Grizzly H3118の取扱説明書

27ページ 1.12 mb
ダウンロード

ページに移動 of 27

Summary
  • Grizzly H3118 - page 1

    TILE SAW MODEL H3118 INSTRUCTION MANUAL COPYRIGHT © JANUARY 2003 BY GRIZZLY INDUSTRIAL, INC WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN CHINA ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS ...

  • Grizzly H3118 - page 2

    WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonr ...

  • Grizzly H3118 - page 3

    TABLE OF CONTENTS PAGE 1. SAFETY ....................................................................................................................... ...............................2 Safety Instructions For Power Tools ................................................................................................2-3 Safety Instructions for Tile ...

  • Grizzly H3118 - page 4

    -2- H3118 Tile Saw SECTION 1: SAFETY Safety Instructions For Power Tools 5. KEEP CHILDREN AND VISITORS AWAY . All children and visitors should be kept at a safe distance from work area. 6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys. 7. NEVER FORCE TOOL . It will do the job better and safer at the rate for ...

  • Grizzly H3118 - page 5

    H3118 Tile Saw -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension co ...

  • Grizzly H3118 - page 6

    -4- H3118 Tile Saw 1. Wet Hands: DO NOT touch electrical con- nections with wet hands. 2. Plug In: All plug and receptacles must be off the ground and in a dry location. 3. Drip Loop : Always make a drip loop with the power cord when using the saw ( Figure 4, Page 11 ). 4. GFCI: Always use a GFCI outlet in the electrical circuit of the saw ( Figure ...

  • Grizzly H3118 - page 7

    H3118 Tile Saw -5- SECTION 2: INTRODUCTION We are proud to offer the Grizzly Model H3118 Tile Saw. The Model H3118 is part of a growing Grizzly family of fine machinery. When used according to the guidelines set forth in this man- ual, you can expect years of trouble-free, enjoy- able operation and proof of Grizzly’s commitment to customer satisf ...

  • Grizzly H3118 - page 8

    -6- H3118 Tile Saw SECTION 3: CIRCUIT REQUIREMENTS 110V Operation Figure 1. NEMA 5-15 plug and GFCI outlet. T E S T R E S E T Grounding Prong GFCI Outlet Current Carrying Prongs Amperage Draw The Model H3118 is wired to operate at 110V and draws approximately 3.75 amps. Plug & Outlet Type The Model H3118 is supplied with a NEMA 5-15 plug. A Gro ...

  • Grizzly H3118 - page 9

    H3118 Tile Saw -7- Grounding Extension Cord Reduce the risk of elec- trocution by keeping all connections dry and off the ground. DO NOT touch plugs with wet hands. Failure to follow these warning could result in serious injury. No single list of electrical guidelines can be comprehensive for all shop environ- ments. Operating this machinery may re ...

  • Grizzly H3118 - page 10

    -8- H3118 Tile Saw Clean Up Site Considerations Unsupervised children and visitors entering a shop could receive seri- ous personal injury. Ensure child and visitor safety by keeping all entrances to the shop locked at all times. DO NOT allow unsupervised children or visitors in the shop at any time. Unpainted surfaces may be coated with a waxy oil ...

  • Grizzly H3118 - page 11

    H3118 Tile Saw -9- Main Features Power Switch Power Cord Table Tilting Mechanism Table Rip Fence Water Tray Blade Cover Blade Blade Guard Figure 2. Front view of saw. Set up and operation instructions will be easier to understand if you become familiar with the location and names of the basic features of the saw. Match up the feature list below wit ...

  • Grizzly H3118 - page 12

    -10- H3118 Tile Saw Assembly Figure 3. Attaching the rubber feet. The Model H3118 comes pre-assembled from the factory except for the four rubber feet that need inserting as shown in Figure 3 . Dip the rubber feet into soapy water to ease the installation. Note–DO NOT twist the rubber feet during instal- lation. They could break. Use only a wiggl ...

  • Grizzly H3118 - page 13

    H3118 Tile Saw -11- Before starting the machine: 1. Read this manual and make sure you follow all safety precautions before operating this machine. 2. Make sure the blade guard is installed and is covering the blade above the table surface. 3. Make sure the blade cover is installed and is covering the blade below the table. 4. Make sure all tools o ...

  • Grizzly H3118 - page 14

    -12- H3118 Tile Saw Lubrication Water is used to cool and lubricate the saw blade when cutting tile. Water also reduces the amount of tile dust produced. Fill the water tray with water before making any tile cuts. The water level should be above the blade cover base when the water tray is under the saw as shown in Figure 6 . Figure 6. Water tray. F ...

  • Grizzly H3118 - page 15

    H3118 Tile Saw -13- Cut Preparation Cutting To make a cut: 1. Using a marking pencil, mark the cut line on a piece of tile. 2. Unlock the rip fence ( Figure 7 ) and slide it to the edge of the table. 3. Line up the cut line on the tile with the saw blade. 4. Adjust the rip fence against the edge of the tile and lock the rip fence into position. 5. ...

  • Grizzly H3118 - page 16

    -14- H3118 Tile Saw Figure 8. Diagonal cutting with the miter gauge. 45˚ Miter Cutting Diagonal cuts can be made on rectangular tiles using the supplied miter gauge. Figure 8 shows a typical set up for cutting the corner off of a square tile. Figure 9. Tilting the table for bevel cutting. Bevel Cutting The saw table can be tilted up to 45˚ to acc ...

  • Grizzly H3118 - page 17

    H3118 Tile Saw -15- SECTION 6: MAINTENANCE General Regular periodic maintenance on your Model H3118 will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Before each use, perform the following checks: • Look for conditions allowing prolonged expo- sure of the motor and electrical components to water. ? ...

  • Grizzly H3118 - page 18

    -16- H3118 Tile Saw Blade Changes To change/install the blade: 1. Unplug the machine from the power source! 2. Remove the water tray from underneath the tile saw. 3. Remove the blade cover by removing the screws on each side of the blade cover ( Figure 10 ). Figure 10. Loosening one of the blade cover screws. 4. Use a 19mm and an 8mm open-end wrenc ...

  • Grizzly H3118 - page 19

    H3118 Tile Saw -17- SECTION 7: REFERENCE INFO If you need parts or help in assembling your machine, or if you need operational information, call the Grizzly Service Department. Trained ser- vice technicians will be glad to help you. If you have any comments regarding this manual, please write to Grizzly at the address below: Grizzly Industrial, Inc ...

  • Grizzly H3118 - page 20

    -18- H3118 Tile Saw Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Design Type ..........................................................................................................Benchtop Overall Dimensions: Table Height ........................................................ ...

  • Grizzly H3118 - page 21

    PARTS DIAGRAM AND LIST -19- H3118 Tile Saw ...

  • Grizzly H3118 - page 22

    -20- H3118 Tile Saw 26 PS08M PHLP HD SCR M5-0.8 X 12 27 PH3118027 PLATE 28 PH3118028 CONNECTION PLATE 29 PH3118029 FRAME 30 PS38M PHLP HD SCR M4-0.7 X 10 31 PN01M HEX NUT M6-1.0 32 PH3118032 HANDLE 33 PB02M HEX BOLT M6-1.0 X 12 34 PH3118034 MOTOR 35 PS17M PHLP HD SCR M4-0.7 X 6 36 PH3118036 REAR COVER 37 PTLW06M EXT TOOTH WASHER 4MM 38 PN23M HEX NU ...

  • Grizzly H3118 - page 23

    H3118 Tile Saw -21- NOTES ...

  • Grizzly H3118 - page 24

    -22- H3118 Tile Saw Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty ...

  • Grizzly H3118 - page 25

    CUT ALONG DOTTED LINE 9. How many of your woodworking machines are Grizzly? _____________ 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ...

  • Grizzly H3118 - page 26

    Place Stamp Here FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_______________________________ Street_______________________________ City______________State______Zip______ Send a Grizzly Catalog to a friend: ...

  • Grizzly H3118 - page 27

    Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! -OR- • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR Visit Our Website T oday And Discover Why Grizzly ® Is The Industry Leader! Call Today For A FREE Full Color Catalog ...

メーカー Grizzly カテゴリー Saw

Grizzly H3118のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- H3118の取扱説明書
- Grizzlyの製品カード
- パンフレット
- またはGrizzly H3118の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Grizzly H3118の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Grizzly H3118の取り付け説明書、サービスマニュアル、簡易説明書、またはGrizzly H3118のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Grizzly H3118の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Grizzly H3118デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGrizzly H3118を使用するのを助ける技術的文書のことです。説明書は通常、全てのGrizzly H3118ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Grizzlyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Grizzly H3118の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGrizzly H3118の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Grizzly H3118に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Grizzly H3118デバイスの基本機能を使うにあたってのヒント。 Grizzly H3118のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Grizzly H3118に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGrizzly H3118のメーカー/サービスへの連絡先に関する情報。

Grizzly H3118についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGrizzly H3118の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGrizzly H3118で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)