English dropdown-ico

Manual Grizzly H3118

27 pages 1.12 mb
Download

Go to site of 27

Summary
  • Grizzly H3118 - page 1

    TILE SAW MODEL H3118 INSTRUCTION MANUAL COPYRIGHT © JANUARY 2003 BY GRIZZLY INDUSTRIAL, INC WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN CHINA ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS ...

  • Grizzly H3118 - page 2

    WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonr ...

  • Grizzly H3118 - page 3

    TABLE OF CONTENTS PAGE 1. SAFETY ....................................................................................................................... ...............................2 Safety Instructions For Power Tools ................................................................................................2-3 Safety Instructions for Tile ...

  • Grizzly H3118 - page 4

    -2- H3118 Tile Saw SECTION 1: SAFETY Safety Instructions For Power Tools 5. KEEP CHILDREN AND VISITORS AWAY . All children and visitors should be kept at a safe distance from work area. 6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys. 7. NEVER FORCE TOOL . It will do the job better and safer at the rate for ...

  • Grizzly H3118 - page 5

    H3118 Tile Saw -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension co ...

  • Grizzly H3118 - page 6

    -4- H3118 Tile Saw 1. Wet Hands: DO NOT touch electrical con- nections with wet hands. 2. Plug In: All plug and receptacles must be off the ground and in a dry location. 3. Drip Loop : Always make a drip loop with the power cord when using the saw ( Figure 4, Page 11 ). 4. GFCI: Always use a GFCI outlet in the electrical circuit of the saw ( Figure ...

  • Grizzly H3118 - page 7

    H3118 Tile Saw -5- SECTION 2: INTRODUCTION We are proud to offer the Grizzly Model H3118 Tile Saw. The Model H3118 is part of a growing Grizzly family of fine machinery. When used according to the guidelines set forth in this man- ual, you can expect years of trouble-free, enjoy- able operation and proof of Grizzly’s commitment to customer satisf ...

  • Grizzly H3118 - page 8

    -6- H3118 Tile Saw SECTION 3: CIRCUIT REQUIREMENTS 110V Operation Figure 1. NEMA 5-15 plug and GFCI outlet. T E S T R E S E T Grounding Prong GFCI Outlet Current Carrying Prongs Amperage Draw The Model H3118 is wired to operate at 110V and draws approximately 3.75 amps. Plug & Outlet Type The Model H3118 is supplied with a NEMA 5-15 plug. A Gro ...

  • Grizzly H3118 - page 9

    H3118 Tile Saw -7- Grounding Extension Cord Reduce the risk of elec- trocution by keeping all connections dry and off the ground. DO NOT touch plugs with wet hands. Failure to follow these warning could result in serious injury. No single list of electrical guidelines can be comprehensive for all shop environ- ments. Operating this machinery may re ...

  • Grizzly H3118 - page 10

    -8- H3118 Tile Saw Clean Up Site Considerations Unsupervised children and visitors entering a shop could receive seri- ous personal injury. Ensure child and visitor safety by keeping all entrances to the shop locked at all times. DO NOT allow unsupervised children or visitors in the shop at any time. Unpainted surfaces may be coated with a waxy oil ...

  • Grizzly H3118 - page 11

    H3118 Tile Saw -9- Main Features Power Switch Power Cord Table Tilting Mechanism Table Rip Fence Water Tray Blade Cover Blade Blade Guard Figure 2. Front view of saw. Set up and operation instructions will be easier to understand if you become familiar with the location and names of the basic features of the saw. Match up the feature list below wit ...

  • Grizzly H3118 - page 12

    -10- H3118 Tile Saw Assembly Figure 3. Attaching the rubber feet. The Model H3118 comes pre-assembled from the factory except for the four rubber feet that need inserting as shown in Figure 3 . Dip the rubber feet into soapy water to ease the installation. Note–DO NOT twist the rubber feet during instal- lation. They could break. Use only a wiggl ...

  • Grizzly H3118 - page 13

    H3118 Tile Saw -11- Before starting the machine: 1. Read this manual and make sure you follow all safety precautions before operating this machine. 2. Make sure the blade guard is installed and is covering the blade above the table surface. 3. Make sure the blade cover is installed and is covering the blade below the table. 4. Make sure all tools o ...

  • Grizzly H3118 - page 14

    -12- H3118 Tile Saw Lubrication Water is used to cool and lubricate the saw blade when cutting tile. Water also reduces the amount of tile dust produced. Fill the water tray with water before making any tile cuts. The water level should be above the blade cover base when the water tray is under the saw as shown in Figure 6 . Figure 6. Water tray. F ...

  • Grizzly H3118 - page 15

    H3118 Tile Saw -13- Cut Preparation Cutting To make a cut: 1. Using a marking pencil, mark the cut line on a piece of tile. 2. Unlock the rip fence ( Figure 7 ) and slide it to the edge of the table. 3. Line up the cut line on the tile with the saw blade. 4. Adjust the rip fence against the edge of the tile and lock the rip fence into position. 5. ...

  • Grizzly H3118 - page 16

    -14- H3118 Tile Saw Figure 8. Diagonal cutting with the miter gauge. 45˚ Miter Cutting Diagonal cuts can be made on rectangular tiles using the supplied miter gauge. Figure 8 shows a typical set up for cutting the corner off of a square tile. Figure 9. Tilting the table for bevel cutting. Bevel Cutting The saw table can be tilted up to 45˚ to acc ...

  • Grizzly H3118 - page 17

    H3118 Tile Saw -15- SECTION 6: MAINTENANCE General Regular periodic maintenance on your Model H3118 will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Before each use, perform the following checks: • Look for conditions allowing prolonged expo- sure of the motor and electrical components to water. ? ...

  • Grizzly H3118 - page 18

    -16- H3118 Tile Saw Blade Changes To change/install the blade: 1. Unplug the machine from the power source! 2. Remove the water tray from underneath the tile saw. 3. Remove the blade cover by removing the screws on each side of the blade cover ( Figure 10 ). Figure 10. Loosening one of the blade cover screws. 4. Use a 19mm and an 8mm open-end wrenc ...

  • Grizzly H3118 - page 19

    H3118 Tile Saw -17- SECTION 7: REFERENCE INFO If you need parts or help in assembling your machine, or if you need operational information, call the Grizzly Service Department. Trained ser- vice technicians will be glad to help you. If you have any comments regarding this manual, please write to Grizzly at the address below: Grizzly Industrial, Inc ...

  • Grizzly H3118 - page 20

    -18- H3118 Tile Saw Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Design Type ..........................................................................................................Benchtop Overall Dimensions: Table Height ........................................................ ...

  • Grizzly H3118 - page 21

    PARTS DIAGRAM AND LIST -19- H3118 Tile Saw ...

  • Grizzly H3118 - page 22

    -20- H3118 Tile Saw 26 PS08M PHLP HD SCR M5-0.8 X 12 27 PH3118027 PLATE 28 PH3118028 CONNECTION PLATE 29 PH3118029 FRAME 30 PS38M PHLP HD SCR M4-0.7 X 10 31 PN01M HEX NUT M6-1.0 32 PH3118032 HANDLE 33 PB02M HEX BOLT M6-1.0 X 12 34 PH3118034 MOTOR 35 PS17M PHLP HD SCR M4-0.7 X 6 36 PH3118036 REAR COVER 37 PTLW06M EXT TOOTH WASHER 4MM 38 PN23M HEX NU ...

  • Grizzly H3118 - page 23

    H3118 Tile Saw -21- NOTES ...

  • Grizzly H3118 - page 24

    -22- H3118 Tile Saw Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty ...

  • Grizzly H3118 - page 25

    CUT ALONG DOTTED LINE 9. How many of your woodworking machines are Grizzly? _____________ 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ...

  • Grizzly H3118 - page 26

    Place Stamp Here FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_______________________________ Street_______________________________ City______________State______Zip______ Send a Grizzly Catalog to a friend: ...

  • Grizzly H3118 - page 27

    Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! -OR- • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR Visit Our Website T oday And Discover Why Grizzly ® Is The Industry Leader! Call Today For A FREE Full Color Catalog ...

Manufacturer Grizzly Category Saw

Documents that we receive from a manufacturer of a Grizzly H3118 can be divided into several groups. They are, among others:
- Grizzly technical drawings
- H3118 manuals
- Grizzly product data sheets
- information booklets
- or energy labels Grizzly H3118
All of them are important, but the most important information from the point of view of use of the device are in the user manual Grizzly H3118.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Grizzly H3118, service manual, brief instructions and user manuals Grizzly H3118. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Grizzly H3118.

Similar manuals

A complete manual for the device Grizzly H3118, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Grizzly H3118 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Grizzly H3118.

A complete Grizzly manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Grizzly H3118 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Grizzly H3118, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Grizzly H3118, that we can find in the current document
3. Tips how to use the basic functions of the device Grizzly H3118 - which should help us in our first steps of using Grizzly H3118
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Grizzly H3118
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Grizzly H3118 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Grizzly H3118?

Use the form below

If you did not solve your problem by using a manual Grizzly H3118, ask a question using the form below. If a user had a similar problem with Grizzly H3118 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)