日本語 dropdown-ico

Meyer Sound HM-1Sの取扱説明書

18ページ 1.05 mb
ダウンロード

ページに移動 of 18

Summary
  • Meyer Sound HM-1S - page 1

    Patents Pending Operating Instructions HM-1S Self-Powered S tudio Monitor Copyright © 1998 Meyer Sound Laboratories, Inc. All rights reserved Part # 05.059.004.01 Rev A2 ...

  • Meyer Sound HM-1S - page 2

    2 Introduction .......................................................... 3 Power Requirements ............................................ 3 Power Cable Requirements .................................. 5 Audio Input ........................................................... 5 The HM-1S Subwoofer ......................................... 5 Cooling ...

  • Meyer Sound HM-1S - page 3

    3 Introduction The Meyer HM-1S S tudio Monitor is a compact, full- range, self-powered reference monitor that employs a concentric tweeter mounting structure to achieve true point-source performance. Sophisticated phase-correc- tion circuitry provides superb imaging without the off-axis cancellation effect s, back-wave interference, and IM dis- tor ...

  • Meyer Sound HM-1S - page 4

    4 Power Supplies for Larger Systems If an installation includes more than 10 speakers, or requires several speakers to operate from a single 48 V line, a single, high-output power supply should be considered. The following sections provide current and voltage specifications for the HM-1S s power requirements. Current Ratings The wide dynamic ran ...

  • Meyer Sound HM-1S - page 5

    5 audio interruption. In the third, and preferable case, supplies that feature voltage foldback allow brief periods of current-limit without audio interruption; for this reason, we recommend using such supplies. The HM-1S does not require tight voltage regulation and operates down to 35 V although peak SPL values are reduced. This operating voltage ...

  • Meyer Sound HM-1S - page 6

    6 HM-1S Speaker Cable The following drawings and procedures are provided as an aid in the event that the speaker cable used to connect the HM-1S to the HM-1S Subwoofer needs to be repaired or extended. In cases where the original speaker cable has been modified, be sure to complete the Subwoofer Performance V erification section on page 10 of this ...

  • Meyer Sound HM-1S - page 7

    7 HM-1S to HM-1S Subwoofer Cable Connector Assembly Procedure Cable Boot Cord Connector Cable Clamp Housing Contact Pins Coupling Ring Step 1: Feed the end of the cable through the boot, cable clamp housing, and coupling ring in the order and position shown. Cable 3/8" Max. 7/32" Step 2: FOR STEREO CABLES: Strip cable as shown and begin s ...

  • Meyer Sound HM-1S - page 8

    8 Subwoofer Performance V erification There are two methods of verifying that the phase relationship between the HM-1S and its subwoofer. One method is free field, the other is a ground plane measurement in half space. Free Field: Place the HM-1S directly above and coplanar to the subwoofer as pictured below: Place a calibrated measurement micropho ...

  • Meyer Sound HM-1S - page 9

    9 This represents a typical response of the HM-1S in free-field environment, on axis at 1 meter. This measurement was performed in the large anechoic chamber at MSLI. Connect the subwoofer and measure the combined response of the system. HM-1S on axis at 1 meter , free field. ...

  • Meyer Sound HM-1S - page 10

    10 This represents a typical response of the HM-1S and subwoofer, in phase, in a free field environment on axis at 1 meter. This measurement was performed in the large anechoic chamber at MSLI. This response indicates a complementary phase relationship between the HM-1S and subwoofer. HM-1S with in-phase subwoofer on axis at 1 meter , free field. ...

  • Meyer Sound HM-1S - page 11

    11 If the subwoofer is out of phase, the combined response will have a significant loss of energy compared to the overall response at around 82 Hz as illustrated below: HM-1S with out-of-phase subwoofer on axis at 1 meter , free field. ...

  • Meyer Sound HM-1S - page 12

    12 This represents a typical response of the HM-1S and subwoofer out-of-phase phase, in a free field environment on- axis at 1 meter. This measurement was performed in the large anechoic chamber at MSLI. If your system response indicates a phase reversal please contact Meyer Sound Technical Support for assistance. Half Sp ace: To verify the system ...

  • Meyer Sound HM-1S - page 13

    13 This represents a typical ground-plane response of the HM-1S, on-axis at 1 meter. Keep in mind that any surface close to the test space can create reflections which will change the response of the speaker. Connect the subwoofer to the HM-1S and measure the combined response of the system. HM-1S on axis at 1 meter , ground plane. ...

  • Meyer Sound HM-1S - page 14

    14 HM-1S with in-phase Subwoofer on axis at 1 meter , ground plane. This represents a typical ground-plane response of the HM-1S and subwoofer, in phase, at 1 meter. This response indicates a complementary phase relationship between the HM-1S and subwoofer. ...

  • Meyer Sound HM-1S - page 15

    15 HM-1S with out-of-phase Subwoofer on axis at 1 meter , ground plane. If the subwoofer is out of phase the combined response will have a significant loss of energy compared to the overall response at around 82 Hz as illustrated below: This represents a typical ground plane response of the HM-1S and subwoofer out-of-phase, in a ground plane enviro ...

  • Meyer Sound HM-1S - page 16

    16 Cooling and Fan Installation The HM-1S depends on natural convection to cool the heatsinks that absorb heat from the amplifiers and radiate the heat into the surrounding air space. Natural convection requires free air in back of, and underneath the HM-1S to allow air to flow up over the heatsinks. The HM-1S reaches an equilibrium temperature in ...

  • Meyer Sound HM-1S - page 17

    17  T o reduce the risk of electric shock, disconnect the loud- speaker from the AC adapter before installing audio cable. Reconnect the adapter only after making all signal con- nections.  Connect the AC adapter to a two-pole, three wire grounding mains receptacle. The recept acle must be connected to a fuse or circuit breaker . Connection t ...

  • Meyer Sound HM-1S - page 18

    18 Meyer Sound Laboratories, Inc. 2832 San Pablo Avenue Berkeley, California 94702 Telephone: 510 - 486 - 1166 FAX: 510 - 486 - 8356 E-mail: techsupport@meyersound.com http://www.meyersound.com Dimensions All units in inches HM-1S weighs 11.0 lb (5.0 kg); HM-1S Subwoofer weighs 33 lb (15 kg) Rear Panel Connectors Meyer Sound Germany GmbH Carl Zeiss ...

メーカー Meyer Sound カテゴリー Speaker System

Meyer Sound HM-1Sのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HM-1Sの取扱説明書
- Meyer Soundの製品カード
- パンフレット
- またはMeyer Sound HM-1Sの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Meyer Sound HM-1Sの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Meyer Sound HM-1Sの取り付け説明書、サービスマニュアル、簡易説明書、またはMeyer Sound HM-1Sのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Meyer Sound HM-1Sの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Meyer Sound HM-1Sデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMeyer Sound HM-1Sを使用するのを助ける技術的文書のことです。説明書は通常、全てのMeyer Sound HM-1Sユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Meyer Soundの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Meyer Sound HM-1Sの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMeyer Sound HM-1Sの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Meyer Sound HM-1Sに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Meyer Sound HM-1Sデバイスの基本機能を使うにあたってのヒント。 Meyer Sound HM-1Sのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Meyer Sound HM-1Sに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMeyer Sound HM-1Sのメーカー/サービスへの連絡先に関する情報。

Meyer Sound HM-1Sについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもMeyer Sound HM-1Sの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMeyer Sound HM-1Sで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)