Norton Abrasives C9の取扱説明書

22ページ 0.5 mb
ダウンロード

ページに移動 of 22

Summary
  • Norton Abrasives C9 - page 1

    OWNERS MANUAL Small Concrete Saw MODEL: C9 FORM <<7418 3/2005 ...

  • Norton Abrasives C9 - page 2

    2 WARRANTY Norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of shipment to the customer. The responsibility of Norton under this warranty is limited to replacement or repair of defective parts at Norton's Gainesville, Georgia factory, or at a point designated ...

  • Norton Abrasives C9 - page 3

    3 Table Of Contents CONTENTS PAGE I. Preparation A. Safety Precautions 4-6 B. Assembly 7 C. C9 Series Concrete Saw Specifications 8 D. Engine Specifications 9 E. Pointer Alignment 9 II. Operation A. Blade Installation 9-10 B. Starting The Engine 10 C. Water Supply 10-11 D. Operating The Saw 11 E. Cutting Technique 12 III. Maintenance A. Engine 13-1 ...

  • Norton Abrasives C9 - page 4

    4 I. PREPARATION A. Safety Precautions Important! The following safety precautions must always be observed. Hazard Symbols Fuel (gasoline) is extremely flammable and its vapors can explode if ignited. Store gasoline only in approved containers, in well- ventilated, unoccupied approved ar eas, and away from sparks or flames. Do not fill the fuel tan ...

  • Norton Abrasives C9 - page 5

    5 Dust and Silica Warning Grinding/cutting/drilling of masonry, c oncrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respirator y disease, cancer, birth defects or other reproductive harm. If you are unfam iliar with the risks associated with the part ...

  • Norton Abrasives C9 - page 6

    6 1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previous use. 2. The blade collars and arbors s hould be cleaned and examined for damage before mounting the blade. 3. The blade must be properly fitted o ver the arbor with the drive pin on the outside coll ...

  • Norton Abrasives C9 - page 7

    7 I. PREPARATION B. Assembly The compact concrete saws are shipped completely assembled and ready for use except for diamond blade, gasoline, oil, and handle bar. Inspect the saw for shipping damage. If any damage is found, contact the shipper immediately and file a freight claim. The Norton Company is not responsible for any freight-related damage ...

  • Norton Abrasives C9 - page 8

    8 C. C9 Series Concrete Saw Specifications Dimensions/Weight Length (Working) 50” (1270 mm) Length (Transport) 40.5” (1029 mm) Width 20.5” (521 mm) Height 41” (1041 mm) Weight 195 lbs (88.6 kg) Engine Engine Mfg. Honda Model GX270 Spec No. GX 270K1QXC9 Engine Type Single Cylinder 4 Cycle Horse Power 9 hp (6.65 kW) @ 3,600 rpm Max Torque 19. ...

  • Norton Abrasives C9 - page 9

    9 D. Engine Prior to attempting to operate the engine, read the information contained in the engine owner's ma nual. An engine owners manual is supplied with every gasoline powered concrete saw. 1. Check Oil: Add oil if low. Refer to the engine owner's manual for the recommended SAE viscosity grades. Capacit y of oil is 1.1 liters (1.16 U ...

  • Norton Abrasives C9 - page 10

    10 2. Remove the blade shaft nut, (Turn clockwise) , and remove the outside collar. 3. Clean off any foreign particles on the clamping surfaces of both collars and on the mounting surface of the blade. 4. Place the blade on the blade shaft, lining up the drive pin hole in the blade with the drive pinhole in the inside collar. Use only Clipper Diamo ...

  • Norton Abrasives C9 - page 11

    11 stability. The water tank adds additional blast (weight) to the machine, which aids in keeping the diamond blade in the cut and reducing vibrations. We recommend that the wate r tank to be filled with water at all time the machine is in use. • Use Only Water In The Water Tank • Do Not Drink From The Tank D. Operating the Saw 1. For blade ins ...

  • Norton Abrasives C9 - page 12

    12 13. When moving the saw to a new location, be sure the blade is not touching the ground. Always pay close attention to where you are moving and where the blade is at all times. E. Cutting Technique Lower the blade into the concrete to the required depth by turning the hand wheel clockwise. Reduce the forward pressure if the saw begins to stall. ...

  • Norton Abrasives C9 - page 13

    13 III. MAINTENANCE A. Engine Follow the below schedule for engine maintenance. NOTE: Check the Honda Engine manual that came with the engine for any changes to the maintenance schedule. If the charts have any differences, follow the chart in the Honda Engine Manual. The Norton Company does not warranty the engine. If any warranty or service of the ...

  • Norton Abrasives C9 - page 14

    14 Always refer to the engine manual for mo re detailed information on checking the oil, changing oil, and oil capacity, ai r filter changes, and fuel type to use. Use only Honda air filters. Do not clean the air filter with gasoline or other flammable solvents. A fire or explosi on could result. To clean, follow the instructions found in the Honda ...

  • Norton Abrasives C9 - page 15

    15 For best results, bearings should be relubricated while in operation. Note: Due caution for personal safety must be observed when servicing rotating equipment. The grease should be pumped in slowly until a slight bead forms around the seals. This bead, in addition to acting as an indicator of adequate relubrication, provides additional protectio ...

  • Norton Abrasives C9 - page 16

    16 7. Line up the straight edge along the outside face of both pulleys as shown in the drawing. 8. Misalignment will show up as a gap between the pulley face and the straight edge. 9. Make sure that the width of t he outside land (area between the belt and the edge of the pulley) is equal on both pulleys. D. Depth Control The depth control (raising ...

  • Norton Abrasives C9 - page 17

    17 IV. PARTS LIST SECTION A. Ordering Information 1. List model number and serial number of machine. 2. List part number and serial num ber of part not the item number. 3. Wherever alternate par ts are shown due to product improvement, inspect the part you have and provide additional description as necessary. 4. Specify mode of shipping desired, su ...

  • Norton Abrasives C9 - page 18

    18 C9 Parts Drawing ...

  • Norton Abrasives C9 - page 19

    19 C9 Parts Drawing ...

  • Norton Abrasives C9 - page 20

    Service Parts List C9 POS Description Req P/N 1 Blade Shaft (Alone) 1 83280 2 Nut Blade Shaft ¾'' Lefthand Thread 1 227156 3 Bearings Blade Shaft (1) with Hardw are 2 72474 Screw M12 x 70 1.75 DIN931(ea) 2 27175 Washer M12 DIN125 (ea) 16 27505 Lock Washer M12 DIN127 (ea) 8 27581 Nut M12 1.75 DIN934(ea) 4 27007 Screw M12 x 45 1.75 DIN933 ...

  • Norton Abrasives C9 - page 21

    NOTES ...

  • Norton Abrasives C9 - page 22

    Norton Construction Products PO Box 2898 Gainesville, GA 30503 Phone: 800-554-8003 or 770-967-3954 (8:00 A.M. to 7:00 P.M. Eastern Time) Fax: 800-443-1092 or 770-967-7287 ...

メーカー Norton Abrasives カテゴリー Saw

Norton Abrasives C9のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- C9の取扱説明書
- Norton Abrasivesの製品カード
- パンフレット
- またはNorton Abrasives C9の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Norton Abrasives C9の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Norton Abrasives C9の取り付け説明書、サービスマニュアル、簡易説明書、またはNorton Abrasives C9のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Norton Abrasives C9の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Norton Abrasives C9デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがNorton Abrasives C9を使用するのを助ける技術的文書のことです。説明書は通常、全てのNorton Abrasives C9ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Norton Abrasivesの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Norton Abrasives C9の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははNorton Abrasives C9の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Norton Abrasives C9に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Norton Abrasives C9デバイスの基本機能を使うにあたってのヒント。 Norton Abrasives C9のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Norton Abrasives C9に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるNorton Abrasives C9のメーカー/サービスへの連絡先に関する情報。

Norton Abrasives C9についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもNorton Abrasives C9の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがNorton Abrasives C9で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)