English dropdown-ico

Manual Norton Abrasives C9

22 pages 0.5 mb
Download

Go to site of 22

Summary
  • Norton Abrasives C9 - page 1

    OWNERS MANUAL Small Concrete Saw MODEL: C9 FORM <<7418 3/2005 ...

  • Norton Abrasives C9 - page 2

    2 WARRANTY Norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of shipment to the customer. The responsibility of Norton under this warranty is limited to replacement or repair of defective parts at Norton's Gainesville, Georgia factory, or at a point designated ...

  • Norton Abrasives C9 - page 3

    3 Table Of Contents CONTENTS PAGE I. Preparation A. Safety Precautions 4-6 B. Assembly 7 C. C9 Series Concrete Saw Specifications 8 D. Engine Specifications 9 E. Pointer Alignment 9 II. Operation A. Blade Installation 9-10 B. Starting The Engine 10 C. Water Supply 10-11 D. Operating The Saw 11 E. Cutting Technique 12 III. Maintenance A. Engine 13-1 ...

  • Norton Abrasives C9 - page 4

    4 I. PREPARATION A. Safety Precautions Important! The following safety precautions must always be observed. Hazard Symbols Fuel (gasoline) is extremely flammable and its vapors can explode if ignited. Store gasoline only in approved containers, in well- ventilated, unoccupied approved ar eas, and away from sparks or flames. Do not fill the fuel tan ...

  • Norton Abrasives C9 - page 5

    5 Dust and Silica Warning Grinding/cutting/drilling of masonry, c oncrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respirator y disease, cancer, birth defects or other reproductive harm. If you are unfam iliar with the risks associated with the part ...

  • Norton Abrasives C9 - page 6

    6 1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previous use. 2. The blade collars and arbors s hould be cleaned and examined for damage before mounting the blade. 3. The blade must be properly fitted o ver the arbor with the drive pin on the outside coll ...

  • Norton Abrasives C9 - page 7

    7 I. PREPARATION B. Assembly The compact concrete saws are shipped completely assembled and ready for use except for diamond blade, gasoline, oil, and handle bar. Inspect the saw for shipping damage. If any damage is found, contact the shipper immediately and file a freight claim. The Norton Company is not responsible for any freight-related damage ...

  • Norton Abrasives C9 - page 8

    8 C. C9 Series Concrete Saw Specifications Dimensions/Weight Length (Working) 50” (1270 mm) Length (Transport) 40.5” (1029 mm) Width 20.5” (521 mm) Height 41” (1041 mm) Weight 195 lbs (88.6 kg) Engine Engine Mfg. Honda Model GX270 Spec No. GX 270K1QXC9 Engine Type Single Cylinder 4 Cycle Horse Power 9 hp (6.65 kW) @ 3,600 rpm Max Torque 19. ...

  • Norton Abrasives C9 - page 9

    9 D. Engine Prior to attempting to operate the engine, read the information contained in the engine owner's ma nual. An engine owners manual is supplied with every gasoline powered concrete saw. 1. Check Oil: Add oil if low. Refer to the engine owner's manual for the recommended SAE viscosity grades. Capacit y of oil is 1.1 liters (1.16 U ...

  • Norton Abrasives C9 - page 10

    10 2. Remove the blade shaft nut, (Turn clockwise) , and remove the outside collar. 3. Clean off any foreign particles on the clamping surfaces of both collars and on the mounting surface of the blade. 4. Place the blade on the blade shaft, lining up the drive pin hole in the blade with the drive pinhole in the inside collar. Use only Clipper Diamo ...

  • Norton Abrasives C9 - page 11

    11 stability. The water tank adds additional blast (weight) to the machine, which aids in keeping the diamond blade in the cut and reducing vibrations. We recommend that the wate r tank to be filled with water at all time the machine is in use. • Use Only Water In The Water Tank • Do Not Drink From The Tank D. Operating the Saw 1. For blade ins ...

  • Norton Abrasives C9 - page 12

    12 13. When moving the saw to a new location, be sure the blade is not touching the ground. Always pay close attention to where you are moving and where the blade is at all times. E. Cutting Technique Lower the blade into the concrete to the required depth by turning the hand wheel clockwise. Reduce the forward pressure if the saw begins to stall. ...

  • Norton Abrasives C9 - page 13

    13 III. MAINTENANCE A. Engine Follow the below schedule for engine maintenance. NOTE: Check the Honda Engine manual that came with the engine for any changes to the maintenance schedule. If the charts have any differences, follow the chart in the Honda Engine Manual. The Norton Company does not warranty the engine. If any warranty or service of the ...

  • Norton Abrasives C9 - page 14

    14 Always refer to the engine manual for mo re detailed information on checking the oil, changing oil, and oil capacity, ai r filter changes, and fuel type to use. Use only Honda air filters. Do not clean the air filter with gasoline or other flammable solvents. A fire or explosi on could result. To clean, follow the instructions found in the Honda ...

  • Norton Abrasives C9 - page 15

    15 For best results, bearings should be relubricated while in operation. Note: Due caution for personal safety must be observed when servicing rotating equipment. The grease should be pumped in slowly until a slight bead forms around the seals. This bead, in addition to acting as an indicator of adequate relubrication, provides additional protectio ...

  • Norton Abrasives C9 - page 16

    16 7. Line up the straight edge along the outside face of both pulleys as shown in the drawing. 8. Misalignment will show up as a gap between the pulley face and the straight edge. 9. Make sure that the width of t he outside land (area between the belt and the edge of the pulley) is equal on both pulleys. D. Depth Control The depth control (raising ...

  • Norton Abrasives C9 - page 17

    17 IV. PARTS LIST SECTION A. Ordering Information 1. List model number and serial number of machine. 2. List part number and serial num ber of part not the item number. 3. Wherever alternate par ts are shown due to product improvement, inspect the part you have and provide additional description as necessary. 4. Specify mode of shipping desired, su ...

  • Norton Abrasives C9 - page 18

    18 C9 Parts Drawing ...

  • Norton Abrasives C9 - page 19

    19 C9 Parts Drawing ...

  • Norton Abrasives C9 - page 20

    Service Parts List C9 POS Description Req P/N 1 Blade Shaft (Alone) 1 83280 2 Nut Blade Shaft ¾'' Lefthand Thread 1 227156 3 Bearings Blade Shaft (1) with Hardw are 2 72474 Screw M12 x 70 1.75 DIN931(ea) 2 27175 Washer M12 DIN125 (ea) 16 27505 Lock Washer M12 DIN127 (ea) 8 27581 Nut M12 1.75 DIN934(ea) 4 27007 Screw M12 x 45 1.75 DIN933 ...

  • Norton Abrasives C9 - page 21

    NOTES ...

  • Norton Abrasives C9 - page 22

    Norton Construction Products PO Box 2898 Gainesville, GA 30503 Phone: 800-554-8003 or 770-967-3954 (8:00 A.M. to 7:00 P.M. Eastern Time) Fax: 800-443-1092 or 770-967-7287 ...

Manufacturer Norton Abrasives Category Saw

Documents that we receive from a manufacturer of a Norton Abrasives C9 can be divided into several groups. They are, among others:
- Norton Abrasives technical drawings
- C9 manuals
- Norton Abrasives product data sheets
- information booklets
- or energy labels Norton Abrasives C9
All of them are important, but the most important information from the point of view of use of the device are in the user manual Norton Abrasives C9.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Norton Abrasives C9, service manual, brief instructions and user manuals Norton Abrasives C9. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Norton Abrasives C9.

Similar manuals

A complete manual for the device Norton Abrasives C9, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Norton Abrasives C9 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Norton Abrasives C9.

A complete Norton Abrasives manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Norton Abrasives C9 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Norton Abrasives C9, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Norton Abrasives C9, that we can find in the current document
3. Tips how to use the basic functions of the device Norton Abrasives C9 - which should help us in our first steps of using Norton Abrasives C9
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Norton Abrasives C9
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Norton Abrasives C9 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Norton Abrasives C9?

Use the form below

If you did not solve your problem by using a manual Norton Abrasives C9, ask a question using the form below. If a user had a similar problem with Norton Abrasives C9 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)