報。

Hobart WS-80についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHobart WS-80の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHobart WS-80で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)