ページに移動 of 52
1 Safety Guidelines 2 Specifications 2.1 S pecification Matrix 2.2 Ambient Condition 3 Use 4P a r t s 4.1 External View 4.2 Control Panel 5 Equipment 5.1 Monitor Display 5.2 Gauges 5.3 Fuel Line Changeover V alve 6 T ransport ation and installation 6.1 T ransport ation 6.2 Installat ion 7 Connection 7.1 Selecting Cable 7.2 Connecting Cable 7.3 Eart ...
- 1 - Introduction Thank you for purchasing Shindaiwa Sound Proof Diesel Engine Generator . z This user ’ s manual was created to ensure the safe operatio n of this equipment. Therefore, the manufacturer of this equipment strongly recommends that the user follow the instructions herein, to avoid unnecessary accidents and rep airs. z Please operat ...
- 3 - 1 Safety Guidelines :Suffocation from ex h aust fume Exhaust fume from the engine conta i n s m any el e ments harmful to human. Do not operate this equipment in poor ly ventilated area, such as inside a room or in a tunn e l :Electrical Shock Do not touch the output terminals during oper ation. Be sure to place covers over the ou ...
- 4 - :Injuries to ey es a nd skin Battery fluid cont ains d i luted su lfuric acid. Avoid cont act with eyes, skin or on clothing . If the acid comes in contac t, especially w ith eyes, flush with a lot o f water , a nd contact y our physician immediately . : Explosion Do not use the equip m e nt or charge the batte ry , in the case the ba ...
- 5 - :Injuries W h en lift i ng the equipment, alway s use a lift hook. Do not use Side rope-throu gh, for it may cause equipment to drop . Always pl a ce the equipment on a fl a t and stable surface , to keep the e qu ipment from sliding. W h en star ting the e ng i n e, turn off the connected equipment and set the cir c uit break ...
- 6 - Location of W arning labels When the warning labels become unreadable or damag e d, place new labels on the appropriate location, as spec i fied in the following figure. W hen orde r ing the label, use follow ing part nu m bers. 1 Operational Instruction Part Number 19401 - 00 361 2 Safety Instruction Part Number 19402 - 00 188 3 Suffocation ...
- 7 - 2 Spec i fica tions 2.1 S pecification Matrix Name of Gen erat o r DG1000MI-400 T ype Unit Blushless, Rotating Field, 3-Phase, 4-Po le, Synchronous AC Generator kV A 80 100 Rated O u tput kW 64 8 0 Rated V oltage (or the below ) V 200 220 Rated Curr ent (or the below) A 231 262 Rated V oltage V 400 440 Rated Curr en t A 1 15 131 Frequency Hz ...
- 8 - 2.2 A mbient Condition Use the equipmen t under the following a mbient condition. The other condition may cause trouble, insuffic ient output powe r or deterioration of durabi lity . Ambient T empera ture : -15ºC 40ºC Humidity : less than 80% Altitude : less than 300m 3 Use Power source for cons truction –use equipment, su ch as subme ...
- 9 - 4.2 Control p anel No. Name No. Name 1 3-phase circuit breake r 1 1 Wat er T emperature Gau ge 2 1-phase circuit breake r 12 Oil Pressure Gauge 3 V oltage Mete r 13 Fuel Gauge 4 Amp Meter 14 Hour Meter 5 Frequency Meter 15 Emergency S top Button 6 Earth Leakage Relay 16 Preheat Lamp 7 Panel Light & Generat ing Lamp 17 S tarter Sw itch 8 V ...
- 10 - WA TER TE MP 5 Equipment 5.1 Monitor Display This generator is equ i pp ed with m on i tori n g functi on fo r water /coolant temperature, oil pressure, battery charge, air filter flow , batte ry fluid level, and fuel level. When the e q uip ment is s tarted u nder normal condition, Oil Pr es sure and Battery Charge l a mps will flash whe n ...
- 11 - If the water leve l is n ormal, check for loose f an b elt o r poss ible w ater lea k in the c o o ling system, afte r the engine is coo led down. <Caution> I f the w ater l ev el is too low , the sensor cannot detect the w ater temperature. Be sure to chec k the wat e r l eve l in the radiator and the Coolant r eserv o ir tank pri ...
- 12 - 0 0 0 0 0 HOUR METER 5.1.3 Battery C ha rge Monitoring Lamp (c harge lamp) W h en the battery is not ab le to be charged d ur ing operat ion, t he battery charge-monitoring lamp will flash. In the event this occurs, sto p the engine consult with the authorized distr ibutor or our engineering section . <Caution> Battery Charge Monit ...
- 13 - 5.2.4 Fuel Ga u ge It shows the volume in the fuel tan k . W hen filled up , it show s F . W h en the hand is approach ing to E , the volume is coming to e mpty . Replenish fuel enough pr om p tly . 5.2.5 Generato r Ga uges 5.2.5.1 V oltage Meter V oltage M e ter display s the output vo ltage (Phase t o Phase ) from the generator . Please ch ...
- 14 - 5.2.6.2 Panel Li ght / Pilot Lamp Pilot Lamp indicates w hether or not generator is g enerating electric ity , when the engine is driv ing. 5.2.7 S w i tch 5.2.7.1 St arter Switch STOP W h en the switch is set to this position, all powe r will be of f. The switch must be se t to this position to remove the key . RUN The switch must be se t t ...
- 15 - Thermal Relay 5.2.7.4 Thermal Relay This relay se nds the s i g n a l to the 3-Phase c ircuit brea k er a n d the 1-Phase breaker to trip-o ff when over-current flows in the c ircuits. W h en the breaker trips-off, it is set at the m id dle o f ON and O FF . In the case, please recover the brea k er , according to the following procedure; S ...
- 16 - FIXING SC REW N UT FREQUEN CY ADJUSTING SCR E W THROTTLE LEVER 5.2.8.2 Throttle Lever Throttle Lever The lever is to ad just the engine speed. Set it to IDLING when the engine sta rts and warms-up or cools dow n. W h en the rated pow er is used, set it to RUN (50 or 60Hz). Frequency Adju sting Screw Set the th rottle lever to RUN and loosen ...
- 17 - <Caution> Always set the lever for 3-way valve b ac k to A position and cover t he external fue l inta ke and return port with the supplied plugs, a fter the hoses a r e re m oved. 5.3.2 Using fuel from external fuel ta n k Connect hoses fro m the external fuel t a n k to the external fue l in take a n d the external fuel return po ...
- 18 - 6 T ransport and Inst allation 6.1 T ransportation :Injuries W h en lift i ng the equipment, alway s use a lift hook. Do not use Side rope-throu gh to attach y our l ift h ook, f o r i t may cause equip ment to drop. 6.1.1 Lif ting Equipment Alway s use a Lift H oo k, when lifting the equipme nt f or transporta t ion . 6.1.2 T ranspo ...
- 19 - 6.2 Inst allation :Suffocation from ex haust fume Exhaust fume from the engine conta i n s m any el e ments harmful to human. Do not operate this equipment in poor ly ventilated area, such as inside a room or in a tunn e l :Suffocation fr om exhaust fume Do not point the exhaust fume toward pedestr ians or building. :Fire Always ...
- 20 - :Electrical da mages If the load exceed s the allowa ble amperage, the overheat ing may da m age the cable. If the cable i s either t o o l o n g or too small a gauge, there will be greater vo l t age dro p to loads, which m a y result in reduced performance in t he c o nnect e d loads , m a lfunction, or damages. <Caution> ...
- 21 - 7.2 Connecting Cable :Electrical Shoc k Before connecting o r disconnecting a loa d cable from ou tput t er m in als, a lways tu rn a circuit breaker to OFF po sition, s top the eng ine, a nd remove t h e engine key . A person p erformi ng the maintenance shou ld always keep the key . : Fire Do not connect AC output to any indoor w i ...
- 22 - 7.2.1.3 For 1-Phase Load(2) T erminal V o ltage: 200V/220 V (or 400V/440V) at 5 0Hz/60Hz 7.2.2 1-Phase O utput T erminals & Recept acles The ter minal V oltage : 1 00V/1 10V at 50Hz/60Hz only In the case of no use o f 3-Phase output pow e r , refer to the Following dra wing and chart. V oltag e (100V/1 10V) only (Unit: kV A) U1-U0 W 1- W ...
- 23 - 7.3 Earth Leakage Relay and Grounding : Electrical Sh ock Ground the every earth grounding terminal to the earth as set o ut i n the m a nual. If e ven one of all is unconnected by m is take or acciden t, it will b e m u ch mo re dangerous for human body than the –relay case , because leaking current inev itably goes thro ugh the body ...
- 24 - GROUNDING ROD EAR TH GROUNDIN G TERMINA L BONN ET GROUNDI NG TERMINA L INDI CA TING LAMP EAR TH LEAKAGE RELA Y TEST BUTTON RESET BUTTON <Caution> In the even t y ou cannot ground the generator to the earth, co nsult w ith the authorized distributor o r our engineering section 7.3.2 Operat ion Check :Electrical Shock Before turn ...
- 25 - 7.3.3 The earth leakage breaker relay has activa ted In the even t the earth leakage breaker relay ha s activated, t h e earth leakage indicating l a mp T urns ON and the 3-Phase ea rth lea kage breaker ( le ve r) trips of f to b e positioned in the middle between ON and OFF positions. In the a b ove cond i t ion, even t h ough y ou stop the ...
- 26 - OIL FILLER OIL GAUGE OK NOT ENOU GH TOO MUCH LOWER LIMIT UPPER LIMI T OIL GAUGE 8.1 Checking Engine Oil Please refer to the us e r’s manual for Eng i ne sep arately W h en checking f or eng ine oil, be sure to k eep the equipment leveled, and insert the oil gauge all the w ay . Prior to s t a r ting the equip ment, m a ke sure to fill the ...
- 27 - FULL LOW 8.2 Checking Coolant/water Also refer to the User’s Manual for Engine :Injuries B e f o re pe rf o rmi ng any equipment check or maintenance, stop th e engine , and re move the engine key . A person performing the maintenance should alway s k eep th e key . :Burns D o not ope n t he radiator cap while operating this equipm ...
- 28 - Replace LLC every 2 y e a rs or 1000 hours Mixture ratio (for reference only) : Ambienr temperature (Celsius) -15 -20 -30 Mixture ratio 30% 35% 45% 8.2.3 Coola nt Capac ity ( Unit: L) T ota l Coolant V olume ( including reservoir ta nk) 22.8 (1.5) T h e value of ( ) shows the reservoir ta nk`s volume. 8.3 Checking Fan Belt Also refer to ...
- 29 - 8.3.2 Conditio n Check for any da mage on the fan belt. Replace if necessa ry . <Caution> Refer to the User’s manual for Engine for adjusting and replacing o f the fan belt. 8.4 Checking Fuel :Fire Alway s w ipe any drip of Diesel fuel or o i l. Do not use this e quipment when a leak is found. Repair the equ i pment be fore u ...
- 30 - Notice: Do no t use home hea t ing oil o r gasoline in y our diesel eng ine; either ma y cause engine damage. 8.5 Checking Fuel, Engine Oil, and W ater le akage :Fire Do not use this equipment w hen a leak is found. Repair the eq uipment before use. Be sure to check for a ny fuel leak at the hose connection, and oil and coolant leak by o ...
- 31 - Replaci ng the battery T wo batteries are connected in series order . Whenever you replace battery or dis connect cables, alway s p roceed with the following steps, otherwise battery ma y short-circuit. 8.6.1 Replacing the battery inst alled o n the lef t s id e toward the control p anel: Remove the clamp a n d cable from negative (-) po ...
- 32 - FIXING SCREW FREQUENCY AD JUST IN G S CR EW THROTTLE LEVE R 9 Ope r ati on 9.1 Initializing / prepa ration :Suffocation from ex haust fume Exhaust fume from the en g ine co n t ains many elements ha rmf u l to human. Do not ope rate th is equip ment i n poorly ventilated a rea , such a s i ns ide a roo m or in a tunne l :Suffocation fr o ...
- 33 - <Caution> Do not drive the sta rt e r motor for more than 10 seconds successively If you need to resta rt, wait at least 30 se conds before the retry . Release the sta rt e r sw it c h, as soon as the engine is started Keep the engine idle f or a t least 5 minutes Set the throttle lever t o R UN. Ensure that the frequ ency mete ...
- 34 - 9.2 200/400 V oltage Changeover - Dual V oltage System The generator is incorporated w it h dua l vol tage s ystem. So, you can easily change 400/440V to 200 /220V or adverse ly . Y o u can get 200V or 400 V by changing the combin ation of output ter minals with bus plates :Electrical Shock Be sure to set the circu it breaker OFF and sto ...
- 35 - 3-PHASE 400/440 V The 3-phase volt a g e is energized to the 3 -phase output termina ls. Refer to 7-2. Connec t ing cable S tarting t he engine and turning the 3-phase breaker to ON, the 3-phase current is sent to the 3-phase output ter minals. 9.3 During Operation 9.3.1 P ost startu p c heck Make sure that a ll meters (gauges) a nd disp ...
- 36 - :Fire Always w ipe a ny dri p o f ga soline or oil. Add fuel to the fue l tank T urn the s tarter switch to <RUN> position. It will take app roximately 30 seconds to vacuum the air ou t. <Caution> Ensure that all the air is completely e xtracted from fuel line, by setti n g the throttle lever to IDLING and sta rt the engi ...
- 37 - EXTER NAL FUEL INT AKE (PLUG : PT -1/2) EXTE RNAL FUEL RETURN (PLUG : PT -1/2) 3 - Way va l ves A posi tion 3-Way valves 9.6 Connecting to External Fuel T a nk :Fire Alway s stop the engine , w hen w orking on the fuel line. Alway s w ipe any drip of Diesel fuel or o i l. Do not use this equ ipm e nt when a leak is found. Repair the ...
- 38 - 10 Maintenance :Electrical Shock ● Injuries B e f o re pe rf o rmi ng any equipment check or maintenance, stop th e engine , and re move the engine key . A person performing the maintenance should alway s k eep th e key . :Fire ● Burns W he n chec king e ngine, always s top the engine, and keep aw a y from fire. W a it until the ...
- 39 - Description S tartup check Every 200hrs Every 400hrs Every 500hrs Every 1000hrs Engine Side Clean each part s / tightening Engine oil checks / add oil Engine oil change ( 1 st time at 50 hr mark ) Oil Filter change ( 1 st time at 50 hr mark) Coolant level chec k / add coolant Exhaust color check Coolant change or 2 yr . Drain ex c e ss w ate ...
- 40 - 10.1 Oil Change Remove Oil Filler cap Loosen the engine o il drain plug and a llow the oil to drain fully Reinstal l the drain plug Add oil from oil filler an d fill up to the MAX level . Y ou should check the oil level on the o i l gauge Reinstal l the filler cap hand-t i ght <Caution> For the ty pes o f e ng i n e oil to u se a n ...
- 41 - 10.3 Cleaning / Changing A ir Filter Elem e n t Clean E ve ry 200 hours Replace Every 500 hours Loosen the bo lt that is holding the a ir cleaner and re move the cleaner ca p Unscrew the wing nut and remove the filter element Clean or replace the filter element, and reins tall it in reverse order <Caution> Always make sure that th ...
- 42 - 10.4 Draining W ater from W ater Se p arator W h en a float ( red) is at drain level, dra in water . Loosen the drain plug an d drain water . Screw the drain plug , w hen finishing drain. <Caution> Afte r draining finishes, ex tract the air in fue l lin e . (Refer to 9-3 During operation. ) 10.5 Cleaning / Changing Fuel Filter Loos ...
- 43 - 10.6 Clean gauze filter in water sep arator Clean Every 500 hours Loosen the lever and the n loosen the air extraction plug. T urn the ring nut counter -clockwise to remove the cup a nd the ga uze filt er after the fuel inside does no t come out from the l ever . Wa sh the gauze filter in Diesel fuel and reinsta ll the unit in the reverse or ...
- 44 - <Caution> Put a tray under the l e v er in order to catch spilled fuel wh en loosing the lever . Gaskets are attached to both end s of joint pipe. Be careful not to lose and install them in the unit without fail. Change both gauz e filter and eyeb o lt when gauze filter is damaged . Extract the air in fuel line after ga ...
- 45 - 10.9 Draining W ater from Fuel T ank Drain wate r Every 200 hours Unscrew the F uel drain plug Reinstall t he drain plug, after draining water fully 10.10 Changing Coolant / W ater Replace Every 2 ye ar s or 1000 h ours Remove the radia tor cap cover Remove the radia tor cap Loosen the draining plug on both the engine and radiator Afte r d r ...
- 46 - 1 1 long-term S torage : Electrica l Shock ● Injuries Before performing any e quipment check or ma intenance, stop the engine, and remove the engine key . A person performing the maintenance should alway s keep th e key . :Fire ● Burns T emperature around mu ffler and exhaust can ge t ex tremely high. Keep any i nflammable items ...
- 47 - 1 1.2 St acking :Injuries If y ou have t o st ack two generators in w arehouse, alway s proceed w ith the following step s . E nsure that there is no d ent on bonnet, loosing b olt or no bolt in the gener a tors. Al w a y s pla c e the generators on a flat and stable surface, to keep the equip ment from sliding, A nd to b e e ...
- 48 - 12 T rouble shooting :Electrical Shock Do not operate the equ ipment, if the equip m ent or you are wet. Before performing any eq u i p ment check or maintenance , stop the engine. :Injuries W h en per forming equipment check a nd maintenance, alw ays stop the engine. :Fire ● Burns Battery may emit some combustible gas, so ...
- 49 - Symptom Presumabl e Cause Action S tarter motor does not drive or speed is low . 1. Batter y ou tput is weak 2. Batter y i s d eteriorated 3. Batter y terminal is OFF or loo se 4. Batter y terminal is cor roded 5. S tart er switch or relay is defec tive 6. S t arter motor is defect i ve 1. Check / battery liquid/ or Charge 2. C ha nge ba tt ...
- 50 - Overheated 1. Engine thermostat is defective 2. Water temp sensor i s defect i ve 3. Water temp meter i s defect i v e 4. Fan b elt tension i s w eak 5. Coolant is insufficient 6. Radiat or core is clogged 1. Ask our distributor t o repa ir 2. Ask our distributor t o repa ir 3. Ask our distributor t o repa ir 4. Chec k/Adjust fan belt 5. Che ...
- 51 - 13 Generator Wir ing Diagram ...
- 52 - 14 Engine Wiri ng D i agra m ...
Shindaiwa DG1000MIのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DG1000MIの取扱説明書
- Shindaiwaの製品カード
- パンフレット
- またはShindaiwa DG1000MIの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Shindaiwa DG1000MIの取扱説明書に含まれています。
取扱説明書と呼ばれる文書のグループは、Shindaiwa DG1000MIの取り付け説明書、サービスマニュアル、簡易説明書、またはShindaiwa DG1000MIのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Shindaiwa DG1000MIの製品を使用するにあたって最も人気のある説明書を閲覧できます。
Shindaiwa DG1000MIデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがShindaiwa DG1000MIを使用するのを助ける技術的文書のことです。説明書は通常、全てのShindaiwa DG1000MIユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。
Shindaiwaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。
1. Shindaiwa DG1000MIの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははShindaiwa DG1000MIの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Shindaiwa DG1000MIに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Shindaiwa DG1000MIデバイスの基本機能を使うにあたってのヒント。 Shindaiwa DG1000MIのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Shindaiwa DG1000MIに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるShindaiwa DG1000MIのメーカー/サービスへの連絡先に関する情報。
Shindaiwa DG1000MIについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもShindaiwa DG1000MIの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがShindaiwa DG1000MIで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。