Hitachi H 65の取扱説明書

12ページ 0.23 mb
ダウンロード

ページに移動 of 12

Summary
  • Hitachi H 65 - page 1

    DEMOLITION HAMMER MODEL H 65 INSTRUCTION MANUAL Note: Before using this HITACHI Demolition Hammer, carefully read through this INSTRUCTION MANUAL to ensure efficient, safe operation. It is recommended that this INSTRUCTION MANUAL be kept readily available as an important reference when using this power tool. ...

  • Hitachi H 65 - page 2

    1 We sincerely thank you for selecting a HITACHI POWER TOOL. To operate this power tool safely and efficiently, please read this INSTRUCTION MANUAL carefully to get a good understanding of the precautions in operation, capacity of the power tool, use and the like. IMPORTANT INFORMATION: SAFETY RULES FOR THE POWER TOOL WARNING: When using the power ...

  • Hitachi H 65 - page 3

    2 Inspect extension cords periodically and replace them if damaged. Keep handles dry, clean, and free from oil and grease. 13. DISCONNECT POWER TOOLS. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches ...

  • Hitachi H 65 - page 4

    3 27. STOP OPERATION IMMEDIATELY IF ANY ABNORMALITY IS DETECTED. Should the power tool be detected as out of order or should other abnormalities be observed during operation, stop using the power tool immediately. 28. NEVER LEAVE THE POWER TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave the power tool until it comes to a complete stop. 29. C ...

  • Hitachi H 65 - page 5

    4 GROUNDING INSTRUCTIONS This power tool should be grounded while in use to protect the operator from electric shock. The power tool is equipped with a three-conductor cord and three-prong grounding type plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect the g ...

  • Hitachi H 65 - page 6

    5 EXTENSION CORD Use only three-wire extension cords that have three-prong grounding-type plugs and three- pole receptacles that accept the power tool’s plug. Replace or repair damaged extension cord. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current the power to ...

  • Hitachi H 65 - page 7

    6 NAME OF PARTS SPECIFICATIONS Motor Single-Phase, Series Commutator Motor Power Source Single-Phase, 115V AC, 60 Hz Current 11.4A Full-Load Impact Rate: 1,400/min Weight 39.7 lbs (18 kg) ACCESSORIES CAUTION: Only following genuine accessories for this power tool should be used. The use of any other attachment or accessory is not recommended becaus ...

  • Hitachi H 65 - page 8

    7 3. Scoop Overall length: 21-1/2” (546 mm) Code No.: 985233 4. Cutter Overall length: 20-1/2” (520 mm) Width: 3” (75 mm) Code No.: 985232 5. Electric Hammer Oil Capacity: 1 liter Code No.: 955009 APPLICATION This demolition hammer should be applied to breaking concrete, chipping off concrete, grooving, bar cutting, and driving piles in insta ...

  • Hitachi H 65 - page 9

    8 NOTE: Use a manual hammer to open/close the retainer as it is too heavy to move by hand. NOTE: When removing the accessory, such as a bull point, a cutter etc., follow the above procedure in reverse order. OPERATION 1. Pull the trigger switch after applying the tip of the bit to the crushing position. In some cases, it is necessary to punch the t ...

  • Hitachi H 65 - page 10

    9 3. Check the oil level once a day, confirming that oil is enough. 4. After feeding oil, securely clamp the oil gauge. NOTE: As an optional accessory, oil for the HITACHI Demolition Hammer (one liter) is sold separately. Use this oil when oil in the tank becomes less than the level indicated in Fig. 6 below. MAINTENANCE AND INSPECTION CAUTION: Be ...

  • Hitachi H 65 - page 11

    10 ...

  • Hitachi H 65 - page 12

    Issued by Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo 108-6020, Japan Distributed by 3950 Steve Reynolds Blvd. Norcross, GA 30093 Hitachi Koki Canada Co. 6395 Kestrel Road Mississauga ON L5T 1Z5 209 Code No. C99005463 N Printed in Japan 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 ...

メーカー Hitachi カテゴリー Power Hammer

Hitachi H 65のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- H 65の取扱説明書
- Hitachiの製品カード
- パンフレット
- またはHitachi H 65の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Hitachi H 65の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Hitachi H 65の取り付け説明書、サービスマニュアル、簡易説明書、またはHitachi H 65のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Hitachi H 65の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Hitachi H 65デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHitachi H 65を使用するのを助ける技術的文書のことです。説明書は通常、全てのHitachi H 65ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Hitachiの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Hitachi H 65の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHitachi H 65の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Hitachi H 65に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Hitachi H 65デバイスの基本機能を使うにあたってのヒント。 Hitachi H 65のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Hitachi H 65に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHitachi H 65のメーカー/サービスへの連絡先に関する情報。

Hitachi H 65についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHitachi H 65の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHitachi H 65で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)