Emerson MCU200の取扱説明書

8ページ 0.2 mb
ダウンロード

ページに移動 of 8

Summary
  • Emerson MCU200 - page 1

    Each Mobrey ultrasonic control system requires a sensor to suit the specific application, plus a control unit. These installation instructions cover the Mobrey control units in the MCU200 series. 1. Sensor installation 2. Control unit installation 3. Applications: 3. 1Gain adjustment 3. 2 Liquid level alarm 3. 3Pump control and latching arms 3. 4Bl ...

  • Emerson MCU200 - page 2

    1 . Sensor Installation When the gap is filled with liquid, the piezoelectric receiver crystal converts the ultrasonic wave into an electrical signal, which is transmitted back to the control unit using a second coaxial cable. Usually the two coaxial cables to the sensor are in one overall sheath. The control unit circuitry is a feedback amplifier ...

  • Emerson MCU200 - page 3

    T wo cables are required per sensor . The RG178 should be used where the cable itself is subject to temperatures exceeding 74°C. 2 . Control Unit Installation All cable connections are made to the terminal blocks along the bottom edge of the pcb (see fig.5). Release the terminal screw before inserting the wire. 2.2 External Connections Protection ...

  • Emerson MCU200 - page 4

    2.3 Switch Settings in MCU200 Series (i) Gain switch (and potentiometer): See section 3. (ii) Frequency selection This slide switch is labelled “FREQ” and is located between the sensor terminal block E2, and the Aux input terminals. This selects the operating frequency of the MCU200 oscillator , which is either 3.7MHz (switch in the 'up&ap ...

  • Emerson MCU200 - page 5

    3.1 Gain adjustment Correct adjustment of the gain (HI/LO switch and potentiometer) is essential for proper operation of any ultrasonic sensor system. This adjusts the gain of the feedback amplifier in the control unit, which produces oscillation of the sensor when the coupling between the ultrasonic crystals is sufficient. Therefore the higher the ...

  • Emerson MCU200 - page 6

    3.3 Pump control and latching alarms The output relay of the MCU200 can be latched into the de- energised state. This latch is achieved by short circuiting the two terminals of the Auxiliary input, labelled as terminals 3 & 4 on the pc board (see figure 5). The relay will remain de- energised while the latching short circuit is applied. Only af ...

  • Emerson MCU200 - page 7

    3.4 Interface Detection 3.4.1. Suspended Solids blanket sludge discharge detection The Mobrey MCU200 control unit can be used in conjunction with a 433S sensor to provide sludge blanket level detection in a settling tank, facilitating the control of automatic desludging. Similarly , in conjunction with a Mobrey sludge pipe using a pair of 488S sens ...

  • Emerson MCU200 - page 8

    3.4.3. Interface detection between two immiscible similar liquids When liquids are ultrasonically very similar - as happens for example with paraffin and water - the procedure in section 3.4.2. produces very little difference between the two “false dry” points. In this case the “reflection” method of interface detection is used. If an ultra ...

メーカー Emerson カテゴリー Projection Television

Emerson MCU200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MCU200の取扱説明書
- Emersonの製品カード
- パンフレット
- またはEmerson MCU200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Emerson MCU200の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Emerson MCU200の取り付け説明書、サービスマニュアル、簡易説明書、またはEmerson MCU200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Emerson MCU200の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Emerson MCU200デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがEmerson MCU200を使用するのを助ける技術的文書のことです。説明書は通常、全てのEmerson MCU200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Emersonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Emerson MCU200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははEmerson MCU200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Emerson MCU200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Emerson MCU200デバイスの基本機能を使うにあたってのヒント。 Emerson MCU200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Emerson MCU200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるEmerson MCU200のメーカー/サービスへの連絡先に関する情報。

Emerson MCU200についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもEmerson MCU200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがEmerson MCU200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)