English dropdown-ico

Manual KTI Networks KPOE-800-1P

17 pages 1.2 mb
Download

Go to site of 17

Summary
  • KTI Networks KPOE-800-1P - page 1

    Modular 8-Port Mid-span Power over Ethernet Injector KPOE-800-1P KPOE-800-2P Installation Guide 1 DOC.090201 ...

  • KTI Networks KPOE-800-1P - page 2

    (C) 2008 KTI Networks Inc. All rights reserved. No part of this documentation m ay be reproduced in any form or by any mean s or used to make any di rective work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time ...

  • KTI Networks KPOE-800-1P - page 3

    The information contained in this docu ment is subject to change without prior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class A Part 15 the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful in terf ...

  • KTI Networks KPOE-800-1P - page 4

    Table of Contents 1. Introduction ............................................................................................................................... .5 1.1 Features ................................................................................................................. 5 1.2 Product Panels ..................................... ...

  • KTI Networks KPOE-800-1P - page 5

    1. Introduction The Power over Ethernet (PoE) injector is a mid-sp an power injector designed and tested for use with all IEEE802.3af compatible PoE Powered Devices (PDs ). The PoE injector sits between a switch port and the PoE powered device, providing inline pow er capability to an un-powered switch port. The injector provides modular power desi ...

  • KTI Networks KPOE-800-1P - page 6

     Modular PoE power upgradability  19" rack mounting support 1.2 Product Panels The following figure illustrates the faces of the injector: 1.3 Mid-span Injector Function The PoE mid-span power injector is designed and t ested for use with all IEEE802.3af com patible PoE PDs. The PoE injector sits between a switch port and the PoE powered ...

  • KTI Networks KPOE-800-1P - page 7

    1.4 Model Definition KPOE-800-1P 1 Power Model The injector unit with one pre-installed power module KPOE-800-2P 2 Power Model The injector unit with two pre-installed power modules KPOE-800P60W Power Module PoE 60W Power Module KPOE-800BSET1 BRACKET SET1 The bracket set for mounting one unit in a 19” rack KPOE-800BSET2 BRACKET SET2 The bracket s ...

  • KTI Networks KPOE-800-1P - page 8

    8 - Disconnection, - Overload, - Over-current - Short-circuit, - Under voltage Power Module Slots 2 LED Indicators Power module status x 2 , Port PoE status x 8 Power Input Voltage: 100 ~ 240VAC, Frequency: 50/60Hz Power Consumption 1 Power Model: 68W max. (60W for remote PoE PDs) 2 Power Model: 136W max. (120W for remote PoE PDs) Power Dissipation ...

  • KTI Networks KPOE-800-1P - page 9

    9 2. Installation 2.1 Unpacking Check that the following components have been included:  Information CD  The device unit  An AC power cord If any item is found missing or damaged, please contact your local reseller for replacement. The following are available optional accessories:  19” rack mounting bracket kits The brackets are used ...

  • KTI Networks KPOE-800-1P - page 10

    2.3 Mounting the Injector Desktop Mounting The injector can be mounted on a deskto p or shelf. Make sure there is proper heat dissipation f rom and adequate ventilation around the device. Do not place heavy objects on the device. Rack Mounting The following brackets are designed for u se to mount the devices in a 19” rack. Mounting one unit in a ...

  • KTI Networks KPOE-800-1P - page 11

    2. Install the long bracket to the other side of the device. 3. Mount the device in a 19” rack. Mounting two units in a rack Use the bracket set 2 and follow the steps shown below:  Short bracket x 4  Joint bracket x 1 1. Install two short brackets to both sides of each device. 2. Joint two units together as shown below: 11 ...

  • KTI Networks KPOE-800-1P - page 12

    3. Mount two device units as one in a 19” rack. 2.4 Installing Power Module If you purchased 2 Power Model, you may skip this section. 1 Power Model can deliver total up t o 60W for consuming by all eight ports. Calculat e the total power budget required for your PD connections before making any connections. Most of common PoE powered devices suc ...

  • KTI Networks KPOE-800-1P - page 13

    3. Install the power module into the slot until it is seated properly. 4. Screw the module in the injector securely. 2.5 Applying AC Power One AC power cord, which meets the specification of your country of origin was supplied with the device unit. The device supports wide range of AC power input specifications as follows: Specifications Power Rati ...

  • KTI Networks KPOE-800-1P - page 14

    3. Making LAN Connections 3.1 Making Switch Port Connections The mid-span injector is designed to support th e following PoE incapable switch port t ypes and the PoE function is transparent and independe nt to the following port configuration: IEEE 802.3 std. 10BASE-T 100BASE-TX 1000BASE-T Port Configuration Auto-negotiation: Enable or disable Tran ...

  • KTI Networks KPOE-800-1P - page 15

    3.2 Making Powered Device Connections The mid-span injector supports connection to I EEE 802.3af compliant PoE PD (Powered Device). The Ethernet port of the PD can be Ethernet, Fast Ethe rnet or Gigabit Ethernet. The injector’s PoE OUT port delivers power together with network signal to a connected powered device via Cat.5 cable or better. To mak ...

  • KTI Networks KPOE-800-1P - page 16

    Short-circuit A short-circuit situation is detected on the port. Under voltage An under-voltage situation is detected on the port. 3.3 LED Indication LED Function State Interpretation P1 Power 1 status ON Power 1 is ON. OFF Power 1 is OFF. P2 Power 2 status ON Power 2 is ON. OFF Power 2 is OFF. 1 ~ 8 Port 1 ~ Port 8 PoE status ON Port PoE power is ...

  • KTI Networks KPOE-800-1P - page 17

    4. Applications 4.1 Application with Low Power Requirements 1 Power model may be used if the total power budge t of the connected PDs is less than 60Watts. One empty slot can be upgraded with one more power if total power budget increased and is more than 60W in future. 4.2 Application with High Power Requirements 2 Power model can support the tota ...

Manufacturer KTI Networks Category Switch

Documents that we receive from a manufacturer of a KTI Networks KPOE-800-1P can be divided into several groups. They are, among others:
- KTI Networks technical drawings
- KPOE-800-1P manuals
- KTI Networks product data sheets
- information booklets
- or energy labels KTI Networks KPOE-800-1P
All of them are important, but the most important information from the point of view of use of the device are in the user manual KTI Networks KPOE-800-1P.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals KTI Networks KPOE-800-1P, service manual, brief instructions and user manuals KTI Networks KPOE-800-1P. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product KTI Networks KPOE-800-1P.

Similar manuals

A complete manual for the device KTI Networks KPOE-800-1P, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use KTI Networks KPOE-800-1P by users. Manuals are usually written by a technical writer, but in a language understandable to all users of KTI Networks KPOE-800-1P.

A complete KTI Networks manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual KTI Networks KPOE-800-1P - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the KTI Networks KPOE-800-1P, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the KTI Networks KPOE-800-1P, that we can find in the current document
3. Tips how to use the basic functions of the device KTI Networks KPOE-800-1P - which should help us in our first steps of using KTI Networks KPOE-800-1P
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with KTI Networks KPOE-800-1P
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of KTI Networks KPOE-800-1P in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning KTI Networks KPOE-800-1P?

Use the form below

If you did not solve your problem by using a manual KTI Networks KPOE-800-1P, ask a question using the form below. If a user had a similar problem with KTI Networks KPOE-800-1P it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)